Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS to simplify the code.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS to simplify the code.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

smatch rightfully says:

drivers/i2c/muxes/i2c-mux-pinctrl.c:175 i2c_mux_pinctrl_probe() warn: inconsistent indenting
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The lock is taken while reading two registers. On RT the first lock is
taken in hard irq where it might sleep and in the threaded irq.
The threaded irq runs in oneshot mode so the hard irq does not run until
the thread the completes so there is no reason to grab the lock.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
[grygorii.strashko@ti.com: drop locking from isr completely and remove
lock field from struct omap_i2c_dev]
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Share the ACPI companion for the platform device with the
i2c adapter, so that the adapter has access to the properties
defined in ACPI tables.
Signed-off-by: NIrina Tirdea <irina.tirdea@intel.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

All i2c mux users are using an explicit i2c mux core, drop support
for implicit i2c mux cores.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Tested-by: NAntti Palosaari <crope@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Tested-by: NAntti Palosaari <crope@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: NAntti Palosaari <crope@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: NAntti Palosaari <crope@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Acked-by: NJonathan Cameron <jic23@kernel.org>
Tested-by: NCrestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.

Add a mask to handle the case where not all child adapters should
cause a mux deselect to happen, now that there is a common deselect op
for all child adapters.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

All i2c-muxes have a parent adapter and one or many child
adapters. A mux also has some means of selection. Previously,
this was stored per child adapter, but it is only needed
to keep track of this per mux.

Add an i2c mux core, that keeps track of this consistently.

Also add some glue for users of the old interface, which will
create one implicit mux core per child adapter.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Tested-by: NAntti Palosaari <crope@iki.fi>
Tested-by: NCrestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

We cannot expect msleep(1) to actually sleep for a period shorter than
20 ms. Replace all calls to msleep() with usleep_range().
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The second check for I2C_FUNC_I2C is reduntant, so remove it.
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
[wsa: reworded commit message]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Switch to the new generic functions: i2c_parse_fw_timings().
Signed-off-by: NDavid Wu <david.wu@rock-chips.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Remove superfluous check and stray newline.
Signed-off-by: NJan Glauber <jglauber@cavium.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add helper functions for control, data and status register access.
This simplifies the code and makes the purpose of the register
access clearer.
Signed-off-by: NJan Glauber <jglauber@cavium.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Rename the [read|write]_sw functions to make it clearer they access
the TWSI registers.
Signed-off-by: NJan Glauber <jglauber@cavium.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

No functional change, just moving the functions upward in
preparation of improving the recovery.
Signed-off-by: NJan Glauber <jglauber@cavium.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Convert the adapter timeout to 2 ms independently of depending on CONFIG_HZ.
CONFIG_HZ is 100 for MIPS Cavium-Octeon so the timeout value is not changed.

Also set retries to 5 to improve robustness.
Signed-off-by: NJan Glauber <jglauber@cavium.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Enable multi-master mode in I2C_CNFG reg based on hw features.
Using single/multi-master mode bit introduced for Tegra210,
whereas multi-master mode is enabled by default in HW for T124 and
earlier Tegra SOC. Enabling this bit doesn't explicitly start
treating the bus has having multiple masters, but will start
checking for arbitration lost and reporting when it occurs.

The Tegra210 I2C controller supports single/multi master mode.
Add chipdata for Tegra210 and its compatibility string so that
Tegra210 will select data that enables multi master mode correctly.

Do below prerequisites for multi-master bus if "multi-master"
dt property entry is added.
 1. Enable 1st level clock always set.
 2. Disable 2nd level clock gating (slcg which
    is supported from T124 SOC and later chips)
Signed-off-by: NShardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allow runtime PM so that PM and PCI core can put the device into low-power
state when idle and resume it back when needed in those platforms that
support PM for i801 device.

Enable also autosuspend with 1 second delay in order to not needlessly
toggle power state on and off if there are multiple transactions during
short time.

Device is resumed at the beginning of bus access and marked idle ready
for autosuspend at the end of it.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Stop using legacy PCI PM support and convert to standard dev_pm_ops.
This provides more straightforward path to add runtime PM.

While at it remove explicit PCI power state control and configuration space
save/restore as the PCI core does it.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

When using a certain I2C device with runtime PM enabled on
a certain I2C bus adaper the following happens:

struct amba_device *foo
   \
   struct i2c_adapter *bar
      \
      struct i2c_client *baz

The AMBA device foo has its device PM struct set to ignore
children with pm_suspend_ignore_children(&foo->dev, true).
This makes runtime PM work just fine locally in the driver:
the fact that devices on the bus are suspended or resumed
individually does not affect its operation, and the hardware
does not power up unless transferring messages.

However this child ignorance property is not inherited into
the struct i2c_adapter *bar.

On system suspend things will work fine.

On system resume the following annoying phenomenon occurs:

- In the pm_runtime_force_resume() path of
  struct i2c_client *baz, pm_runtime_set_active(&baz->dev); is
  eventually called.

- This becomes __pm_runtime_set_status(&baz->dev, RPM_ACTIVE);

- __pm_runtime_set_status() detects that RPM state is changed,
  and checks whether the parent is:
  not active (RPM_ACTIVE) and not ignoring its children
  If this happens it concludes something is wrong, because
  a parent that is not ignoring its children must be active
  before any children activate.

- Since the struct i2c_adapter *bar does not ignore
  its children, the PM core thinks that it must indeed go
  online before its children, the check bails out with
  -EBUSY, i.e. the i2c_client *baz thinks it can't work
  because it's parent is not online, and it respects its
  parent.

- In the driver the .resume() callback returns -EBUSY from
  the runtime_force_resume() call as per above. This leaves
  the device in a suspended state, leading to bad behaviour
  later when the device is used. The following debug
  print is made with an extra printg patch but illustrates
  the problem:

[   17.040832] bh1780 2-0029: parent (i2c-2) is not active
               parent->power.ignore_children = 0
[   17.040832] bh1780 2-0029: pm_runtime_force_resume:
               pm_runtime_set_active() failed (-16)
[   17.040863] dpm_run_callback():
               pm_runtime_force_resume+0x0/0x88 returns -16
[   17.040863] PM: Device 2-0029 failed to resume: error -16

Fix this by letting all struct i2c_adapter:s ignore their
children: i2c children have no business doing keeping
their parents awake: they are completely autonomous
devices that just use their parent to talk, a usecase
which must be power managed in the host on a per-message
basis.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>