Without clearing OPEN flag in failure path, runtime or system resume
may submit interrupt/rx URB and start tx queue mistakenly on a
interface in DOWN state.
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ignoring interfaces with additional descriptors is not a reliable
method for locating the correct interface on Gobi devices.  There
is at least one device where this method fails:
https://bbs.archlinux.org/viewtopic.php?id=143506

The result is that the AT command port (interface #2) is hidden
from qcserial, preventing traditional serial modem usage:

[   15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device
[   15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[   15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22
[   15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device
[   15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[   15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22
[   15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected
[   15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0
[   15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected
[   15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1

Use static interface numbers taken from the interface map in
qcserial for all Gobi devices instead:

	Gobi 1K USB layout:
	0: serial port (doesn't respond)
	1: serial port (doesn't respond)
	2: AT-capable modem port
	3: QMI/net

	Gobi 2K+ USB layout:
	0: QMI/net
	1: DM/DIAG (use libqcdm from ModemManager for communication)
	2: AT-capable modem port
	3: NMEA

This should be more reliable over all, and will also prevent the
noisy "probe failed" messages.  The whitelisting logic is expected
to be replaced by direct interface number matching in 3.6.
Reported-by: NHeinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de>
Cc: <stable@vger.kernel.org> # v3.4: 00001880 USB: qmi_wwan: Make forced int 4 whitelist generic
Cc: <stable@vger.kernel.org> # v3.4: f7142e6c USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z
Cc: <stable@vger.kernel.org> # v3.4
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the change "mac80211: remove spurious BSSID change flag",
BSS_CHANGED_BSSID will not be passed on association or IBSS
status changes. So it could be better to program bssid on ASSOC
or IBSS change notification. Not doing so, is affecting the
packet transmission.

Cc: stable@vger.kernel.org [3.4+]
Reported-by: NMichael Leun <lkml20120218@newton.leun.net>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When debugging is disabled, the event log functions aren't
functional in the way that the debugfs file expects. This
leads to the debugfs access crashing. Since the event log
functions aren't functional then, remove the debugfs file
when CONFIG_IWLWIFI_DEBUG is not set.

Cc: stable@kernel.org
Reported-by: NLekensteyn <lekensteyn@gmail.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"ath9k: Fix softlockup in AR9485" with commit id
64bc1239 fixed the reported
issue, yet its better to avoid the possible infinite loop
in ar9003_get_pll_sqsum_dvc by having a timeout as suggested
by ath9k maintainers.
http://www.spinics.net/lists/linux-wireless/msg92126.html.
Based on my testing PLL's locking measurement is done in
~200us (2 iterations).

Cc: stable@vger.kernel.org
Cc: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes two memory leaks in the SPI initialization code.

Patch based on old maemo patch by:
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Always report beacon loss to the stack, not only when in powersave
state. This is because there's possibility that the driver disables
PSM before it handles old BSS_LOSE_EVENT, so beacon loss has to be
reported.

Patch based on old maemo patch by:
Janne Ylalehto <janne.ylalehto@nokia.com>
Juuso Oikarinen <juuso.oikarinen@nokia.com>
Luciano Coelho <luciano.coelho@nokia.com>
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cast MSB part of current TSF to u64 to prevent loss of most
significant bits. MSB should also be shifted by 32.

Patch based on old maemo patch by:
Yuri Kululin <ext-yuri.kululin@nokia.com>
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a memory leak that was introduced in the 3.4 kernel.  The
leak occurred when FCoE was enabled and traffic was passed over the FCoE
rings reserved for FCoE.  The memory leak was due to us not populating the
compound page information on the order 1 pages needed for FCoE.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix Kconfig file to make sure that PTP and IGB/IXGBE are both either
in-kernel or modules, not mixed.  Having the build status mixed causes
compile errors.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i210/i211 device has only 16 RAR address filters like 82575, instead of
32 like i350.  This patch removes the entries for i210/i211 in the
get_invariants function which was setting them for 32. This ensures that
they will get the default value which is the correct one.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

add_virtual_intf() needs to return an ERR_PTR(), instead of NULL,
on errors, otherwise cfg80211 will crash.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"qual" used to be declared on the stack, but then in 998a5a7d ("airo:
reduce stack memory footprint") we made it dynamically allocated.
Unfortunately the memcpy() here was missed and it's still copying stack
memory instead of the data that we want.  In other words, "&qual" should
be "qual".
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When running heavy traffic we stop the tx queue if the pending
packet count reaches certain threshold. Later, the tx queue should
be woken up as soon as the packet count falls below the threshold.

Current code wakes TX queue up on STA interface only. Removing the
check for STA interface will allow both STA and AP interfaces to
resume transmit when tx_pending count becomes low.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

spin_unlock_bh(&txq->lock) already disables softirqs so we don't want
to do it here.  Fixes smatch warnings:

   drivers/net/wireless/ath/ath5k/base.c:1048 ath5k_drain_tx_buffs() error: double lock 'bottom_half:'
   drivers/net/wireless/ath/ath5k/base.c:1056 ath5k_drain_tx_buffs() error: double unlock 'bottom_half:'
Reported-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After setup_frame_info has been called, only info->control.rates is still
valid, other control fields have been overwritten by the ath_frame_info
data. Move the access to info->control.vif for checking short preamble
to setup_frame_info before it gets overwritten.

This regression was introduced in commit d47a61aa
"ath9k: Fix multi-VIF BSS handling"
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reported-by: NThomas Hühn <thomas@net.t-labs.tu-berlin.de>
Acked-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: stable@vger.kernel.org [3.4]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rate pointer variable for a rate series is used in a loop before it is
initialized. This went unnoticed because it was used earlier for the RTS/CTS
rate. This bug can lead to the wrong PHY type being passed to the
duration calculation function.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On a freescale imx6q platform, a hardware phy chip KSZ9021 is
recognized as a KS8001 chip by the current driver like this:
eth0: Freescale FEC PHY driver [Micrel KS8001 or KS8721]

KSZ9021 has phy_id 0x00221610, while KSZ8001 has phy_id
0x0022161a, the current phy_id_mask (0x00fffff0/0x00ffff10) can't
distinguish them. So change phy_id_mask to resolve this problem.

Although the micrel datasheet says that the 4 LSB of phyid2 register
contains the chip revision number and the current driver is designed
to follow this rule, in reality the chip implementation doesn't follow
it.

Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NHui Wang <jason77.wang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vendor-specific events shall be processed in driver and not sent
to bluetooth stack where they screw up HCI command countings.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

There are four link statuses of a bonding slave, the procfs
code shows a wrong status when using downdelay/updelay:

	(slave->link == BOND_LINK_UP) ?  "up" : "down"

It doesn't respect the rest two statuses. This patch fixes it.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As seen on smsc75xx, driver_info->description being longer than 32
characters messes up 'ethtool -i' output.
Signed-off-by: NPhil Sutter <phil.sutter@viprinet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increasing the hardware statistics structure to accomodate statistics for skyhawk.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify IOCTL error message to print subsystem also.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The maximum size of packet that can be handled by controller including ethernet
header is 65535. Reducing gso_max_size accordingly.
Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a potential hole when configuring the cycle counter used to
generate the nanosecond time clock. This clock is based off of the SYSTIME
registers along with the TIMINCA registers. The TIMINCA register determines
the increment to be added to the SYSTIME registers every DMA clock tick. This
register needs to be reconfigured whenever the link-speed changes. However,
the value calculated stays the same when link is down and when link is up.
Misconfiguration can occur if the link status changes due to a reset, which
causes the TIMINCA register to be reset. This reset puts the device in an
unstable state where the SYSTIME registers stop incrementing and the PTP
protocol does not function.

The solution is to double check the TIMINCA value and always reset the value
if the register is zero. This prevents a misconfiguration bug that halts the
PHC.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I2C is not responding it's usually due to a previous
unexpected reset during I2C operation. We release it by
powering down and up the SFP+ module.
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The adapter->npars[] array has QLCNIC_MAX_PCI_FUNC elements.  We
allocate it that way a few lines earlier in the function.  So this test
is off by one.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a off by one error in the minimal number of BD in
bnx2x_start_xmit() and bnx2x_tx_int() before stopping/resuming tx queue.

A full size GSO packet, with data included in skb->head really needs
(MAX_SKB_FRAGS + 4) BDs, because of bnx2x_tx_split()

This error triggers if BQL is disabled and heavy TCP transmit traffic
occurs.

bnx2x_tx_split() definitely can be called, remove a wrong comment.
Reported-by: NTomas Hruby <thruby@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(CAN_CTRLMODE_LISTENONLY & CAN_CTRLMODE_LOOPBACK) is (0x02 & 0x01) which
is zero so the condition is never true.  The intent here was to test
that both flags were set.

Cc: <stable@kernel.org> # 2.6.39+
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x driver incorrectly sets ip_summed to CHECKSUM_UNNECESSARY on
encapsulated segments. TCP stack happily accepts frames with bad
checksums, if they are inside a GRE or IPIP encapsulation.

Our understanding is that if no IP or L4 csum validation was done by the
hardware, we should leave ip_summed as is (CHECKSUM_NONE), since
hardware doesn't provide CHECKSUM_COMPLETE support in its cqe.

Then, if IP/L4 checksumming was done by the hardware, set
CHECKSUM_UNNECESSARY if no error was flagged.

Patch based on findings and analysis from Robert Evans
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up

	Call Trace:
	[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
	[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
	[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
	[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
	[<ffffffff810744fe>] process_one_work+0x11e/0x470
	[<ffffffff8107530f>] worker_thread+0x15f/0x360
	[<ffffffff810751b0>] ? manage_workers+0x230/0x230
	[<ffffffff81079af3>] kthread+0x93/0xa0
	[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
	[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
	[<ffffffff815fd3a0>] ? gs_change+0x13/0x13

ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.

fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142Reported-by: NRolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org [3.0+]
Tested-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver supports a maximum number of ports configurable at compile
time. Make sure the probe() method fails when registering a port that
exceeds the maximum instead of returning success without registering the
port.

This fixes a crash at system suspend time, when the driver tried to
suspend a non-registered port using the UART core.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When probing fails, the driver must not try to cleanup resources that
have not been initialized. Fix this.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

In the transmit path of the bonding driver, skb->cb is used to
stash the skb->queue_mapping so that the bonding device can set its
own queue mapping.  This value becomes corrupted since the skb->cb is
also used in __dev_xmit_skb.

When transmitting through bonding driver, bond_select_queue is
called from dev_queue_xmit.  In bond_select_queue the original
skb->queue_mapping is copied into skb->cb (via bond_queue_mapping)
and skb->queue_mapping is overwritten with the bond driver queue.

Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes
the packet length into skb->cb, thereby overwriting the stashed
queue mappping.  In bond_dev_queue_xmit (called from hard_start_xmit),
the queue mapping for the skb is set to the stashed value which is now
the skb length and hence is an invalid queue for the slave device.

If we want to save skb->queue_mapping into skb->cb[], best place is to
add a field in struct qdisc_skb_cb, to make sure it wont conflict with
other layers (eg : Qdiscc, Infiniband...)

This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8
bytes :

netem qdisc for example assumes it can store an u64 in it, without
misalignment penalty.

Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[].
The largest user is CHOKe and it fills it.

Based on a previous patch from Tom Herbert.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NTom Herbert <therbert@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we modify primary via sysfs and it is not a valid slave,
we should record it for future use, and this behavior is the same with
bond_check_params().
Signed-off-by: NWeiping Pan <wpan@redhat.com>
Acked-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test procedure:
1. Start AP with security setting (e.g. WPA2)
2. Stop AP
3. Start AP with open security

Here it's observed that privacy is enabled in beacons and
probe responses.

This patch fixes it by checking the privacy parameter from
cfg80211_ap_settings. If privacy is not set in cfg80211_ap_settings,
set open authentication and no encryption in FW.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A regression was introduced in the 3.3 rc series, commit
"drm/ttm: simplify memory accounting for ttm user v2",
causing the metadata of buffer objects created using the ttm_bo_create()
function to be accounted twice.
That causes massive leaks with the vmwgfx driver running for example
SpecViewperf Catia-03 test 2, eventually killing the app.

Furthermore, the same commit introduces a regression where
metadata accounting is leaked if a buffer object is
initialized with an illegal size. This is also fixed with this commit.

v2: Fixed an error path and removed an unused variable.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

clear the platform data pointer when mxs_pinctrl_probe_dt fails,
and also before the unregistering with pinctrl subsystem.
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

if there is no purecfg , the group pointer is allocated using kzalloc and if it
fails to allocate, we wont free the new_map,

if config is true, we call kmemdup and if it
fails to do so we wont free the allocated group if there is no purecfg.

fix this by doing the frees of new_map pointer and group pointers.
Acked-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>