Wa_16012360555 SW will have to program the "LP to HS Wakeup Guardband"
field to account for the repeaters on the HS Request/Ready PPI signaling
between the Display engine and the DPHY.

v2: Fix build issue.
v3: Align to new naming (Jani)
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826054811.10572-2-vandita.kulkarni@intel.com

At this point is sure that HSW and BDW will never have PSR enabled by
default, so here dropping it from device info and cleaning up code.

v2:
- enable psr support for display 9
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-1-jose.souza@intel.com

UHBR modes has higher link rate and added new values for programming
mpll of SNPS phy. No change in sequence, only the pll parameters
are different for UHBR modes.
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827103843.527-1-jani.nikula@intel.com

Add the registers for specifying the lower and higher 24 bits of the DP
2.0 pixel clock frequency in Hz.

Bspec: 53326
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9047f10318a30bc03ce8516ee3f5512437a95663.1629735412.git.jani.nikula@intel.com

This register controls the DP 2.0 datapath.

Bspec: 69967
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0d3529df4501c5dd8ad1da0b6dbaabcfa97510b4.1629735412.git.jani.nikula@intel.com

Polish the FBC stride override stuff:
- just call it override_cfb_stride since it'll be used on
  more gens later
- Use REG_BIT() & co. for the registers and give everything
  CHICKEN_ prefix since glk+ will have a different register
  for this
- Use intel_de_rmw() for the RMW
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210702204603.596-5-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Till DISPLAY12 the PIPE_MISC bits 5-7 are used to set the
Dithering BPC, with valid values of 6, 8, 10 BPC.
For ADLP+ these bits are used to set the PORT OUTPUT BPC, with valid
values of: 6, 8, 10, 12 BPC, and need to be programmed whether
dithering is enabled or not.

This patch:
-corrects the bits 5-7 for PIPE MISC register for 12 BPC.
-renames the bits and mask to have generic names for these bits for
dithering bpc and port output bpc.

v3: Added a note for MIPI DSI which uses the PIPE_MISC for readout
for pipe_bpp. (Uma Shankar)

v2: Added 'display' to the subject and fixes tag. (Uma Shankar)

Fixes: 756f85cf ("drm/i915/bdw: Broadwell has PIPEMISC")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210811051857.109723-1-ankit.k.nautiyal@intel.com

Although DG2_G10 platforms will always have all SQIDI's present and
don't need steering for registers in a SQIDI MMIO range, this isn't true
for DG2_G11 platforms; only SQIDI's 2 and 3 can be used on those.

We handle SQIDI ranges a bit differently from other types of explicit
steering.  The SQIDI ranges belong to either the MCFG unit or the SF
unit, both of which have their own dedicated steering registers and do
not use the typical 0xFDC steering control that all other types of
ranges use.  Thus we only need to worry about picking a valid initial
value for the MCFG and SF steering registers (0xFD0 and 0xFD8
respectively) at driver init; they won't change after we set them up so
we don't need to worry about re-steering them explicitly at runtime.

Given that any SQIDI value should work fine for DG2-G10 and XeHP SDV,
while only values of 2 and 3 are valid for DG2-G11, we'll just
initialize the MCFG and SF steering registers to a constant value of "2"
for all XeHP-based platforms for simplicity --- that will work in all
cases.

Bspec: 66534
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210729170008.2836648-6-matthew.d.roper@intel.com

Xe_HP is more modular than its predecessors and as a consequence it has
more types of replicated registers.  As with l3bank regions on previous
platforms, we may need to explicitly re-steer accesses to these new
types of ranges at runtime if we can't find a single default steering
value that satisfies the fusing of all types.

v2:
 - Add a local 'i915' variable to reduce gt->i915 usage.  (Caz)
 - Drop unused 'intel_gt_read_register' prototype.  (Caz)

v3:
 - Drop unnecessary comment text.  (Lucas)
 - Drop unused register bit definition.  (Lucas)

Bspec: 66534
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Caz Yokoyama <caz.yokoyama@intel.com>
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210729170008.2836648-2-matthew.d.roper@intel.com

Xe_HP no longer has "slices" in the same way that old platforms did.
There are new concepts (gslices, cslices, mslices) that apply in various
contexts, but for the purposes of fusing slices no longer exist and we
just have one large pool of dual-subslices (DSS) to work with.
Furthermore, the meaning of the DSS fuse is inverted compared to past
platforms --- it now specifies which DSS are enabled rather than which
ones are disabled.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NRadhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: NStuart Summers <stuart.summers@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NPrasad Nallani <prasad.nallani@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210729170008.2836648-9-matthew.d.roper@intel.com

Update the get/set min/max freq hooks to work for
SLPC case as well. Consolidate helpers for requested/min/max
frequency get/set to intel_rps where the proper action can
be taken depending on whether SLPC is enabled.

v2: Add wrappers for getting rp0/1/n frequencies, update
softlimits in set min/max SLPC functions. Also check for
boundary conditions before setting them.

v3: Address review comments (Michal W)

v4: Add helper for host part of intel_rps_set_freq helpers (Michal W)

v5: checkpatch()
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Acked-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NVinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NSujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-13-vinay.belgaumkar@intel.com

Cache rp0, rp1 and rpn platform limits into SLPC structure
for range checking while setting min/max frequencies.

Also add "soft" limits which keep track of frequency changes
made from userland. These are initially set to platform min
and max.

v2: Address review comments (Michal W)
v3: Formatting (Michal W)
v4: Add separate function to parse rp values (Michal W)
v5: Perform range checking for set min/max (Michal W)
v6: checkpatch() and rename static functions (Michal W)
v7: check ret code while setting SLPC limits (Michal W)
Signed-off-by: NVinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-12-vinay.belgaumkar@intel.com

The register offset for SFC_DONE was missing a '0' at the end, causing
us to read from a non-existent register address.  We only use this
register in error state dumps so the mistake hasn't caused any real
problems, but fixing it will hopefully make the error state dumps a bit
more useful for debugging.

Fixes: e50dbdbf ("drm/i915/tgl: Add SFC instdone to error state")
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728233411.2365788-1-matthew.d.roper@intel.comReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>

Remove registers that are not used anymore due to CNL removal and rename
those that are.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728215946.1573015-25-lucas.demarchi@intel.com

With the removal of CNL, let's consider ICL as the first platform using
those constants.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728215946.1573015-21-lucas.demarchi@intel.com

Remove support for CNL as it's highly untested, probably broken, and
there is no real platform that requires this code. This is part of CNL
removal from i915.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728215946.1573015-18-lucas.demarchi@intel.com

Remove special handling of PORT_F in i915_irq.c and only do it for
DISPLAY_VER == 11.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728215946.1573015-17-lucas.demarchi@intel.com

With the removal of CNL, let's consider GLK as the first platform using
those constants since GLK has DISPLAY_VER == 10.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728215946.1573015-16-lucas.demarchi@intel.com

The only real platform with DISPLAY_VER == 10 is GLK. We don't need to
handle CNL explicitly in intel_display_power.c.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728215946.1573015-14-lucas.demarchi@intel.com

The only real platform with DISPLAY_VER == 10 is GLK. We don't need to
handle CNL explicitly in intel_ddi.c.

A lot of special code for CNL can be removed. There were some
__cnl.*() functions that were created to share the implementation
between ICL and CNL. Those are now embedded in the only caller, in ICL.

Remove code and rename functions/macros accordingly to use ICL prefix
for those that are still needed.

Verified with:

	make EXTRA_CFLAGS=-Wunused drivers/gpu/drm/i915/display/intel_dpll_mgr.o
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210729233934.2059489-1-lucas.demarchi@intel.com

The only real platform with DISPLAY_VER == 10 is GLK, so we don't need
any checks and supporting code for CNL. Remove code and rename
functions/macros accordingly.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728215946.1573015-3-lucas.demarchi@intel.com

The PSR enable/disable sequences now require that we program an extra
register in the PHY to adjust the lane disable power setting.

Bspec: 49274
Bspec: 53885
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-29-matthew.d.roper@intel.com

Initialization of the PHY is handled by the hardware/firmware, but the
driver should wait up to 25ms for the PHY to report that its calibration
has completed.

Bspec: 49189
Bspec: 50107
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-28-matthew.d.roper@intel.com

Vswing programming for SNPS PHYs is just a single step -- look up the
value that corresponds to the voltage level from a table and program it
into the SNPS_PHY_TX_EQ register.

Bspec: 53920
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-26-matthew.d.roper@intel.com

At the moment we don't have a proper algorithm that can be used to
calculate PHY settings for arbitrary HDMI link rates.  The PHY tables
here should support the regular modes of real-world HDMI monitors.

Bspec: 54032
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-25-matthew.d.roper@intel.com

DG2's SNPS PHYs incorporate a dedicated port PLL called MPLLB which
takes the place of the shared DPLLs we've used on past platforms.  Let's
add the MPLLB programming sequences; they'll be plugged into the rest of
the code in future patches.

Bspec: 54032
Bspec: 53881
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NNidhi Gupta <nidhi1.gupta@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-24-matthew.d.roper@intel.com

The driver doesn't depend atm on the common mode timing generator
functionality (it would be used for some power saving feature and panel
timing synchronization), however DMC will corrupt the CMTG registers
across DC5 entry/exit sequences unless the CMTG clock gating is
disabled. This in turn can lead to at least the DPLL0/1 configuration
getting stuck at their last state, which means we can't reprogram them
to a new config.

Add the corresponding Bspec workaround to prevent the above.

v2: Fix checkpatch errors. (CI, Jose)

Cc: Uma Shankar <uma.shankar@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727134400.101290-1-imre.deak@intel.com

ADL_P requires that we disable underrun recovery when downscaling (or
using the scaler for YUV420 pipe output), using DSC, or using PSR2.
Otherwise we should be able to enable the underrun recovery.

On DG2 we need to keep underrun recovery disabled at all times, but the
chicken bit in PIPE_CHICKEN has an inverted meaning (it's an enable bit
instead of disable).

v2:
 - Reverse the condition (clear the disable bit when supported, set
   disable bit when not supported).

Bspec: 50351
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727145056.2049720-1-matthew.d.roper@intel.com

The driver must provide GuC with a list of mmio registers
that should be saved/restored during a GuC-based engine reset.
Unfortunately, the list must be dynamically allocated as its size is
variable. That means the driver must generate the list twice - once to
work out the size and a second time to actually save it.

v2:
 (Alan / CI)
  - GEN7_GT_MODE -> GEN6_GT_MODE to fix WA selftest failure
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Signed-off-by: NFernando Pacheco <fernando.pacheco@intel.com>
Signed-off-by: NMatthew Brost <matthew.brost@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMatthew Brost <matthew.brost@intel.com>
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-16-matthew.brost@intel.com

PSF GV points are an additional factor that can limit the
bandwidth available to display, separate from the traditional
QGV points.  Whereas traditional QGV points represent possible
memory clock frequencies, PSF GV points reflect possible
frequencies of the memory fabric.

Switching between PSF GV points has the advantage of incurring
almost no memory access block time and thus does not need to be
accounted for in watermark calculations.

This patch adds support for those on top of regular QGV points.
Those are supposed to be used simultaneously, i.e we are always
at some QGV and some PSF GV point, based on the current video
mode requirements.
Bspec: 64631, 53998

v2: Seems that initial assumption made during ml conversation
    was wrong, PCode rejects any masks containing points beyond
    the ones returned, so even though BSpec says we have around
    8 points theoretically, we can mask/unmask only those which
    are returned, trying to manipulate those beyond causes a
    failure from PCode. So switched back to generating mask
    from 1 - num_qgv_points, where num_qgv_points is the actual
    amount of points, advertised by PCode.

v3: - Extended restricted qgv point mask to 0xf, as we have now
      3:2 bits for PSF GV points(Matt Roper)
    - Replaced val2 with NULL from PCode request, since its not being
      used(Matt Roper)
    - Replaced %d to 0x%x for better readability(thanks for spotting)
Signed-off-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210531064845.4389-2-stanislav.lisovskiy@intel.com

According to BSpec there is now also a code 0x02,
which corresponds to QGV point being rejected,
this code so lets extend mask to check this.
Signed-off-by: NStanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210531064845.4389-1-stanislav.lisovskiy@intel.com

This is only used by GRAPHICS_VER == 6 and GRAPHICS_VER == 7. All other
recent platforms do not depend on this field, so it doesn't make much
sense to keep it generic like that. Instead, just do a mapping from
engine class to HW ID in the single place that is needed.

v2: use macros with the direct register address instead of calculating
from the legacy HW_ID (Matt Roper)
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723002551.3906535-1-lucas.demarchi@intel.com

Xe_HP can have a lot of extra media engines. This patch adds the reset
support for them.
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-5-matthew.d.roper@intel.com

Xe_HP can have a lot of extra media engines. This patch adds the
interrupt handler support for them.

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-4-matthew.d.roper@intel.com

Xe_HP can have a lot of extra media engines. This patch adds the basic
definitions for them.

v2:
 - Re-order intel_gt_info and intel_device_info slightly to avoid
   unnecessary padding now that we've increased the size of
   intel_engine_mask_t.  (Tvrtko)
v3:
 - Drop the .hw_id assignments.  (Lucas)
v4:
 - Fix graphics_ver typo for VCS4 (should be 12, not 11).  (Lucas)

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723191024.1553405-1-matthew.d.roper@intel.com

A new step has been added to the DP modeset sequences for all platforms
with display version 12 and beyond:  if enabling DP MST with FEC, we
need to set a chicken bit before enabling the transcoder.  The chicken
bit should be disabled again before disabling the transcoder (which we
can do unconditionally since it shouldn't be set anyway in non-MST
cases).

Bspec: 49190, 54128, 55424
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723170618.1477415-1-matthew.d.roper@intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

We kept adding new engines and for that increasing hw_id unnecessarily:
it's not used since GRAPHICS_VER == 8. Prepend "gen6" to the field and
try to pack it in the structs to give a hint this field is actually not
used in recent platforms.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720232014.3302645-4-lucas.demarchi@intel.com

Implement GuC context operations which includes GuC specific operations
alloc, pin, unpin, and destroy.

v2:
 (Daniel Vetter)
  - Use msleep_interruptible rather than cond_resched in busy loop
 (Michal)
  - Remove C++ style comment
v3:
 (Matthew Brost)
  - Drop GUC_ID_START
 (John Harrison)
  - Fix a bunch of typos
  - Use drm_err rather than drm_dbg for G2H errors
 (Daniele)
  - Fix ;; typo
  - Clean up sched state functions
  - Add lockdep for guc_id functions
  - Don't call __release_guc_id when guc_id is invalid
  - Use MISSING_CASE
  - Add comment in guc_context_pin
  - Use shorter path to rpm
 (Daniele / CI)
  - Don't call release_guc_id on an invalid guc_id in destroy
v4:
 (Daniel Vetter)
  - Add FIXME comment
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Signed-off-by: NMatthew Brost <matthew.brost@intel.com>
Reviewed-by: NJohn Harrison <John.C.Harrison@Intel.com>
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721215101.139794-7-matthew.brost@intel.com

Xe_HP changes the format of the context ID from past platforms.
Signed-off-by: NStuart Summers <stuart.summers@intel.com>
Signed-off-by: NUmesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721223043.834562-9-matthew.d.roper@intel.com

The current interrupt handler is getting increasingly complicated and
Xe_HP changes will bring even more complexity.  Let's split off a new
interrupt handler starting with DG1 (i.e., when the master tile
interrupt register was added to the design) and use that as the basis
for the new Xe_HP changes.

Now that we track the hardware IP's release number as well as the
version number, we can also properly define DG1 has version "12.10" and
replace the has_master_unit_irq feature flag with an IP version test.

Bspec: 50875
Cc: Daniele Spurio Ceraolo <daniele.ceraolospurio@intel.com>
Cc: Stuart Summers <stuart.summers@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NTomasz Lis <tomasz.lis@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721223043.834562-5-matthew.d.roper@intel.com