The current init code sets hiprilvl to 0 and maxhipri to 5.  According to the
specs those values are illegal on both G200 and G400.  It also causes
distortions on the TV-out at least when CRTC2 is in YUV mode as is the case
with DirectFB.  This patch resets both values to 0.
Signed-off-by: NVille Syrjälä <syrjala@sci.fi>
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

No point in spamming the logs with a message about xres rounding.
Signed-off-by: NVille Syrjl <syrjala@sci.fi>
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use the CACHEFLUSH register on all chip types.  The register is listed in all
other specs except 2064W.  However I have verified that the register does work
on a 2064W despite being marked reserved in the specs.  There were no
noticeable side effects after writing to the register.
Signed-off-by: NVille Syrjälä <syrjala@sci.fi>
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add new entries for Mystique AGP with the PCI ID 0x051e.

I don't actually have such boards but according to google they do exist.
Curiosly X.Org doesn't recognize that PCI ID.  And what's even more
interesting is that Matrox's own Windows drivers don't recognize it either.
After going through about a dozen different versions I did find one older
driver that does list this particular ID.  It is also listed in the pci.ids
file.

I'm not sure if non-220 AGP chips exist.  I left the chip revision check
intact for AGP chips nonetheless.
Signed-off-by: NVille Syrjl <syrjala@sci.fi>
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

wait_event_event_interruptible() uses a private wait queue entry so there's no
need for the caller to initialize one.
Signed-off-by: NVille Syrjl <syrjala@sci.fi>
Signed-off-by: NPetr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Here's the PCI ID for the ATI RN50 chip.
Signed-off-by: NJake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Convert i810fb, nvidiafb and savagefb to use the fb_find_best_display helper
when searching for the initial video mode.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add new helper, fb_find_best_display(), which will search the modelist for the
best mode for the attached display.  This requires an EDID block that is
converted to struct fb_monspecs and a private modelist.  The search will be
done in this manner:

- if 1st detailed timing is preferred, use that
- else if dimensions of the display are known, use that to estimate xres and
- else if modelist has detailed timings, use the first detailed timing
- else, use the very first entry from the modelist
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Rearrange mode database entries such that preferred timings are entered first,
and less preferred timings are entered last.  (Detailed, VESA,
established/standard).
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I converted the "rl" console font from the kbd utility to be a built-in font
for the framebuffer console, and I was wondering if you would be OK with
including it.  I've generated a font_rl.c file and related minor
modifications.  I find it's the most visually appealing of the kbd fonts which
is why I use it and selected it for conversion.  I believe the font is GPL'd.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix following compile error (From Kernel Bugzilla Bug 5427):

include/linux/console_struct.h:53: error: field `vt_mode' has incomplete type
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- The functions for reading the 1st and 2nd bus are essentially the same,
  except for the register.  Consolidate them all.

- According to Nicolas Boichat, there is an undocumented 3rd i2c bus for
  attaching daughter cards.  Add support for this.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

vesafb occassionally gets the size wrong when setting the mtrr.  When X or DRI
attempts to set the mtrr, it will fail due to range overlap significantly
affecting their performance.  Disable mtrr and let the user explicitly enable
it with the mtrr:n option.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initialise the .owner field, so that if the driver is built as a module, the
system has a link to the owner
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Currently the fb_find_nearest_mode() function finds a mode with screen
resolution closest to that described by the 'var' argument and with some
arbitrary refresh rate (eg.  in the following sequence of refresh rates: 70 60
53 85 75, 53 is selected).

This patch fixes the function so that it looks for the closest mode as far as
both resolution and refresh rate are concerned.  The function's first argument
is changed to fb_videomode so that the refresh rate can be specified by the
caller, as fb_var_screeninfo doesn't have any fields that could directly hold
this data.
Signed-off-by: NMichal Januszewski <spock@gentoo.org>
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use do {} while(0) for empty reverse_order() macro.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some EDID blocks set the flag "prefer first detailed timing" without providing
any detailed timing at all.  Clear this flag if the block does not provide
detailed timings.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Attached is a small patch which configures the correct memory clock and
timings on the Elsa Winner 2000 Office pm2 based card.  This is necessary when
the card is used on a platform which does not support PC style BIOS
initialization.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use MMIO registers instead of banging the VGA IO registers.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Reported by: Jean-Philippe Guérard (Bugzilla Bug 1782)

"I've tried with video=atyfb:debug and video=atyfb:debug,mode:1280x600, \
nomtrr.

In both case, the screen stays black, but seems divided into 4 vertical bands.
 Some white lines pop up randomly on each vertical band."

The problem is a combination of an incorrect xclk plus lack of timing
information.  The adapter is attached to an LCD device that can do 1280x600
(which is not a standard resolution).  The global mode database does not have
an entry for it.  Fortunately, the Video BIOS contains the complete timing
info for this display, however, atyfb is not making use of it.

Add support to get the timing information from the BIOS, if available.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix out-of-bounds bug.  The pseudopalette has room only for 16 entries, thus,
write only the first 16 entries to the pseudopalette.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove software clipping from imageblit, fillrect and copyarea.  Clipping is
not needed because the console layer assures that reads/writes doest not
happen beyond the extents of the framebuffer.  And software clipping tends to
hide bugs, if they do exist.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If machine has more than 1 driver installed, and they all drive the same
hardware, it's possible that the driver's fb_release() method will attempt to
restore the hardware state to the initial state.  This will leave the new
driver in an undefined state.  To prevent this problem, initialize the new
driver by calling fb_set_par() when the old driver is released by fbcon.

Signed-off-by: Antonino Daplas<adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Instead of manually filling up the fields in struct fb_var_screeninfo, use the
display_to_var() helper.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Lot's of redundant code scattered throughout fbcon.c.  Consolidate them all
into one function, fbcon_update_softback().
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

According to Jon Smirl, filling in the field fb_cursor with soft_cursor for
drivers that do not support hardware cursors is redundant.  The soft_cursor
function is usable by all drivers because it is just a wrapper around
fb_imageblit.  And because soft_cursor is an fbcon-specific hook, the file is
moved to the console directory.

Thus, drivers that do not support hardware cursors can leave the fb_cursor
field blank.  For drivers that do, they can fill up this field with their own
version.

The end result is a smaller code size.  And if the framebuffer console is not
loaded, module/kernel size is also reduced because the soft_cursor module will
also not be loaded.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Prevent spurious recompilations of the radeonfb driver when I2C/DDC support
is not included and i2c header files are modified.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add partial support for GMA900 within the i915GM chipset.
Signed-off-by: NScott MacKenzie <irrational@poboxes.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

nvidiafb didn't fully hook-up the code it borrowed from X for doing flat
panel dithering (this is useful for 6 bits panels).  This adds a driver
option to force it, and by default "reads" the current value from the chip
to get the firmware setting.  It significantly improves the quality of
images on the iMac G5 I have here (though the X driver doesn't yet "read"
the current value and defaults to 0, so you have to add Option "FBDither"
"true" to your X config file to get that, I'll try to fix X.org to "read"
the default unless specified asap).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

drivers/video/nvidia/nv_setup.c: In function `NVCommonSetup':
drivers/video/nvidia/nv_setup.c:408: warning: statement with no effect
drivers/video/nvidia/nv_setup.c:496: warning: statement with no effect
drivers/video/nvidia/nv_setup.c:504: warning: statement with no effect

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes nvifiafb mode setting code to be closer to what the X
driver does, which actually makes it work on the 5200FX I have access to.
It also fix the routine that gets the EDID from Open Firmware on PPC, it
was broken in various ways and would crash at boot.  Compared to the patch
I posted to linux-fbdev last week, this one just changes a printk to be
closer to the other ones in the driver.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Arrange frame buffer menu:
- puts all Epson drivers together
- removes split of FB_PXA and FB_PXA_PARAMETERS by FB_W100
- results in PXA, W100, Epson, S3C2410, & Virtual FB drivers being
  presented at the same menu level as all other FB drivers
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: N"Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Frame buffer driver help text changes:
- Move S3 Trio next to S3 Savage;
- add or clarify help text for several FB drivers;
- add help text for FB console;
- add help text for bootup logos;
Acked-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If an RPC socket is serving multiple programs, then the pg_authenticate of
the first program in the list is called, instead of pg_authenticate for the
program to be run.

This does not cause a problem with any programs in the current kernel, but
could confuse future code.

Also set pg_authenticate for nfsd_acl_program incase it ever gets used.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There are a couple of tests which could possibly be confused by extremely
large numbers appearing in 'xdr' packets.  I think the closest to an exploit
you could get would be writing random data from a free page into a file - i.e.
 leak data out of kernel space.

I'm fairly sure they cannot be used for remote compromise.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Provide a file in the NFSD filesystem that allows setting and querying of
which version of NFS are being exported.  Changes are only allowed while no
server is running.
Signed-off-by: NSteve Dickson <steved@redhat.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Most files in the nfsd filesystems are transaction files.  You write a
request, and read a response.

For some (e.g.  'threads') it makes sense to just be able to read and get the
current value.

This functionality did exist but was broken recently when someone modified
nfsctl.c without going through the maintainer.  This patch fixes the
regression.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is a somewhat cosmetic fix to keep the SpecFS validation test from
complaining.

SpecFS want's to try chmod on symlinks, and ext3 and reiser (at least) return
ENOTSUPP.

Probably both sides are being silly, but it is easiest to simply make it a
non-issue and filter out chmod requests on symlinks at the nfsd level.
Signed-off-by: NOlaf Kirch <okir@suse.de>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix the warning "Debug: sleeping function called from invalid context at
include/asm/semaphore.h:102" that the zr36067 driver emits every time an
application using JPEG capture starts up (e.g.  mjpegtools' lavrec).

The warning is harmless, but clogs up the dmesg output.  This was logged as
bugzilla #5403.  (Thanks to Christian Casteyde for helping me in fixing
this long-standing annoyance.)
Signed-off-by: NRonald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

  - cleanup source
  - remove nonfunctional code parts
Signed-off-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>