In the NAPI poll function, check for netif_running() is unnecassary.
In addition to associated runtime overhead, it also results in
continuous softirq loop when the interface is brought down under heavy
traffic(tested with Traffic Generator).Once the interface is disabled,
the poll function always returns zero(with the check for netif_running)
and napi_complete() would never get called resulting in softirq loop.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the existing random_ether_addr() to generate random MAC
instead of doing it by-hand.
Signed-off-by: NStanislav O. Bezzubtsev <stas@lvk.cs.msu.su>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The version string already contains the printk level
specifying it again results in the following message
being printed:
<6>r6040: RDC R6040 NAPI ...
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In r8169 driver MTU is used to calculate receive buffer size.
Receive buffer size is used to configure hardware incoming packet filter.

For jumbo frames:
Receive buffer size = Max frame size = MTU + 14 (ethernet header) + 4
(vlan header) + 4 (ethernet checksum) = MTU + 22

Bug:
driver for all MTU up to 1536 use receive buffer size 1536

As you can see from formula, this mean all IP packets > 1536 - 22
(for vlan tagged, 1536 - 18 for not tagged) are dropped by hardware
filter.

Example:

host_good>  ifconfig eth0 mtu 1536
host_r8169> ifconfig eth0 mtu 1536
host_good>  ping host_r8169
Ok
host_good>  ping -s 1500 host_r8169
Fail
host_good>  ifconfig eth0 mtu 7000
host_r8169> ifconfig eth0 mtu 7000
host_good>  ping -s 1500 host_r8169
Ok

Bonus: got rid of magic number 8
Signed-off-by: NRaimonds Cicans <ray@apollo.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the missing "get_xstats_size" callback for the
netlink interface, which is required if "fill_xstats" is used,
as pointed out by Patrick McHardy.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In 2.6.32-rc the new EMS USB CAN driver was contributed and added the Kconfig
entry right behind an entry of the same *vendor*. This teared the SJA1000
based driver selection into pieces.

This fix cleans up the 2.6.32-rc Kconfig files for the CAN drivers and moves
the SJA1000 and USB Kconfig portions into the belonging directories.

As there are many new CAN drivers in the queue getting this cleanup into
2.6.32-rc would massively reduce the problems for the upcoming drivers.

Thanks,
Oliver
Signed-off-by: NOliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due commit 4b77b0a2, it is not more
possible to pci_restore_state() more than once without calling
pci_save_state() in the middle.

Actually running a ethtool test on s2io makes the card inactive,
and it needs to unload/reload the module to fix.

This patch just save the state just after it restore in order to
keep the old behaviour
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turn on RTS/CTS for HT to prevent uCode TX fifo underrun

This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: NJiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.

The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.

When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.

By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.

For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Configuration of wake-on-lan for unicast, multicast, broadcast, physical
activity was not working. Kernel panic issue was there when user tries to
disable WOL. Fixed them.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to a missing header include, sparse generates the following warnings:

  CHECK   drivers/net/wireless/rtl818x/rtl8187_rfkill.c
warning: symbol 'rtl8187_rfkill_init' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_poll' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_exit' was not declared. Should it be static?
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setup the GPIOs for the BenQ Joybook netbook.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add GPIO configuration for the Compaq CQ60 laptop
Reported-by: NDavid Dreggors <ddreggors@jumptv.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should not zero out the multicast hash when configuring
the operating mode, since a zero value means all multicast
frames will get dropped.  Also, ath5k_mode_setup() gets
called after any reset, so the hash already set up in
configure_filter() is lost.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ops->set_tim() must be atomic, so b43 trying to acquire a mutex leads
to a kernel crash. This patch trades an easy to trigger crash in AP
mode for an unlikely race condition. According to Michael, the real
fix would be to allow set_tim() to sleep, since b43 is not the only
driver that needs to sleep in all callbacks.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

or it will taint the kernel and fail to load becuase
of_address_to_resource() is GPL only.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On older kernels, e.g. 2.6.27, a WARN_ON dump in rtmsg_ifinfo()
is thrown when the CAN device is registered due to insufficient
skb space, as reported by various users. This patch adds the
rtnl_link_ops "get_size" to fix the problem. I think this patch
is required for more recent kernels as well, even if no WARN_ON
dumps are triggered. Maybe we also need "get_xstats_size" for
the CAN xstats.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device requires a fundamental reset when recovering from EEH.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This line was accidentally left out of the previous commit #
da039451 ("qlge: Fix firmware mailbox
command timeout.").
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When ioatdma was loaded we we were unable to transmit traffic.  We weren't
using the correct registers in ixgbe_update_tx_dca for 82599 systems.
Likewise in ixgbe_configure_tx() we weren't disabling the arbiter before
modifying MTQC.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When DCB is enabled, the ixgbe_check_tx_hang() should check the corresponding
TC's TXOFF in TFCS based on the TC that the tx ring belongs to. Adds a
function to map from the tx_ring hw reg_idx to the correspodning TC and read
TFCS accordingly.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 32k gso_max_size when DCB is enabled is for 82598 only, not for 82599.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No-one seems to know where the PowerBook 500 series store their ethernet
MAC addresses. So, rather than crash, use a MAC address from the SONIC
CAM. Failing that, generate a random one.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stanse found that one error path in cas_open omits to unlock pm_mutex.
Fix that.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPC-USB is using a ARM7 core with little endian byte order. The "id" field
in can_msg needs byte order conversion from/to CPU byte order.
Signed-off-by: NSebastian Haas <haas@ems-wuensche.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sending config commands to be2 hardware before netdev_register is
completed, is sometimes causing the async link notification to arrive
even before the driver is ready to handle it. The commands for vlan
config and flow control settings can infact wait till be_open.
This patch takes care of that.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If be2 goes into suspend after a user changes the flow control settings,
we are not programming them back after resume. This patch takes care of it.
We now get the flow control settings before going to suspend mode and
then apply them during resume.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This prevents the rt2x00 driver from queueing ieee80211 work after the  
USB card has been removed, preventing a kernel panic.
Signed-off-by: NSean Cross <sean@chumby.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit e6c5fc53.

Based on this regression report:

Date: Thu, 05 Nov 2009 15:59:16 +0100
From: Holger Schurig <holgerschurig@gmail.com>
To: linux-wireless@vger.kernel.org
Subject: BUG: oops when "rmmod ipw2200"

This happened on wireless-testing v2.6.32-rc6-41575-g5e68bfb. I
modprobed ipw2200, put it into monitor mode, used tshark a while to
monitor, then I stopped tshark, "ifconfig eth2 down" and finally
"rmmod ipw2200", and voila:

[  917.189620] ------------[ cut here ]------------
[  917.189717] kernel BUG at net/wireless/core.c:543!
[  917.189805] invalid opcode: 0000 [#1] PREEMPT SMP
[  917.190002] last sysfs file: /sys/devices/pci0000:00/0000:00:1e.0/0000:02:0d.0/firmware/0000:02:0d.0/loading
[  917.190136] Modules linked in: lib80211_crypt_wep ipw2200(-) libipw lib80211 ath5k mac80211 ath cfg80211 psmouse uhci_hcd
[  917.190680]
[  917.190759] Pid: 1763, comm: rmmod Not tainted (2.6.32-rc6-wl #26) Amilo M1425
[  917.190886] EIP: 0060:[<f8accf34>] EFLAGS: 00010202 CPU: 0
[  917.190992] EIP is at wiphy_unregister+0xd3/0x175 [cfg80211]
[  917.191083] EAX: f601d4c4 EBX: 00000000 ECX: 00000000 EDX: f79e8600
[  917.191176] ESI: f601d400 EDI: f95b4350 EBP: f6009eb4 ESP: f6009e8c
[  917.191269]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  917.191360] Process rmmod (pid: 1763, ti=f6008000 task=f79e8130 task.ti=f6008000)
[  917.191486] Stack:
[  917.191562]  f601d5a0 f601d484 f6460e98 f6009ea0 c01407ee f6009eb8 00000246 f64604c0
[  917.191916] <0> f6460e5c f95b4350 f6009ec0 f94fd030 f6460e98 f6009edc f95a9d4f f787bc00
[  917.192100] <0> f787bc58 f787bc00 f95b4350 f95b4350 f6009ee8 c0207fca f787bc58 f6009ef8
[  917.192100] Call Trace:
[  917.192100]  [<c01407ee>] ? trace_hardirqs_on+0xb/0xd
[  917.192100]  [<f94fd030>] ? unregister_ieee80211+0xe/0x27 [libipw]
[  917.192100]  [<f95a9d4f>] ? ipw_pci_remove+0x59/0x227 [ipw2200]
[  917.192100]  [<c0207fca>] ? pci_device_remove+0x19/0x39
[  917.192100]  [<c02b93a4>] ? __device_release_driver+0x59/0x9d
[  917.192100]  [<c02b944f>] ? driver_detach+0x67/0x85
[  917.192100]  [<c02b88d6>] ? bus_remove_driver+0x69/0x85
[  917.192100]  [<c02b9878>] ? driver_unregister+0x4d/0x54
[  917.192100]  [<c02081c3>] ? pci_unregister_driver+0x28/0x71
[  917.192100]  [<f95a9cf4>] ? ipw_exit+0x1c/0x1e [ipw2200]
[  917.192100]  [<c0148e2b>] ? sys_delete_module+0x192/0x1ef
[  917.192100]  [<c0162cdb>] ? remove_vma+0x52/0x58
[  917.192100]  [<c01028bb>] ? sysenter_exit+0xf/0x18
[  917.192100]  [<c0102888>] ? sysenter_do_call+0x12/0x36
[  917.192100] Code: 74 07 e8 81 bc 8c c7 eb c8 8d 55 e0 89 f8 e8 d6 6d 66 c7 8b 45 dc 31 d2 e8 81 cc 8c c7 8d 86 c4 00 00 00 39 86 c4 00 00 00 74 04 <0f> 0b eb fe 8b 45 dc 8d 5e 0c e8 5a cc 8c c7 8b 86 94 03 00 00
[  917.192100] EIP: [<f8accf34>] wiphy_unregister+0xd3/0x175 [cfg80211] SS:ESP 0068:f6009e8c
[  917.203718] ---[ end trace bcaaf449945a5100 ]---
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit

	3d1285be (move virtnet_remove to .devexit.text)

introduced the first reference to __devexit in struct virtio_driver
virtio_net which upset modpost ("Section mismatch in reference from the
variable virtio_net to the function .devexit.text:virtnet_remove()").

Fix this by renaming virtio_net to virtio_net_driver.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: NMichael S. Tsirkin <mst@redhat.com>
Blame-taken-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Rick Farina (sidhayn@gmail.com), removing the RTL8187
USB stick, or unloading the driver rtl8187 using rmmod will cause a
kernel oops.  There are at least two forms of the failure, (1) BUG:
Scheduling while atomic, and (2) a fatal kernel page fault. This
problem is reported in Bugzilla #14539.

This problem does not occur for kernel 2.6.31, but does for 2.6.32-rc2,
thus it is technically a regression; however, bisection did not locate
any faulty patch. The fix was found by comparing the faulty code in
rtl8187 with p54usb.  My interpretation is that the handling of work
queues in mac80211 changed enough to the LEDs to be unregistered
before tasks on the work queues are cancelled. Previously, these
actions could be done in either order.

(Herton Ronaldo Krzesinski <herton@mandriva.com.br> reports that the
code is the same in 2.6.31, so this may be a candidate for 2.6.31.x.
-- JWL)
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reported-by: NRick Farina <sidhayn@gmail.com>
Tested-by: NRick Farina <sidhayn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

emac_irq is declared as:

static irqreturn_t emac_irq(int irq, void *dev_id)
{
       struct net_device *ndev = (struct net_device *)dev_id;
       struct emac_priv *priv = netdev_priv(ndev);
    ... 

	Clearly emac_irq() needs "struct net_device *" as "void *dev_id", so correct this.
Signed-off-by: NTonyliu <Bo.Liu@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTorgny Johansson <torgny.johansson@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On a 64-bit kernel, skb->tail is an offset, not a pointer. The libertas
usb driver passes it to usb_fill_bulk_urb() anyway, causing interesting
crashes. Fix that by using skb->data instead.

This highlights a problem with usb_fill_bulk_urb(). It doesn't notice
when dma_map_single() fails and return the error to its caller as it
should. In fact it _can't_ currently return the error, since it returns
void.

So this problem was showing up only at unmap time, after we'd already
suffered memory corruption by doing DMA to a bogus address.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch e43419f9:

	ath9k: downgrade assert in rc.c for invalid rate

downgraded an ASSERT to a WARN_ON() but also misplaced a
semicolon at the end of the second check. What this did
was force the rate control code to always return the rate
even if we should have warned about it. Since this should
not have happened anymore anyway this fix isn't critical
as the proper rate would have been returned anyway.

Cc: stable@kernel.org
Reported-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

b43 allocates a bouncebuffer, if the supplied TX skb is in an invalid
memory range for DMA.
However, this is broken in that it fails to copy over some metadata to the
new skb.

This patch fixes three problems:
* Failure to adjust the ieee80211_tx_info pointer to the new buffer.
  This results in a kmemcheck warning.
* Failure to copy the skb cb, which contains ieee80211_tx_info, to the new skb.
  This results in breakage of various TX-status postprocessing (Rate control).
* Failure to transfer the queue mapping.
  This results in the wrong queue being stopped on saturation and can result in queue overflow.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Tested-by: NChristian Casteyde <casteyde.christian@free.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

stolen from windows inf file(07/17/2009, 1.03.05.0000)
Ovislink 0x1b75, 0x7318
MSI 0x0db0, 0x4600
WideTell 0x7167, 0x3840
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For non-monitor interfaces, the syntax for alloc_ieee80211/free_80211
is wrong. Because alloc_ieee80211 only creates (wiphy_new) a wiphy, but
free_80211() does wiphy_unregister() also. This is only correct when
the later wiphy_register() is called successfully, which apparently
is not the case for your fw doesn't exist one.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>