Transport code currently calls itself through the transport ops,
which is quite pointless. Clean up all of this. While at it,
remove the unnecessary dir argument and the redundant IDI code.

In slave transports, call both the common slave debugfs and the
transport's own. SDIO has no files, so remove it all there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add ability to set the continuous recording mode of the FW, while
the FW debug data is configured to be stored on the NIC.
This could be useful for storing large segments of FW usniffer
debug data on the host, while having small store space on the NIC.
The host receives the usniffer data through the regular RX path, and
the data can get extracted using trace-cmd.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The fw debug functionality is big enough to warrant
a separate file. Move existing related functions to the new file.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The d0i3_mode element is never set to IWL_D0I3_OFF, so it's not
necessary to check it in iwl_mvm_is_d0i3_supported().
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There is a potential race condition when entering suspend with d0i3 in
PCIe.  If there is a frame queued just before we suspend, it won't
complete and we will never clear the queue stuck timer.  To solve
this, call TX_PATH_FLUSH to flush all queues (except the command
queue) as part of the d0i3 entry process.  Add a new function that
returns all the flushable queues.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the prph registers dump is in the transport layer,
and each bus needs an additional dump implementation.

Move the prph dump outside transport, and allow a common
implementation for all of the buses.
This is possible because prph base addresses are similar for
all buses.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Expose _no_grab prph i/o functions that allow performing i/o
outside the transport, without requiring grab and release NIC access
for each operation. In addition, rename the functions so they reflect
their non-grabbing behavior.

This can be very useful for consecutive prph i/o operation that occur
outside trans, such as fw dumps.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This was an old workaround for solving latency issues with
certain Miracast adapters like ActionTec. However this isn't
needed anymore and furthermore it hurts throughput in other
use cases.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the netdetect debugfs entry was removed, the nd_config element
was accidentally left in the iwl_mvm structure.  Remove it.

Fixes: dbb04b0d ("iwlwifi: mvm: remove netdetect debugfs entry")
Reported-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As part of the bt_notif file add fields that are currently
not represented
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add mplut and sync2sco and corunning to debugfs.
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The d0i3 flag in the device configuration structure is redundant,
because the same information can be determined by checking the
firmware capability flag.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This will allow to catch different TDLS events and get the
firmware data when they occur.
Add empty TX_LATENCY trigger on the way to avoid mismatch
with trees in which this trigger is implemented.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware debug trigger ID is always a compile-time constant,
so we can use a build-time assertion to validate that it is in
fact a valid constant.

To make that really guaranteed to work, convert this and the
inline function iwl_fw_dbg_trigger_simple_stop() to macros.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This function updates the pairwise keys as well.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The PCIe transport will also need a d0i3_entry_timeout_ms parameter,
so move the existing one from the slave transports to iwlwifi, so it
can be reused.  While at it, rename the parameter to something
shorter, namely d0i3_entry_delay.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This message isn't very useful and presents a security risk
due to the use of %p - remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of using an external NVM file, the driver sends to the
FW the different nvm sections. In the response of the cmd, the
FW states the status of the writing of the chunk.

Currently the value is not checked by the driver.

Check FW's response for writing the nvm chunk in the NVM_ACCESS_CMD.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the firmware sends LMAC scan notifications while a UMAC scan is
running, just WARN and ignore it, otherwise the scanning state gets
messed up.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When there's a bt-wifi contention that requires arbitration,
we use a priority-based mechanism to decide which comm wins.
Over time, use cases become more and more complex, with multiple
concurrent active links with different traffic types and different QoS
requirements, on both WiFi and BT sides.
This, in turn, requires us to elaborate our prioritization mechanism.
However, our legacy products included hw that does not supports this,
so selectively enable this on specific hw - as signaled by the firmware.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This code was needed during initial PAN bringup, but now is
just cruft - remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Configure the FW to use fragmented scan when the traffic load is high
or low latency traffic is on. This is useful for scans that are
managed by the FW (e.g. scheduled scan).
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make the various conversion functions typesafe, so we don't
accidentally try to call them with the wrong pointers and
cast them to something that will crash.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The split of iwlwifi into DVM and MVM was a long time ago now,
so we can remove the "default IWLWIFI" that we had to keep all
existing .config files with working defaults during the split.
This is no longer necessary, practically nobody should now be
upgrading a .config that's older than the split.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

802.11ac allows A-MSDU that can be up to 12KB long. Since
an entire A-MSDU needs to fit into one single Receive
Buffer (RB), add support for big RBs.
Since this adds lots of pressure to the memory manager and
significantly increase the true_size of the RX buffers,
don't enable this by default.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is a workaround to an OTP bug. In Series 8000 1x1, the OTP
0xA052 defines 2x2 antenna configuration. This workaround overrides
the decision based on HW id and on MIMO disabled bit which is
correct in the OTP and set to disabled. This fixes the previous
workaround "force 1x1 antenna in Series 8000".
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

mac80211_hwsim was not placed alphabetically correctly in menuconfig, fix that.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Change menuconfig to config to keep the Kconfig entries unified. Part of
reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Rename WL_TI to WLAN_VENDOR_TI to match with other vendor configs and make sure
that it's enabled by default in new configs. Convert menuconfigs to regular
configs to unify the wireless drivers menuconfig. Part of reorganising wireless
drivers directory and Kconfig.

Also remove WLCORE dependency to WL_TI. It should not be needed as WLCORE is
already under if  WLAN_VENDOR_TI.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add new a Kconfig file and a vendor config for realtek. Also update MAINTAINERS
which we missed to do when earlier moving rtlwifi.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>