Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 26 2月, 2011 6 次提交
  3. 25 2月, 2011 17 次提交
  5. 19 2月, 2011 13 次提交
  7. 14 2月, 2011 4 次提交
    • J
      [SCSI] libsas: convert to libata new error handler · c299190b
      由 James Bottomley 提交于 
      The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling.  The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.

Finally, activate the port recovery of the libata error handler for
each port known to the host.  This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
      c299190b
    • J
      [SCSI] libata: separate error handler into usable components · 64878c0e
      由 James Bottomley 提交于 
      Right at the moment, the libata error handler is incredibly
monolithic.  This makes it impossible to use from composite drivers
like libsas and ipr which have to handle error themselves in the first
instance.

The essence of the change is to split the monolithic error handler
into two components: one which handles a queue of ata commands for
processing and the other which handles the back end of readying a
port.  This allows the upper error handler fine grained control in
calling libsas functions (and making sure they only get called for ATA
commands whose lower errors have been fixed up).

Cc: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
      64878c0e
    • J
      [SCSI] libata: fix eh locking · 4451ef63
      由 James Bottomley 提交于 
      The SCSI host eh_cmd_q should be protected by the host lock (not the
port lock).  This probably doesn't matter that much at the moment,
since we try to serialise the add and eh pieces, but it might matter
in future for more convenient error handling.  Plus this switches
libata to the standard eh pattern where you lock, remove from the cmd
queue to a local list and unlock and then operate on the local list.

Cc: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
      4451ef63
    • J
      [SCSI] libata: fix locking for sas paths · b8784f77
      由 James Bottomley 提交于 
      For historical reasons, libsas uses the scsi host lock as the ata port
lock, and libata always uses the ata host.  For the old eh, this was
largely irrelevant since the two locks were never mixed inside the
code.  However, the new eh has a case where it nests acquisition of
the host lock inside the port lock (this does look rather deadlock
prone).  Obviously this would be an instant deadlock if the port lock
were the host lock, so switch the libsas paths to use the ata host
lock as well.

Cc: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
      b8784f77