This lets userspace determine what the state of the RTS line is, which
is what is needed to properly handle data flow for this device (it
raises RTS when there is data to be sent from it.)

Cc: Kees Stoop <kees.stoop@opticon.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch allows data to be sent to the scanner.

Cc: Kees Stoop <kees.stoop@opticon.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

NOP transceiver is used by all the usb transceiver which are mostly
autonomous and doesn't require any programming or which are built
into the usb ip itself.NOP transceiver only allocates the memory
for struct xceiv and calls otg_set_transceiver() so function call
to otg_get_transceiver() will return a valid transceiver.

NOP transceiver device should be registered by calling
usb_nop_xceiv_register() from platform files.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove some pointless messages from the FTDI serial driver;
I found these filling up syslog on one system.  Also remove
a pointless "break" after a "return" in the same area.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the usb subsystem.
Signed-off-by: NFrank Seidel <frank@f-seidel.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes use of the generic method if a serial driver provides
no implementation. This simplifies implementing suspend/resume support
in serial drivers.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This exports a symbol for usb_serial_generic_resume, so that modules can
use it.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This removes an unnecessary check for autoresume from the generic
resume method. The check has been obsoleted by the now delayed
increase of the usage counter which makes the error this check prevented
impossible. This change allows drivers which only use the bulk read URB
the use of the generic method even if they support autosuspend.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB: serial: introduce a flag into the usb serial layer to tell drivers that their URBs are killed due to suspension

This patch introduces a flag into the usb serial layer to tell drivers
that their URBs are killed due to suspension. That is necessary to let
drivers know whether they should report an error back.
Signed-off-by: NOliver Neukum <oneukum@suse.de>

Hi Greg,

this is for 2.6.30. Patches to use this in drivers are under development.

	Regards
		Oliver

With a postfix decrement count will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this does the standard support for suspend/resume for the opticon
driver.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch implements suspend and resume methods for the
option driver. With my hardware I can even suspend the system
and keep up a connection for a short time.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-Off-By: NMatthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Workaround of hw bug in IMX UDC.
This bug causes wrong handling of CFG_CHG interrupt.
Workaround is documented inline source code.
Signed-off-by: NDarius Augulis <augulis.darius@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix ep0 interrupt handling in IMX UDC Gadget.
Signed-off-by: NDarius Augulis <augulis.darius@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix code style errors in IMX UDC Gadget.
Signed-off-by: NDarius Augulis <augulis.darius@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix small bugs and add some omptimization in IMX UDC Gadget.
Signed-off-by: NDarius Augulis <augulis.darius@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixup of Werner Cornelius patch to the ch341 USB-serial driver, which adds:
- support all baudrates, not just a hard-coded set
- support for controlling DTR, RTS and CTS

Features still missing:
- character length other than 8 bits
- parity settings
- break control

I adapted his patch for the new usb_serial API introduced in 2.6.25-git8 by
Alan Cox on 22 July 2008. Non-compliance to the new API was a reason for
refusing a similar patch from Tollef Fog Heen.

Usage example by Tollef Fog Heen :
        TEMPer USB thermometer <http://err.no/src/TEMPer.c>
Signed-off-by: NWerner Cornelius <Werner.Cornelius@cornelius-consult.de>
Signed-off-by: NBoris Hajduk <boris@hajduk.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Removed duplicated #include in
  drivers/usb/gadget/ci13xxx_udc.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This set of patches introduces calls to the following set of functions:

usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)

In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:

USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC

An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)

@r5@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
-  \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)

@inc@
@@

#include <linux/usb.h>

@depends on !inc && (r1||r5)@
@@

+ #include <linux/usb.h>
  #include <linux/usb/...>
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

priv is checked not to be NULL near the beginning of the function and not
changed subsequently, making the test redundant.

A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@

if (x@p1 == NULL || ...) { ... when forall
   return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
x@p2 == NULL
|
x@p2 != NULL
)

// another path to the test that is not through p1?
@s exists@
local idexpression r.x;
position r.p1,r.p2;
@@

... when != x@p1
(
x@p2 == NULL
|
x@p2 != NULL
)

@fix depends on !s@
position r.p1,r.p2;
expression x,E;
statement S1,S2;
@@

(
- if ((x@p2 != NULL) || ...)
  S1
|
- if ((x@p2 == NULL) && ...) S1
|
- BUG_ON(x@p2 == NULL);
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This set of patches introduces calls to the following set of functions:

usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)

In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:

USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC

An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)

@r5@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
-  \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)

@inc@
@@

#include <linux/usb.h>

@depends on !inc && (r1||r5)@
@@

+ #include <linux/usb.h>
  #include <linux/usb/...>
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The functions:

usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_is_isoc_in(epd)
usb_endpoint_is_isoc_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)

are moved from include/linux/usb.h to include/linux/usb/ch9.h.
include/linux/usb/ch9.h makes more sense for these functions because they
only depend on constants that are defined in this file.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add the vbus_draw() callback to inform the transceiver, if
it exists, how much current may be drawn. The decision is
taken on gadget driver side using the configuration chosen
by the host and its bMaxPower field.  Some systems can use
the host's VBUS supply to augment or recharge a battery.
(There's also a default of 100 mA for unconfigured devices,
or 8 mA if they're OTG devices.)
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a transceiver driver is used, no automatic udc enable
is done. The transceiver (OTG or not) should :
 - take care of VBus sensing
 - call usb_gadget_vbus_connect()
 - call usb_gadget_vbus_disconnect()

The pullup should remain within this driver's management,
either by gpio_pullup of udc_command() fields.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On vbus_session() call, optionally activate D+ pullup
resistor and enable the udc, or deactivate D+ pullup
resistor and disable the udc.

It is intentional to not handle any VBus sense related irq.
An external transceiver driver (like gpio_vbus) should
catch VBus sense signal, and call usb_gadget_vbus_connect()
or usb_gadget_vbus_disconnect().
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Prepare pxa27x_udc to handle usb D+ pullup properly : it
should connect the pullup resistor and disconnect it only
if no external transceiver is handling it.

[ dbrownell@users.sourceforge.net: kerneldoc and gpio fixes ]
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Call usb_gadget_vbus_connect() and ...disconnect() from a
workqueue rather than from an irq handler, allowing msleep()
calls in vbus_session.  Update kerneldoc to match.

[ dbrownell@users.sourceforge.net: more kerneldoc updates ]
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usblp in 2.6.18 polled for status regardless if we actually needed it.
At some point I dropped it, to save the batteries if nothing else.
As it turned out, printers exist (e.g. Canon BJC-3000) that need prodding
this way or else they stop. This patch restores the old behaviour.
If you want to save battery, don't leave jobs in the print queue.

I tested this on my printers by printing and examining usbmon traces
to make sure status is being requested and printers continue to print.
Tuomas Jäntti verified the fix on BJC-3000.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1203) increases the max_sector limit for USB tape
drives.  By default usb-storage sets max_sectors to 240 (i.e., 120 KB)
for all devices.  But tape drives need a higher limit, since tapes can
and do have very large block sizes.  Without the ability to transfer
an entire large block in a single command, such tapes can't be used.

This fixes Bugzilla #12207.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NPhil Mitchell <philipm@sybase.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Restore some code that was wrongly dropped from the RNDIS
driver, and caused interop problems observed with OpenMoko.

The issue is with hardware which needs help conforming to part
of the USB 2.0 spec (section 8.5.3.2); some can automagically
send a ZLP in response to an unexpected IN, but not all chips
will do that.  We don't need to check the packet length ourselves
the way earlier code did, since the UDC must already check it.
But we do need to tell the UDC when it must force a short packet
termination of the data stage.

(Based on a patch from Aric D. Blumer <aric at sdgsystems.com>)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Apparently the Configuration and Interface strings aren't used as
often as the Vendor, Product, and Serial strings.  In at least one
device (a Saitek Cyborg Gold 3D joystick), attempts to read the
Configuration string cause the device to stop responding to Control
requests.

This patch (as1226) adds a quirks flag, telling the kernel not to
read a device's Configuration or Interface strings, together with a
new quirk for the offending joystick.
Reported-by: NMelchior FRANZ <melchior.franz@gmail.com>
Tested-by: NMelchior FRANZ <melchior.franz@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>  [2.6.28 and 2.6.29, nothing earlier]
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

With a sufficiently new compiler and binutils, code which wasn't
previously generating .eh_frame sections has begun to.  Certain
architectures (powerpc, in this case) may generate unexpected relocation
formats in response to this, preventing modules from loading.

While the new relocation types should probably be handled, revert to the
previous behaviour with regards to generation of .eh_frame sections.

(This was reported against Fedora, which appears to be the only distro
doing any building against gcc-4.4 at present: RH bz#486545.)
Signed-off-by: NKyle McMartin <kyle@redhat.com>
Acked-by: NRoland McGrath <roland@redhat.com>
Cc: Alexandre Oliva <aoliva@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Revert the change to the orphan dates of Windows 95, DOS, compression.
Add a new orphan date for OS/2.
Signed-off-by: NJody McIntyre <scjody@sun.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
  ucc_geth: Fix oops when using fixed-link support
  dm9000: locking bugfix
  net: update dnet.c for bus_id removal
  dnet: DNET should depend on HAS_IOMEM
  dca: add missing copyright/license headers
  nl80211: Check that function pointer != NULL before using it
  sungem: missing net_device_ops
  be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle
  be2net: replenish when posting to rx-queue is starved in out of mem conditions
  bas_gigaset: correctly allocate USB interrupt transfer buffer
  smsc911x: reset last known duplex and carrier on open
  sh_eth: Fix mistake of the address of SH7763
  sh_eth: Change handling of IRQ
  netns: oops in ip[6]_frag_reasm incrementing stats
  net: kfree(napi->skb) => kfree_skb
  net: fix sctp breakage
  ipv6: fix display of local and remote sit endpoints
  net: Document /proc/sys/net/core/netdev_budget
  tulip: fix crash on iface up with shirq debug
  virtio_net: Make virtio_net support carrier detection
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix crash with /proc/iomem
  sparc64: Reschedule KGDB capture to a software interrupt.
  sbus: Auto-load openprom module when device opened.

This patch fixes bug #12208:

  Bug-Entry       : http://bugzilla.kernel.org/show_bug.cgi?id=12208
  Subject         : uml is very slow on 2.6.28 host

This turned out to be not a scheduler regression, but an already
existing problem in ptrace being triggered by subtle scheduler
changes.

The problem is this:

 - task A is ptracing task B
 - task B stops on a trace event
 - task A is woken up and preempts task B
 - task A calls ptrace on task B, which does ptrace_check_attach()
 - this calls wait_task_inactive(), which sees that task B is still on the runq
 - task A goes to sleep for a jiffy
 - ...

Since UML does lots of the above sequences, those jiffies quickly add
up to make it slow as hell.

This patch solves this by not rescheduling in read_unlock() after
ptrace_stop() has woken up the tracer.

Thanks to Oleg Nesterov and Ingo Molnar for the feedback.
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/powerpc:
  powerpc/mm: Fix Respect _PAGE_COHERENT on classic ppc32 SW TLB load machines

Grant picked up the wrong version of "Respect _PAGE_COHERENT on classic
ppc32 SW" (commit a4bd6a93)

It was missing the code to actually deal with the fixup of
_PAGE_COHERENT based on the CPU feature.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

commit b1c4a9dd ("ucc_geth: Change
uec phy id to the same format as gianfar's") introduced a regression
in the ucc_geth driver that causes this oops when fixed-link is used:

Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0151270
Oops: Kernel access of bad area, sig: 11 [#1]
TMCUTU
NIP: c0151270 LR: c0151270 CTR: c0017760
REGS: cf81fa60 TRAP: 0300   Not tainted  (2.6.29-rc8)
MSR: 00009032 <EE,ME,IR,DR>  CR: 24024042  XER: 20000000
DAR: 00000000, DSISR: 20000000
TASK = cf81cba0[1] 'swapper' THREAD: cf81e000
GPR00: c0151270 cf81fb10 cf81cba0 00000000 c0272e20 c025f354 00001e80
cf86b08c
GPR08: d1068200 cffffb74 06000000 d106c200 42024042 10085148 0fffd000
0ffc81a0
GPR16: 00000001 00000001 00000000 007ffeb0 00000000 0000c000 cf83f36c
cf83f000
GPR24: 00000030 cf83f360 cf81fb20 00000000 d106c200 20000000 00001e80
cf83f360
NIP [c0151270] ucc_geth_open+0x330/0x1efc
LR [c0151270] ucc_geth_open+0x330/0x1efc
Call Trace:
[cf81fb10] [c0151270] ucc_geth_open+0x330/0x1efc (unreliable)
[cf81fba0] [c0187638] dev_open+0xbc/0x12c
[cf81fbc0] [c0187e38] dev_change_flags+0x8c/0x1b0

This patch fixes the issue by removing offending (and somewhat
duplicate) code from init_phy() routine, and changes _probe()
function to use uec_mdio_bus_name().

Also, since we fully construct phy_bus_id in the _probe() routine,
we no longer need ->phy_address and ->mdio_bus fields in
ucc_geth_info structure.

I wish the patch would be a bit shorter, but it seems like the only
way to fix the issue in a sane way. Luckily, the patch has been
tested with real PHYs and fixed-link, so no further regressions
expected.
Reported-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>