instead of having infinite loop and always checking
timeout value as a break condition, we can just
decrement timeout inside while's condition.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

We don't need the extra %s when command fails.
Let's remove it
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This will make it more human-friendly to read trace
output from dwc3.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

I really thought this would be useful, but as it
turns out, it creates more problems than fixes. The
amount of times we had to fix this because some
other commit shuffled things around and ended up
regressing this tiny little string manupulation...

Might as well remove it, since it has a negligible
added benefit.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Improve trb tracing by showing trb flags, interrupts
trb type.

trb flags:
- h - hardware owner of descriptor
- l - last TRB
- c - chain buffers
- s - continue on short packet

interrupt flags:
- s - interrupt on short packet
- c - interrupt on complete

Capital letter means that bit is set, while
lowercase letter means bit is cleared.
Signed-off-by: NJanusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This will allow us to process several endpoints at a
time by making sure that we lock only shared
resources.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Allow for dwc3-pci to reach D3 and enable pm_runtime
by providing dummy PM hooks. Without them, PCI
subsystem won't put device to D3.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

this patch implements the most basic pm_runtime
support for dwc3. Whenever USB cable is dettached,
then we will allow core to runtime_suspend.

Runtime suspending will involve completely tearing
down event buffers and require a full soft-reset of
the IP.

Note that a further optimization could be
implemented once we decide to support hibernation,
which is to allow runtime_suspend with cable
connected when bus is in U3. That's subject to a
separate patch, however.
Tested-by: NBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

when we call dwc3_gadget_giveback(), we end up
releasing our controller's lock. Another thread
could get scheduled and disable the endpoint,
subsequently setting dep->endpoint.desc to NULL.

In that case, we would end up dereferencing a NULL
pointer which would result in a Kernel Oops. Let's
avoid the problem by simply returning early if we
have a NULL descriptor.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

commit f3af3651 ("usb: dwc3: gadget: always
enable IOC on bulk/interrupt transfers") ended up
regressing Isochronous endpoints by clearing
DWC3_EP_BUSY flag too early, which resulted in
choppy audio playback over USB.

Fix that by partially reverting original commit and
making sure that we check for isochronous endpoints.

Fixes: f3af3651 ("usb: dwc3: gadget: always enable IOC
		on bulk/interrupt transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: NKonrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: NRafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

As a micro-power optimization, let's only resume the
USB2 PHY if we're working on <=HIGHSPEED. If we're
gonna work on SUPERSPEED or SUPERSPEED+, there's no
point in resuming the USB2 PHY.

Fixes: 2b0f11df ("usb: dwc3: gadget: clear SUSPHY bit before ep cmds")
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

by holding gadget's IRQ number in dwc->irq_gadget,
it'll be simpler to free_irq() and disable the IRQ
in case an IRQ fires while we are runtime suspended.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

now that we have re-factored dwc3_core_init() and
dwc3_core_exit() we can use them for suspend/resume
operations.

This will help us avoid some common mistakes when
patching code when we have duplicated pieces of code
doing the same thing.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The idea of this patch is for dwc3_core_init() to
abstract all the details about how to initialize
dwc3 and dwc3_core_exit() to do the same for
teardown.

With this, we can simplify suspend/resume operations
by a large margin and always know that we're going
to start dwc3 from a known starting point.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

this patch is in preparation for some further
re-factoring in dwc3 initialization. No functional
changes.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

By adding a pointer to endpoint registers' base
address, we can avoid using our controller-wide
struct dwc3 pointer for everything. At some point
this will allow us to have per-endpoint locks which
will, in turn, let us queue requests to separate
endpoints in parallel.

Because of this change our debugfs interface and io
accessors need to be changed accordingly.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

In all call sites of dwc3_send_gadget_ep_cmd() we
already had a valid dep pointer, so instead of
passing dwc and dep->number, which would be used to
fetch the same pointer we already had, just pass dep
directly.

In other words, we're changing:

	struct dwc3_ep *dep = dwc[dep->number];

to just passing struct dwc3_ep *dep as argument.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Instead of using burst size to configure NUMP, we
should be using RxFIFO Size instead. DWC3 is smart
enough to know that it shouldn't burst in case burst
size is 0.
Reported-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

To aid code readability, we're gonna split
__dwc3_gadget_kick_transfer() into its constituent
parts: scatter gather and linear buffers.

That way, it's easier to follow the code and focus
debug effort when one or the other fails.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Instead of returning -EINVAL when someone calls
__dwc3_gadget_wakeup() in speeds > highspeed, let's
return 0. There are no problems for the driver for
calling it in superspeed as we cleanly just return.

This avoids an annoying WARN_ONCE() always
triggering during superspeed enumeration with LPM
enabled.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

When we send an endpoint command, we want that to
complete as soon as possible, so let's remove the
unnecessary udelay(1) call.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

sg_is_last() and list_is_last() will encode the
required information for the driver to make
decisions WRT CHN and LST bits.

While at that, also replace '1' with 'true' for
consistency.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

as it turns out, we don't need the extra 'start_new'
argument as that can be inferred from DWC3_EP_BUSY
flag.

Because of that, we can simplify
__dwc3_gadget_kick_transfer() by quite a bit, even
allowing us to prepare more TRBs unconditionally.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

If we're updating transfers, we can also prepare as
many TRBs as we can fit in the ring. Let's start
doing that.

This patch 'solves' a limitation of how many TRBs we
can prepare when we're getting close the end of the
ring. Instead driver to prepare only up to end of
the ring, we check if we have space to wrap around
the ring properly.

Note that this only happens when our enqueue and
dequeue pointers are equal (which is the case for
bulk endpoints after an XferComplete event).
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

that macro is unnecessary and just adds pointless
obfuscation. Let's remove it.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Instead of trying hard to stay connected to the
host, it's best (and far easier) to disconnect from
the host already.

Anything relying on KEEP_CONNECT will just have that
ignored, but we don't have proper hibernation
implementation yet, so there are no regressions.

In any case, hibernation is only useful for runtime
PM, not system sleep.

While at that, also remove dwc3.dcfg which has been
rendered unnecessary.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

we will be re-using it for suspend/resume, so
instead of duplicating code, let's just re-factor
the functions so they can be re-used.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The PLX USB2380 is a PCIe version of the NET2280 and behaves more like the
USB338x but without the USB3.0 superspeed support.

This was tested with g_ether, g_serial, g_mass_storage on a Gateworks
Ventana GW2383.

Cc: Justin DeFields <justindefields@gmail.com>
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

With a default size of 16kiB and with maximum of 32
buffers, we can transfer up to 512kiB, however Linux
can transfer up to 1MiB in a single mass storage
block transfer to USB3 storage devices.

Because of this, 1MiB block transfers end up being
slower than 512kiB block transfers. Let's increase
maximum number of storage buffers to a ridiculous
amount (256) so that anybody wanting to test maximum
achievable throughput can do so.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

valid range for storage buffers is encoded in
Kconfig already. Instead of checking again, let's
drop fsg_num_buffers_validate() altogether.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

It's annoying to constantly see the same "Not yet implemented" message
over and over with nothing able to be done about it, so rate limit it
for now to keep user's logs "clean".
Reported-by: NLars Täuber <lars.taeuber@web.de>
Tested-by: NLars Täuber <lars.taeuber@web.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The comment is wrong, glue is devm_kzalloc-ed mem attached to the
"allwinner,sun4i-a10-musb" compatible platform-dev. Where as
glue->musb_pdev is a newly created "musb-hdrc" platform-dev.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Stop using the return value of platform_device_register_full() to get to
the struct musb in sunxi_musb_work(). If a gadget has been registered
(insmod-ed) before the musb driver, then musb_start will get called
from the musb_core probe function and sunxi_musb_work() may run before
platform_device_register_full() has returned.

Instead store a pointer to struct musb in struct sunxi_glue when
sunxi_musb_enable gets called. Note that sunxi_musb_enable always gets
called before sunxi_musb_work() can run.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch protects system from crashing at shutdown in
cases where usb host is not added yet from OTG controller driver.
As ehci_setup() not done yet, so stop accessing registers or
variables initialized as part of ehci_setup().

The use case is simple, for boards like DB410c where the usb host
or device functionality is decided based on the micro-usb cable
presence. If the board boots up with micro-usb connected, the
OTG driver like echi-msm would not add the usb host by default.
However a system shutdown would go and access registers and
uninitialized variables, resulting in below crash.

Unable to handle kernel NULL pointer dereference at virtual address
 00000008
pgd = ffffffc034581000
[00000008] *pgd=0000000000000000, *pud=0000000000000000
CPU: 2 PID: 1957 Comm: reboot Not tainted 4.6.0+ #99
task: ffffffc034bc0000 ti: ffffffc0345cc000 task.ti: ffffffc0345cc000
PC is at ehci_halt+0x54/0x108
LR is at ehci_halt+0x38/0x108
pc : [<ffffff800869837c>] lr : [<ffffff8008698360>] pstate: a00001c5
sp : ffffffc0345cfc60
x29: ffffffc0345cfc60 x28: ffffffc0345cc000
x27: ffffff8008a4d000 x26: 000000000000008e
x25: ffffff8008d86cb0 x24: ffffff800908b040
x23: ffffffc036068870 x22: ffffff8009d0a000
x21: ffffffc03512a410 x20: ffffffc03512a410
x19: ffffffc03512a338 x18: 00000000000065ba
x17: ffffff8009b16b80 x16: 0000000000000003
x15: 00000000000065b9 x14: 00000000000065b6
x13: 0000000000000000 x12: 0000000000000000
x11: 000000000000003d x10: ffffffc0345cf9e0
x9 : 0000000000000001 x8 : ffffffc0345cc000
x7 : ffffff8008698360 x6 : 0000000000000000
x5 : 0000000000000080 x4 : 0000000000000001
x3 : 0000000000000000 x2 : 0000000000000000
x1 : 0000000000000008 x0 : ffffffc034bc0000

Process reboot (pid: 1957, stack limit = 0xffffffc0345cc020)
Stack: (0xffffffc0345cfc60 to 0xffffffc0345d0000)
fc60: ffffffc0345cfc90 ffffff8008698448 ffffffc03512a338 ffffffc03512a338
fc80: ffffffc03512a410 ffffff8008a3bbfc ffffffc0345cfcc0 ffffff8008698548
fca0: ffffffc03512a338 ffffffc03512a000 ffffffc03512a410 ffffff8009d0a000
fcc0: ffffffc0345cfcf0 ffffff800865d2bc ffffffc036068828 ffffffc036068810
fce0: ffffffc036003810 ffffff800853f43c ffffffc0345cfd00 ffffff800854338c
fd00: ffffffc0345cfd10 ffffff800853f45c ffffffc0345cfd60 ffffff80080e0f48
fd20: 0000000000000000 0000000001234567 ffffff8008f8c000 ffffff8008f8c060
fd40: 0000000000000000 0000000000000015 0000000000000120 ffffff80080e0f30
fd60: ffffffc0345cfd70 ffffff80080e1020 ffffffc0345cfd90 ffffff80080e12fc
fd80: 0000000000000000 0000000001234567 0000000000000000 ffffff8008085e70
fda0: 0000000000000000 0000005592905000 ffffffffffffffff 0000007f79daf1cc
fdc0: 0000000000000000 0000000000000000 0000007ffcbb1198 000000000000000a
fde0: 00000055928d3f58 0000000000000001 ffffffc034900000 00000000fffffffe
fe00: ffffffc034900000 0000007f79da902c ffffffc0345cfe40 ffffff800820af38
fe20: 0000000000000000 0000007ffcbb1078 ffffffffffffffff ffffff80081e9b38
fe40: ffffffc0345cfe60 ffffff80081eb410 ffffffc0345cfe60 ffffff80081eb444
fe60: ffffffc0345cfec0 ffffff80081ec4f4 0000000000000000 0000007ffcbb1078
fe80: ffffffffffffffff 0000000000000015 ffffffc0345cfec0 0000007ffcbb1078
fea0: 0000000000000002 000000000000000a ffffffffffffffff 0000000000000000
fec0: 0000000000000000 ffffff8008085e70 fffffffffee1dead 0000000028121969
fee0: 0000000001234567 0000000000000000 ffffffffffffffff 8080800000800000
ff00: 0000800000808080 0000007ffcbb10f0 000000000000008e fefeff54918cb8c7
ff20: 7f7f7f7fffffffff 0101010101010101 0000000000000010 0000000000000000
ff40: 0000000000000000 0000007f79e33588 0000005592905eb8 0000007f79daf1b0
ff60: 0000007ffcbb1340 0000005592906000 0000005592905000 0000005592906000
ff80: 0000005592907000 0000000000000002 0000007ffcbb1d98 0000005592906000
ffa0: 00000055928d2000 0000000000000000 0000000000000000 0000007ffcbb1aa0
ffc0: 00000055928b819c 0000007ffcbb1aa0 0000007f79daf1cc 0000000000000000
ffe0: fffffffffee1dead 000000000000008e 05ef555057155555 d555544d55d775d3
Call trace:
Exception stack(0xffffffc0345cfaa0 to 0xffffffc0345cfbc0)
Set corner to 6
faa0: ffffffc03512a338 ffffffc03512a410 ffffffc0345cfc60 ffffff800869837c
fac0: ffffff8008114210 0000000100000001 ffffff8009ce1b20 ffffff8009ce5f20
fae0: ffffffc0345cfb80 ffffff80081145a8 ffffffc0345cfc10 ffffff800810b924
fb00: ffffffc0345cc000 00000000000001c0 ffffffc03512a410 ffffff8009d0a000
fb20: ffffffc036068870 ffffff800908b040 ffffff8008d86cb0 000000000000008e
fb40: ffffffc034bc0000 0000000000000008 0000000000000000 0000000000000000
fb60: 0000000000000001 0000000000000080 0000000000000000 ffffff8008698360
fb80: ffffffc0345cc000 0000000000000001 ffffffc0345cf9e0 000000000000003d
fba0: 0000000000000000 0000000000000000 00000000000065b6 00000000000065b9
[<ffffff800869837c>] ehci_halt+0x54/0x108
[<ffffff8008698448>] ehci_silence_controller+0x18/0xcc
[<ffffff8008698548>] ehci_shutdown+0x4c/0x64
[<ffffff800865d2bc>] usb_hcd_platform_shutdown+0x1c/0x24
[<ffffff800854338c>] platform_drv_shutdown+0x20/0x28
[<ffffff800853f45c>] device_shutdown+0xf4/0x1b0
[<ffffff80080e0f48>] kernel_restart_prepare+0x34/0x3c
[<ffffff80080e1020>] kernel_restart+0x14/0x74
[<ffffff80080e12fc>] SyS_reboot+0x110/0x21c
[<ffffff8008085e70>] el0_svc_naked+0x24/0x28
Code: 53001c42 350000a2 d5033e9f 91002021 (b9000022)

Fixes 4bb3cad7 ("usb: host: ehci-msm: Register usb shutdown function")
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: NPramod Gurav <pramod.gurav@linaro.org>
Tested-by: NAndy Gross <andy.gross@linaro.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a suspend/resume issue where the driver is blindly
calling ehci_suspend/resume functions when the ehci hasn't been setup.
This results in a crash during suspend/resume operations.
Signed-off-by: NAndy Gross <andy.gross@linaro.org>
Tested-by: NPramod Gurav <pramod.gurav@linaro.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Starting with commit 0b52297f ("reset: Add support for shared reset
controls") there is a reference count for reset control assertions. The
goal is to allow resets to be shared by multiple devices and an assert
will take effect only when all instances have asserted the reset.

In order to preserve backwards-compatibility, all reset controls become
exclusive by default. This is to ensure that reset_control_assert() can
immediately assert in hardware.

However, this new behaviour triggers the following warning in the EHCI
driver for Tegra:

[    3.365019] ------------[ cut here ]------------
[    3.369639] WARNING: CPU: 0 PID: 1 at drivers/reset/core.c:187 __of_reset_control_get+0x16c/0x23c
[    3.382151] Modules linked in:
[    3.385214] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.6.0-rc6-next-20160503 #140
[    3.392769] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[    3.399046] [<c010fa50>] (unwind_backtrace) from [<c010b120>] (show_stack+0x10/0x14)
[    3.406787] [<c010b120>] (show_stack) from [<c0347dcc>] (dump_stack+0x90/0xa4)
[    3.414007] [<c0347dcc>] (dump_stack) from [<c011f4fc>] (__warn+0xe8/0x100)
[    3.420964] [<c011f4fc>] (__warn) from [<c011f5c4>] (warn_slowpath_null+0x20/0x28)
[    3.428525] [<c011f5c4>] (warn_slowpath_null) from [<c03cc8cc>] (__of_reset_control_get+0x16c/0x23c)
[    3.437648] [<c03cc8cc>] (__of_reset_control_get) from [<c0526858>] (tegra_ehci_probe+0x394/0x518)
[    3.446600] [<c0526858>] (tegra_ehci_probe) from [<c04516d8>] (platform_drv_probe+0x4c/0xb0)
[    3.455029] [<c04516d8>] (platform_drv_probe) from [<c044fe78>] (driver_probe_device+0x1ec/0x330)
[    3.463892] [<c044fe78>] (driver_probe_device) from [<c0450074>] (__driver_attach+0xb8/0xbc)
[    3.472320] [<c0450074>] (__driver_attach) from [<c044e1ec>] (bus_for_each_dev+0x68/0x9c)
[    3.480489] [<c044e1ec>] (bus_for_each_dev) from [<c044f338>] (bus_add_driver+0x1a0/0x218)
[    3.488743] [<c044f338>] (bus_add_driver) from [<c0450768>] (driver_register+0x78/0xf8)
[    3.496738] [<c0450768>] (driver_register) from [<c010178c>] (do_one_initcall+0x40/0x170)
[    3.504909] [<c010178c>] (do_one_initcall) from [<c0c00ddc>] (kernel_init_freeable+0x158/0x1f8)
[    3.513600] [<c0c00ddc>] (kernel_init_freeable) from [<c0810784>] (kernel_init+0x8/0x114)
[    3.521770] [<c0810784>] (kernel_init) from [<c0107778>] (ret_from_fork+0x14/0x3c)
[    3.529361] ---[ end trace 4bda87dbe4ecef8a ]---

The reason is that Tegra SoCs have three EHCI controllers, each with a
separate reset line. However the first controller contains UTMI pads
configuration registers that are shared with its siblings and that are
reset as part of the first controller's reset. There is special code in
the driver to assert and deassert this shared reset at probe time, and
it does so irrespective of which controller is probed first to ensure
that these shared registers are reset before any of the controllers are
initialized. Unfortunately this means that if the first controller gets
probed first, it will request its own reset line and will subsequently
request the same reset line again (temporarily) to perform the reset.
This used to work fine before the above-mentioned commit, but now
triggers the new WARN.

Work around this by making sure we reuse the controller's reset if the
controller happens to be the first controller.

Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.

Commit a47cc24c ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.

This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.

Fixes: a47cc24c ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

parport subsystem has introduced parport_del_port() to delete a port
when it is going away. Without parport_del_port() the registered port
will not be unregistered.
To reproduce and verify the error:
Command to be used is : ls /sys/bus/parport/devices
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and the command still shows "parport0".
4) Attach the device again and we get "parport1".

With the patch applied:
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and there is no output as "parport0" is now
removed.
4) Attach device again to get "parport0" again.

Cc: <stable@vger.kernel.org> # 4.2+
Signed-off-by: NSudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.

This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.

The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.

Fix ed_schedule to update ED state only on successful return.
Signed-off-by: NMichal Pecio <michal.pecio@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: NAndrew Goodbody <andrew.goodbody@cambrionix.com>
Cc: stable@vger.kernel.org
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>