Support basic device tree boot on the Nomadik. Implement the
support in the cpu file with the intent of deleting the board
files later. At this stage IRQ controllers, system timer,
l2x0 cache, UARTs and thus console boot is fully functional.
Patch out the code adding devices by initcalls for now so
as not to disturb the boot.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

With the addition of commit a0ae0240 (ARM: kernel: add device tree init
map function), the cpu reg values must match the cpu mpidr register or we'll
get warnings. For some reason, the CLUSTERID on highbank is 9, so the reg
value needs to be 0x90n to quiet the warnings.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

While device_type is considered deprecated, it is still needed for tools
like lshw to identify cpu nodes.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The second FlexCAN port uses different clock than the first one, configure
correct clock to prevent hanging of the system during bringing up of the port.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

During merge of the mvebu patches a clock gate for pinctrl was
lost. This patch just readds the clock gate.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The Armada XP MV78230 DT include file is missing a ; at the
end of the cpu node.
Reported-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

We originally thought that the MV78230 variant of the Armada XP had
four Ethernet interfaces, like the other variants MV78260 and
MV78460. In fact, this is not true, and the MV78230 has only three
Ethernet interfaces.

So, the definitions of the Ethernet interfaces is now done as follows:

 * armada-370-xp.dtsi: definitions of the first two interfaces, that
   are common to Armada 370 and Armada XP

 * armada-xp.dtsi: definition of the third interface, common to all
   Armada XP variants.

 * armada-xp-mv78260.dtsi and armada-xp-mv78460.dtsi: definition of
   the fourth interface.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Contrary to our understanding at the time armada-xp-mv78230.dtsi was
written, the MV78230 variant of the Armada XP SoC has two cores and
not one. This patch updates the .dtsi file to take into account this
reality.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

With the change to a DT based pinctrl/gpio driver, using gpio API
calls in board-*.c files no longer works, a dereferenced NULL pointer
exception occurs instead. By converting the GPIO code into a
fixed-regulator which gets probed later once pinctrl/gpio is
available, we avoid the exception.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NStefan Peter <s.peter@mplch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Clock Management of kirkwood has moved to DT clock providers.
However, TWSI1 has not yet been done.
This switches TWSI1 of 88f6282 to DT clock providers.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Without the clock being held by a driver, it gets turned off at a bad
time causing the SoC to lockup. This is often during reboot.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NStefan Peter <s.peter@mpl.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The UART controller used in the Armada 370 and Armada XP SoCs is the
Synopsys DesignWare 8250 (aka Synopsys DesignWare ABP UART). The
improper use of the ns16550 can lead to a kernel oops during boot if
a character is sent to the UART before the initialization of the
driver. The DW APB has an extra interrupt that gets raised when
writing to the LCR when busy. This explains why we need to use
dw-apb-uart driver to handle this.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

In the compatible field we should point the manufacturer of the board, which
in this case is Buglabs.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to
probe when booting with DT.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Reduce the HDMI resource size from 0x100000 to 0x70000 so it
doesn't overlap the Displayport resource space.
HDMI: (0x14530000 - 0x145A0000)
DP: (0x145B0000 - 0x145B1000)
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NPrathyush K <prathyush.k@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Current nmk_pinctrl driver is not PRCMU dependent anymore, so it needs
its own DT address resources to work properly, as done for
platform_device in:

f4828336 ARM: ux500: add PRCM register base for pinctrl
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

On the imx23-olinuxino board GPIO2_1 is connected to the LED and GPIO0_17
is the USB PHY reset.

So make the IOMUX assignment properly.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Commit db5b0ae0 ("Merge tag 'dt' of git://git.kernel.org/.../arm-soc")
causes a duplicated build target.  This patch fixes it and sorts out the
build target alphabetically so that we can recognize something wrong
easily.

Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the rename portion of "ARM: sunxi: Change device tree naming
scheme for sunxi" that were missed when the patch was applied.
Signed-off-by: NOlof Johansson <olof@lixom.net>

There is several different SoCs sharing the sun5i codename: A10s, A12
and A13. Since there is enough differences to not consider those the
same SoCs, change a bit the naming scheme to reflect this.

Moreover, some boards like the olinuxino come in A10s and A13 variants,
which also share the same SoC codename.

So change the naming scheme to reflect both the codename and the market
name of the SoCs used in the dtsi and in the board files
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

FEC controller is connected to AIPI2 bus.

Also fix the AIPI1 address range.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Change the value of status to disabled to keep the consistent
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Commit 0d9250c4 (ARM: dts: omap4-panda: Add pinmux configuration for
HDMI) added a new device-tree source file for Rev A4 of the OMAP4430
Panda board but it did not add this version to the makefile. Hence,
add this file to the makefile.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The system memory node for the OMAP2420 H4 was incorrectly defined as
start address followed by end address, instead of start address and
size. No noticable side-effects were observed but fix this for
correctness.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The current rules have the .dtb files build in a different directory
from the .dts files. The only reason for this is that it was what
PowerPC has done historically. This patch changes ARM to use the generic
dtb rule which builds .dtb files in the same directory as the source .dts.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: NOlof Johansson <olof@lixom.net>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
[swarren: added rm command for old stale .dtb files]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

Add missing PL330 MDMA1 controller node to the device tree (DT).

[ Currently there is no problem with using 'non-secure' mdma1 address
  instead of 'secure' one on revision 0 of Exynos4210 SOC (as used by
  Universal C210 board) as this SOC revision is unsupported by DT. ]
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NYehuda Yitschak <yehuday@marvell.com>
Tested-and-reviewed-by: NYehuda Yitschak <yehuday@marvell.com>
Tested-and-reviewed-by: NLior Amsalem <alior@marvell.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This adds hrefprev60, hrefv60plus and ccu9540 to device trees compiled
during build.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>

GPIO numbers for the newly created gpio-regulator will differ from
board to board. Therefore it's not sensible to leave this information
in the top level DTSI file. Let's move them out to the DTS files
where they can correctly vary.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Not all supported boards will require a MMCI gpio-regulator,
therefore it's a good idea to only enable the node when and if
it is required. Let's disable it by default.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Patch f055f1f6 [ARM: sunxi: Add sun4i and cubieboard support] missed
this sun4i.dtsi include file. This patch finally brings it upstream
enabling support for sun4i boards.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>

This adds support for SPEAr320-HMI board.
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>

shirq layer has been adapted to DT, add corresponding nodes in all
SPEAr3xx variants.
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>

This patch adds multiple device nodes for SPEAr machines and boards.
Signed-off-by: NBhavna Yadav <bhavna.yadav@st.com>
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Signed-off-by: NRajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NVijay Kumar Mishra <vijay.kumar@st.com>
Signed-off-by: NVipin Kumar <vipin.kumar@st.com>
Signed-off-by: NVipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>

amba-pl011 driver supports two pin state "default" and "sleep" and it
expect from dt to provide this pinctrl states and phandler otherwise it
gives a warning message.

To remove this warning message pass default state with null phandler to uart
pins in device node (In our case all the pins are configured in default states
so we pass null phandler to pins).
Signed-off-by: NVipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>

This patch modifies the DT bindings for the GMAC IP existings for the
SPEAr family. The DT bindings now additionally pass the phy mode as a
configuration parameter for the ethernet device.
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>

This patch fixes existing DT support for all SPEAr SoC's. This includes:
- Removing few nodes from board files
- Updating DT data of few nodes
- Updating ranges of few busses
- Moving devices to correct parent bus
Signed-off-by: NBhavna Yadav <bhavna.yadav@st.com>
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Signed-off-by: NRajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NVijay Kumar Mishra <vijay.kumar@st.com>
Signed-off-by: NVipin Kumar <vipin.kumar@st.com>
Signed-off-by: NVipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>

This patch enhances partition information of MTD devices like fsmc-nand and
spear-smi.
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NVipin Kumar <vipin.kumar@st.com>
Signed-off-by: NVipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>