This patch moves the char and block major number definitions
to major.h to be with the rest of the major numbers.
While doing this, include major.h in the files that need it.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

A new type of partition with magic FCTY was found on Huawei E970:
46 43 54 59 4b 51 37 4e  41 42 31 38 41 32 39 30  |FCTYKQ7NAB18A290|
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Most of the bcm47xx devices use TRX format for storing kernel and some
partition like Squashfs or JFFS2. This is pretty flexible solution, CFE
(the bootloader) just writes (and later boots) TRX at some hardcoded
place and paritions can vary in the size.

However some devices don't use TRX format. Very recently we have
discovered ZTE H218N that has kernel and rootfs partitions at some
"random" places.

This patch allows Linux find a rootfs partition after installing custom
image with a CFE bootloader.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Handle return NULL in malloc.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

devm_kzalloc is device managed and simplifies the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

module_platform_driver simplifies the code by removing boiler plate.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

module_platform_driver simplifies the code by removing boiler
plate.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Some bright specification writers decided to write this in the ONFI spec
(from ONFI 3.0, Section 3.1):

  "The number of blocks and number of pages per block is not required to
  be a power of two. In the case where one of these values is not a
  power of two, the corresponding address shall be rounded to an
  integral number of bits such that it addresses a range up to the
  subsequent power of two value. The host shall not access upper
  addresses in a range that is shown as not supported."

This breaks every assumption MTD makes about NAND block/chip-size
dimensions -- they *must* be a power of two!

And of course, an enterprising manufacturer has made use of this lovely
freedom. Exhibit A: Micron MT29F32G08CBADAWP

  "- Plane size: 2 planes x 1064 blocks per plane
   - Device size: 32Gb: 2128 blockss [sic]"

This quickly hits a BUG() in nand_base.c, since the extra dimensions
overflow so we think it's a second chip (on my single-chip setup):

    ONFI param page 0 valid
    ONFI flash detected
    NAND device: Manufacturer ID: 0x2c, Chip ID: 0x44 (Micron MT29F32G08CBADAWP), 4256MiB, page size: 8192, OOB size: 744
    ------------[ cut here ]------------
    kernel BUG at drivers/mtd/nand/nand_base.c:203!
    Internal error: Oops - BUG: 0 [#1] SMP ARM
    [... trim ...]
    [<c02cf3e4>] (nand_select_chip+0x18/0x2c) from [<c02d25c0>] (nand_do_read_ops+0x90/0x424)
    [<c02d25c0>] (nand_do_read_ops+0x90/0x424) from [<c02d2dd8>] (nand_read+0x54/0x78)
    [<c02d2dd8>] (nand_read+0x54/0x78) from [<c02ad2c8>] (mtd_read+0x84/0xbc)
    [<c02ad2c8>] (mtd_read+0x84/0xbc) from [<c02d4b28>] (scan_read.clone.4+0x4c/0x64)
    [<c02d4b28>] (scan_read.clone.4+0x4c/0x64) from [<c02d4c88>] (search_bbt+0x148/0x290)
    [<c02d4c88>] (search_bbt+0x148/0x290) from [<c02d4ea4>] (nand_scan_bbt+0xd4/0x5c0)
    [... trim ...]
    ---[ end trace 0c9363860d865ff2 ]---

So to fix this, just truncate these dimensions down to the greatest
power-of-2 dimension that is less than or equal to the specified
dimension.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: <stable@vger.kernel.org>

This commit replaces the currently hardcoded buffer size, by a
dynamic detection scheme. First a small 256 bytes buffer is allocated
so the device can be detected (using READID and friends commands).

After detection, this buffer is released and a new buffer is allocated
to acommodate the page size plus out-of-band size.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Instead of setting info->dma each time a command is prepared,
we can move it after the DMA buffers are allocated.

This is more clear and it's the proper place to enable this, given
DMA cannot be turned on and off during runtime.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Micron N25Q512A is a spi flash memory with following features:
-64MB size, 1.8V, Mulitple I/O, 4KB Sector erase memory.
-Memory is organised as 1024(64KB) main sectors.
-Each sector is divided into 256 pages.
-Register set/Opcodes are similar to other N25Q family products.
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Use free_bch() instead of kfree() to free init_bch()
allocated data.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The loop that polls the status register waiting for an operation to complete
foolishly bases the timeout simply on the number of loop iterations that have
ocurred.  When I increased the processor clock speed, timeouts started to appear
for long block erasure operations.  This patch measures the timeout using
jiffies.
Signed-off-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

dev_err is preferred to printk.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

devm_kzalloc is device managed and makes code simpler.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Driver core will set the driver data to NULL upon detach or
probe failure.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

module_platform_driver removes boiler plate code and makes it
simpler.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Driver core will set the driver data to NULL upon detach or
probe failure.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

devm_kzalloc is device managed and makes code simpler.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Driver core will set the driver data to NULL upon detach
or probe failure.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

phram was 32-bit limited by design. Machines are growing up, but phram
module is still useful. Update it. The patch is bigger than minimum,
because simple_strtoul() is obsolete.

Tested on MIPS64 and compile-tested for PPC (32 bit).
Signed-off-by: NAlexander Sverdlin <alexander.sverdlin@nsn.com>
Reviewed-by: NJoern Engel <joern@logfs.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This flashchip is used in D-Link DIR-610 A1 router board
and maybe several others, yet is not kernel upstream.

So add support for it according to datasheet [0], making it easier
to support other boards using this flashchip in the future.

[0] http://www.esmt.com.tw/DB/manager/upload/F25L32PA.pdfSigned-off-by: NFlavio Silveira <fggs@terra.com.br>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Current code sets the mtd->type with MTD_NANDFLASH for both
SLC and MLC. So the jffs2 may supports the MLC nand, but in actually,
the jffs2 should not support the MLC.

This patch uses the nand_is_slc() to check the nand cell type,
and set the mtd->type with the right nand type.

After this patch, the jffs2 only supports the SLC nand.

The side-effect of this patch:
  Before this patch, the ioctl(MEMGETINFO) can only return with the
  MTD_NANDFLASH; but after this patch, the ioctl(MEMGETINFO) will
  return with the MTD_NANDFLASH for SLC, and MTD_MLCNANDFLASH for MLC.

  So the user applictions(such as mtd-utils) should also changes a little
  for this.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

We should not support the MLC nand for jffs2. So if the nand type is
MLC, we quit immediatly.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The current mtd_type_show() misses the MTD_MLCNANDFLASH case.
This patch adds the case for it, and also updates the ABI.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

The helper is for user applications, and it is just a copy of
the kernel helper: mtd_type_is_nand();
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

This helper detects that whether the mtd's type is nand type.

Now, it's clear that the MTD_NANDFLASH stands for SLC nand only.
So use the mtd_type_is_nand() to replace the old check method
to do the nand type (include the SLC and MLC) check.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

In current code, the MTD_NANDFLASH is used to represent both the SLC and
MLC. It is confusing to us.

By adding an explicit comment about these two macros, this patch makes it
clear that:
	MTD_NANDFLASH    : stands for SLC NAND,
	MTD_MLCNANDFLASH : stands for MLC NAND (including TLC).
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

When we use the ECC info which is get from the nand chip's datasheet,
we may have some freed oob area now.

This patch rewrites the gpmi_ecc_write_oob() to implement the ecc.write_oob().
We also update the comment for gpmi_hw_ecclayout.

Yes! We can support the JFFS2 for the SLC nand now.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>

Print out the cell information for nand chip.

(Since the message is too long, this patch also splits the log
with two separate pr_info())
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>