The Bluetooth technology introduces new features on a regular basis
and for some of them it is important that the hardware on both sides
support them. For features like Simple Pairing it is important that
the host stacks on both sides have switched this feature on. To make
valid decisions, a config stage during ACL link establishment has been
introduced that retrieves remote features and if needed also the remote
extended features (known as remote host features) before signalling
this link as connected.

This change introduces full reference counting of incoming and outgoing
ACL links and the Bluetooth core will disconnect both if no owner of it
is present. To better handle interoperability during the pairing phase
the disconnect timeout for incoming connections has been increased to
10 seconds. This is five times more than for outgoing connections.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Simple Pairing process can only be used if both sides have the
support enabled in the host stack. The current Bluetooth specification
has three ways to detect this support.

If an Extended Inquiry Result has been sent during inquiry then it
is safe to assume that Simple Pairing is enabled. It is not allowed
to enable Extended Inquiry without Simple Pairing. During the remote
name request phase a notification with the remote host supported
features will be sent to indicate Simple Pairing support. Also the
second page of the remote extended features can indicate support for
Simple Pairing.

For all three cases the value of remote Simple Pairing mode is stored
in the inquiry cache for later use.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Simple Pairing feature is optional and needs to be enabled by the
host stack first. The Linux kernel relies on the Bluetooth daemon to
either enable or disable it, but at any time it needs to know the
current state of the Simple Pairing mode. So track any changes made
by external entities and store the current mode in the HCI device
structure.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

During the Simple Pairing process the HCI disconnect timer must be
disabled. The way to do this is by holding a reference count of the
HCI connection. The Simple Pairing process on both sides starts with
an IO Capabilities Request and ends with Simple Pairing Complete.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth specification supports the default link policy settings
on a per host controller basis. For every new connection the link
manager would then use these settings. It is better to use this instead
of bothering the controller on every connection setup to overwrite the
default settings.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The connection packet type can be changed after the connection has been
established and thus needs to be properly tracked to ensure that the
host stack has always correct and valid information about it.

On incoming connections the Bluetooth core switches the supported packet
types to the configured list for this controller. However the usefulness
of this feature has been questioned a lot. The general consent is that
every Bluetooth host stack should enable as many packet types as the
hardware actually supports and leave the decision to the link manager
software running on the Bluetooth chip.

When running on Bluetooth 2.0 or later hardware, don't change the packet
type for incoming connections anymore. This hardware likely supports
Enhanced Data Rate and thus leave it completely up to the link manager
to pick the best packet type.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth HCI commands are divided into logical OGF groups for
easier identification of their purposes. While this still makes sense
for the written specification, its makes the code only more complex
and harder to read. So instead of using separate OGF and OCF values
to identify the commands, use a common 16-bit opcode that combines
both values. As a side effect this also reduces the complexity of
OGF and OCF calculations during command header parsing.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To better support and handle eSCO links in the future a bunch of
constants needs to be added and some basic routines need to be
updated. This is the initial step.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For consistency with other skb data accessors, reducing the number of direct
accesses to skb->data.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In case of non-blocking connects it is possible that the last user
of an ACL link quits before the connection has been fully established.
This will lead to a race condition where the internal state of a
connection is closed, but the actual link has been established and is
active. In case of Bluetooth 1.2 and later devices it is possible to
call create connection cancel to abort the connect. For older devices
the disconnect timer will be used to trigger the needed disconnect.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The command complete event of the exit periodic inquiry command must
clear the HCI_INQUIRY flag and finish the HCI request.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch assigns the next free HCI device identifier to Bluetooth
devices based on the SDIO interface.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch introduces the automatic sniff mode feature. This allows
the host to switch idle connections into sniff mode to safe power.
Signed-off-by: NUlisses Furquim <ulissesf@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch introduces a quirk that allows the drivers to tell the host
to correct the SCO buffer size values.
Signed-off-by: NOlivier Galibert <galibert@pobox.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds the endian annotations to the Bluetooth core.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the handling of the extended inquiry responses and
inserts them into the inquiry cache.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The HCI page scan repetition mode change event contains the actual
page scan repetition mode for the remote device. It is the same
value that is received from an inquiry response and it can be used
to make further reconnections faster.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements a workaround for buggy Bluetooth 1.2 devices from
Silicon Wave. Their inquiry results with RSSI contain the page scan mode
field. This field was removed in the final Bluetooth 1.2 specification.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!