提交 · fa8419d08e58c82add921b4e4eb01eb589b8586b · openeuler / Kernel

14 2月, 2009 17 次提交

ath5k: Don't call reset on config_interface · fa8419d0

由 Nick Kossifidis 提交于 2月 09, 2009

 * We call reset too often and this can result various PHY problems.
  On config_interface we don't need to reset the whole device.

  TODO: Create a function hw_fast_reset that only resets the PCU
  (tx/rx stuff) and not the whole device so that we can use this for
  stuck beacons etc.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

fa8419d0

ath5k: Disable BMISS interrupts · 1e3e6e8f

由 Nick Kossifidis 提交于 2月 09, 2009

 * Don't enable BMISS interrupts as we don't handle them yet
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

1e3e6e8f

ath5k: Update reset code · e8f055f0

由 Nick Kossifidis 提交于 2月 09, 2009

 * Update reset and sync with HALs

 * Clean up eeprom settings and tweaking of initvals and
   put them on separate functions

 * Set/Restore 32KHz ref clk operation

 * Add some more documentation

 TODO: Spur mitigation, tpc, half/quarter rate, compression etc

 v2: Address comments from Bob and Felix and fix RSSI threshold bug
 introduced on the first version of the patch
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

e8f055f0

ath5k: Update initvals · a406c139

由 Nick Kossifidis 提交于 2月 09, 2009

 * Update initvals to match legacy and Sam's HAL
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

a406c139

ath5k: Update RF Buffer handling · 8892e4ec

由 Nick Kossifidis 提交于 2月 09, 2009

 * Use the new way to modify rf buffer and put some rf buffer
   documentation on rfbufer.h

 * Merge all rf regs functions to one

 * Sync with legacy HAL and Sam's HAL

 * Set gain_F settings so that gain_F optimization engine works
   on RF5111/RF5112 (note that both HALs only use step 0 for RF5111
   and they don't use gain_F optimization for this chip, code is
   there but is never used)
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

8892e4ec

ath5k: Update gain_F calibration code and add documentation · 6f3b414a

由 Nick Kossifidis 提交于 2月 09, 2009

 * Update and cleanup rf gain optimization code

 * Add comments and refferences to docs and use sane function names

 * Use only step index on ath5k_gain, no need to have a pointer to
   the current step since we can determine te step from it's index,
   this also allows us to put all other structs on rfgain.h and cleanup
   ath5k.h a little

 * No need for ah_rfgain variable, we use ah_gain.g_state for everything

 * Tested on RF2112B chip but gain_F calibration is not yet done
   (we will finish this on the next patch where we'll rewrite rf-buffer
   handling)

 * Use initial rf gain settings for 2316 and 2317 SoCs introduced on a previous patch

 It seems big but it's mostly cleanup, very few functional changes have been made on phy.c
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

6f3b414a

ath5k: PHY code cleanup · 33a31826

由 Nick Kossifidis 提交于 2月 09, 2009

 * Clean up initial rf buffer settings (new file rfbufer.h) and introduce a
   new way to access specific rf registers (will use it later)

 * Clean up initial rf gain settings by moving them on a new file (rfgain.h)
   so we can later work on gain optimization functions

 * Update initial rf buffer settings and initial rf gain settings from HALs.
   This breaks things for now because our current dumps come from pre-configured
   rf buffer (regdumps already had the needed values set from binary HAL).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

33a31826

mac80211: Remove TSF atomic requirement from the documentation · 7b08b3b4

由 Alina Friedrichsen 提交于 2月 05, 2009

The atomic requirement for the TSF callbacks
is outdated. get_tsf() is only called by
ieee80211_rx_bss_info() which is indirectly
called by the work queue ieee80211_sta_work().
In the same context are called several other
non-atomic functions, too.
And the atomic requirement causes problems
for drivers of USB wifi cards.
Signed-off-by: NAlina Friedrichsen <x-alina@gmx.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

7b08b3b4

mac80211: Fix the wrong WARN_ON message appearing on enabling power save. · 97d97b80

由 Vivek Natarajan 提交于 2月 05, 2009

This issue happens only when we are associated with a 11n AP and power save
is enabled. In the function 'ieee80211_master_start_xmit', ps_disable_work
is queued where wake_queues is called. But before this work is executed,
we check if the queues are stopped in _ieee80211_tx and return TX_AGAIN to
ieee8011_tx which leads to the warning message.
This patch fixes this erroneous case.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

97d97b80

orinoco: hermes doesn't need to be a separate module · dec59d6f