WoL handling for the RTL8168 family is a little bit tricky because of
different types of broken BIOS and/or chip quirks.

Two known issues:
1. Network properly resumes from suspend only if WoL is enabled in the chip.
2. Some notebooks wake up immediately if system is suspended and network
   device is wakeup-enabled.

Few patches tried to deal with this:
7edf6d31 ("r8169: disable WOL per default")
18041b52 ("r8169: restore previous behavior to accept BIOS WoL
settings")

Currently we have the situation that the chip WoL settings as set by
the BIOS are respected (to prevent issue 1), but the device doesn't get
wakeup-enabled (to prevent issue 2).

This leads to another issue:
If systemd is told to set WoL it first checks whether the requested
settings are active already (and does nothing if yes). Due to the chip
WoL flags being set properly systemd assumes that WoL is configured
properly in our case. Result is that device doesn't get wakeup-enabled
and WoL doesn't work (until it's set e.g. by ethtool).

This patch now:
- leaves the chip WoL settings as is (to prevent issue 1)
- keeps the behavior to not wakeup-enable the device initially
  (to prevent issue 2)
- In addition we report WoL as being disabled in get_wol, matching
  that device isn't wakeup-enabled. If systemd is told to enable WoL,
  it will therefore detect that it has to do something and will
  call set_wol.

Of course the user still has the option to override this with
e.g. ethtool.

v2:
- Don't just exclude __rtl8169_get_wol() from compiling, remove it.
v3:
- adjust commit message
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable EEE per default on RTL8168f.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add EEE support for RTL8168f to the recently added EEE handling
framework in the driver. This patch leaves the chip defaults, means
EEE typically is disabled initially and it's up to the user to enable
it via ethtool.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable EEE per default on chip versions from RTL8168g.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the general framework to deal with EEE in this driver
plus EEE support for chip versions from RTL8168g. We don't touch the
default chip settings, therefore EEE will usually be disabled and it's
up to the user to enable it.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Few chip versions use the same sequence to adjust 10M and ALDPS, so
let's factor it out. This patch also fixes a (most likely) typo in
rtl8168g_1_hw_phy_config. There bit 8 in reg 0x14 on page 0x0bcc
was set and not cleared. According to the vendor driver this bit
needs to be cleared in all cases.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Chip versions from RTL8168g onward use the same sequence to disable
ALDPS (Advanced Link-Down Power Saving). So let's factor this out.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far member rtl_fw has three states:
- IS_ERR(rtl_fw): firmware not loaded
- !rtl_fw: no firmware available
- other: firmware loaded

This can be made simpler and clearer by adding the firmware name as
member fw_name to struct rtl8169_private. Then:

- !fw_name: no firmware available
- !rtl_fw: firmware not loaded
- rtl_fw: firmware loaded

This change also allows to easily merge rtl_request_uncached_firmware
into rtl_request_firmware.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The old non-PCIe chip versions support PCI DAC, however this feature
seems to be fragile, see comment in the PCI error handler. Therefore
it's disabled per default. I think meanwhile it's time remove support
for this legacy feature. This helps to reduce complexity of the driver.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

8 years ago, as part of 6f0333b8 ("r8169: use 50% less ram for RX
ring"), the alignment requirement for rx buffers was silently changed
from 8 bytes to 16 bytes. I found nothing explaining this, also the
chip specs I have only mention an 8 byte requirement.
AFAICS kmalloc_node() guarantees allocated memory to be at least
"long long" aligned, what is 8 bytes on a 32 bit machine.
So we can take this memory as-is and avoid some overhead by changing
the alignment requirement back to 8 bytes.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtl_init_one() is complex enough, so we better factor out getting the
ether_clk.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Accessing the phy_device indirectly via the netdevice causes few issues:
- Accessing the phy_device when it's not attached may cause a NPE.
- If we have to access the phy_device when it's not attached we have
  to use mdiobus_get_phy() to get a reference to the phy_device.

Therefore store a phy_device reference in struct rtl8169_private directly.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Triggering an asynchronous reset is problematic for the following
reasons, therefore reset the chip synchronously.

- The reset routine resets registers and parameters behind our back
  what may collide with code executed after triggering the reset.

- __rtl8169_resume() is called as part of pm_runtime_get_sync() and
  callers expect that the chip is fully resumed afterwards.

In context of this driver triggering an asynchonous reset should be
considered an emergency procedure.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add helpers for locking / unlocking the config registers.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All calls to this function have the enable parameter set to false.
So we can replace the function with a disable-only version.

v2:
- fixed copy & paste error
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's sufficient to initialize the workqueue once, therefore remove the
additional initialization whenever rtl_open() is called.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtl8169_hw_reset() is called as part of the reset routine which is
scheduled in the line after. So we can remove the call to
rtl8169_hw_reset() here.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This helper is used only once, so remove it.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This soft dependency works around an issue where sometimes the genphy
driver is used instead of the dedicated PHY driver. The root cause of
the issue isn't clear yet. People reported the unloading/re-loading
module r8169 helps, and also configuring this soft dependency in
the modprobe config files. Important just seems to be that the
realtek module is loaded before r8169.

Once this has been applied preliminary fix 38af4b90 ("net: phy:
add workaround for issue where PHY driver doesn't bind to the device")
will be removed.

Fixes: f1e911d5 ("r8169: add basic phylib support")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid log spam caused by trying to read counters from the chip whilst
it is in a PCI power-save state.

Reference: https://bugzilla.kernel.org/show_bug.cgi?id=107421

Fixes: 1ef7286e ("r8169: Dereference MMIO address immediately before use")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two new Realtek Ethernet devices which are re-branded r8168h.
Add the IDs to to support them.
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rtl8169_runtime_resume() we configure WoL but don't set the device
to wakeup-enabled. This prevents PME generation once the cable is
re-plugged. Fix this by moving the call to device_set_wakeup_enable()
to __rtl8169_set_wol().

Fixes: 433f9d0d ("r8169: improve saved_wolopts handling")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve detection of spurious interrupts by checking against the
interrupt mask as currently set in the chip.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_DEBUG_SHIRQ is enabled __free_irq() intentionally fires
a spurious interrupt. This interrupt causes a crash because
tp->dev->phydev is NULL at that time.

Fixes: 38caff5a ("r8169: handle all interrupt events in the hard irq handler")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

writex() has implicit barriers, that's what makes it different from
writex_relaxed(). Therefore these calls to mmiowb() can be removed.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that synchronize_rcu() waits for preempt-disable regions of code
as well as RCU read-side critical sections, synchronize_sched() can be
replaced by synchronize_rcu().  This commit therefore makes this change.
Signed-off-by: NPaul E. McKenney <paulmck@linux.ibm.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <netdev@vger.kernel.org>

Make use of xmit_more and add the functionality introduced with
3e59020a ("net: bql: add __netdev_tx_sent_queue()").
I used the mlx4 driver as template.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace macro TX_FRAGS_READY_FOR with function rtl_tx_slots_avail
to make code cleaner and type-safe.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use napi_consume_skb() where possible to profit from
bulk free infrastructure.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the GMII chip versions we set the version number which was set
already. This can be simplified.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even the chip versions within a family have so many differences that
using a default chip version doesn't really make sense. Instead
of leaving a best case flaky network connectivity, bail out and
report the unknown chip version.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove ancient GCC bug workaround in a second place and factor out
rtl_8169_get_txd_opts1.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only the upper 12 bits are used for chip identification, this helps
to reduce the size of array mac_info.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtl8168_oob_notify is used in rtl8168dp_driver_start and
rtl8168dp_driver_stop only, so we can rename it to r8168dp_oob_notify.
The same applies to condition rtl_ocp_read_cond which can be renamed
to rtl_dp_ocp_read_cond. This allows to simplify the code.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel can't be built any longer with this ancient GCC version.
Eventually it becomes clear what this statement actually does.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The compiler takes care of alignment and padding, I see no need to
bother him with manual hints.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ones who want to know can easily identify whether chip is PCI or
PCIe based on the chip name. I doubt there's any benefit in this
message, so remove it.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The syslog message printed on driver load allows to easily identify
the mac version number (based on chip name and XID). So we don't
need this extra debug message which is wrong anyway because e.g.
RTL_GIGA_MAC_VER_01 has value 0.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using macro PCI_VDEVICE helps to simplify the PCI ID table.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently the "slow event" handler was removed, therefore the member
name isn't appropriate any longer. In addition store the full mask,
including the RTL_EVENT_NAPI interrupt source bits.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>