This removes the legacy (non-mq) IO path for SCSI.

Cc: linux-scsi@vger.kernel.org
Acked-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMing Lei <ming.lei@redhat.com>
Reviewed-by: NOmar Sandoval <osandov@fb.com>
Acked-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Currently, on each io completion, the stats update routine indiscriminately
holds a lock. While holding the adapter-wide lock, checks are made to check
whether status are being tracked. When disabled (the default), the locking
wasted a lot of cycles.

Check for stats enablement before taking the lock.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

On io completion, the driver is taking an adapter wide lock and nulling the
scsi command back pointer.  The nulling of the back pointer is to signify the
io was completed and the scsi_done() routine was called.  However, the routine
makes no check to see if the abort routine had done the same thing and
possibly nulled the pointer. Thus it may doubly-complete the io.

Make the following mods:

- Check to make sure forward progress (call scsi_done()) only happens if the
  command pointer was non-null.

- As the taking of the lock, which is adapter wide, is very costly on a system
  under load, null the pointer using an xchg operation rather than under lock.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Smatch complains about this code:

    drivers/scsi/lpfc/lpfc_scsi.c:1053 lpfc_get_scsi_buf_s4()
    warn: variable dereferenced before check 'lpfc_cmd' (see line 1039)

Fortunately the NULL check isn't required so I have removed it.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Performance is affected when target queue depth is tracked.  An atomic
counter is incremented on the submission path which competes with it being
decremented on the completion path.  In addition, multiple CPUs can
simultaniously be manipulating this counter for the same ndlp.

Reduce the overhead by only performing the target increment/decrement when
the target queue depth is less than the overall adapter depth, thus is
actually meaningful.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Enabling list_debug showed the drivers txcmplq was suffering list
corruption. The systems will eventually crash because the iocb free list
gets crossed linked with the prings txcmplq.  Most systems will run for a
while after the corruption, but will eventually crash when a scsi eh reset
occurs and the txcmplq is attempted to be flushed. The flush gets stuck in
an endless loop.

The problem is the abort handler does not hold the sli4 ring lock while
validating the IO so the IO could complete while the driver is still
preping the abort.  The erroneously generated abort, when it completes, has
pointers to the original IO that has already completed, and the IO
manipulation (for the second time) corrupts the list.

Correct by taking the ring lock early in the abort handler so the erroneous
abort won't be sent if the io has/is completing.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove the ScsiResult macro and open code it on all call sites.

This will make subsequent refactoring in this area easier.
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Reviewed-by: NBart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

A race condition between the context of devloss timeout handler and I/O
completion caused devloss timeout handler de-referencing pointer that had
been released.

Added the check in lpfc_sli_validate_fcp_iocb() on LPFC_IO_ON_TXCMPLQ to
capture the race condition of I/O completion and devloss timeout handler
attemption for aborting the I/O. Also, added check on lpfc_cmd->rdata
pointer before de-referenceing lpfc_cmd->rdata->pnode.

Also, added protection in lpfc_sli_abort_iocb() routine on driver performed
FCP I/O FLUSHING already under way before proceeding to aborting I/Os.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The PBDE optimizations aren't supported in all firmware revs.

Make optimizations configurable in case there's a side effect on old
firmware.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix small formatting and wording nits in Broadcom copyright header
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When running loads that generated aborts, io errors where seen.  Turns
out the abort requests where not placed on the proper WQ resulting in
the errors. Closer inspection inspection of this error also showed
improper spinlock api use.

Correct the WQ selection policy for the abort requests.  Correct
spin_lock/spin_lock_irq/spin_lock_irqsave usage.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The max_scsicmpl_time parameter can be used to perform scsi cmd queue
depth mgmt based on io completion time: the queue depth is reduced to
make completion time shorter. However, as soon as an io completes and
the completion time is within limits, the code immediately bumps the
queue depth limit back up to the target queue depth. Thus the procedure
restarts, effectively limiting the usefulness of adjusting queue depth
to help completion time.

This patch makes the following changes:

 - Removes the code at io completion that resets the queue depth as soon
   as within limits.

 - As the code removed was where the target queue depth was first
   applied, change target queue depth application so that it occurs when
   the parameter is changed.

 - Makes target queue depth a standard parameter: both a module
   parameter and a sysfs parameter.

 - Optimizes the command pending count by using atomics rather than
   locks.

 - Updates the debugfs nodelist stats to allow better debugging of
   pending command counts.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver fails to allocate command buffers in the routine
lpfc_new_scsi_buf_s4

There is an inconsistency between lpfc_mem_alloc(), where the
phba->lpfc_sg_dma_buf_pool is created, and lpfc_new_scsi_buf_s4(),
when we allocate a buffer from the pool and check the alignment.  The
alignment should be on a page boundary, based on LPFC_SLI3_BG_ENABLED in
sli3_options, for both cases.

Fix by explicitly tracking sli4 vs sli3 and BG options.  The result is that
phba->cfg_sg_dma_buf_size is now set correctly for SLI-4.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The current driver isn't taking advantage of a performance hint whereby
the initial data buffer descriptor can be placed in the WQE as well as
the SGL.

Add the logic to detect support for the feature and to use it when
supported.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updated Copyright in files updated 11.4.0.7
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently, write underruns (mismatch of amount transferred vs scsi
status and its residual) detected by the adapter are not being flagged
as an error. Its expected the target controls the data transfer and
would appropriately set the RSP values.  Only read underruns are treated
as errors.

Revise the SCSI error handling to treat write underruns as an error as
well.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Make the attribute writeable.

Remove the ramp up to logic as its unnecessary, simply set depth.  Add
debug message if depth changed, possibly reducing limit, yet our
outstanding count has yet to catch up with it.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API. It also updates
some comments, accordingly.
Signed-off-by: NRomain Perier <romain.perier@collabora.com>
Reviewed-by: NPeter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NDmitry Monakhov <dmonakhov@openvz.org>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

NVME FC counters don't reflect actual results

Since counters are not atomic, or protected by a lock, the values often
get screwed up.

Make them atomic, like NVMET.  Fix up sysfs and debugfs display
accordingly Added Outstanding IOs to stats display
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Christoph's prior patch missed the template for the sli3 adapters,
which is now the "no host reset" template. Add the transport
eh_timed_out handler to the no host reset template
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

A previous change unilaterally removed the hba reset entry point
from the sli3 host template. This was done to allow tape devices
being used for back up from being removed. Why was this done ?
When there was non-responding device on the fabric, the error
escalation policy would escalate to the reset handler. When the
reset handler was called, it would reset the adapter, dropping
link, thus logging out and terminating all i/o's - on any target.
If there was a tape device on the same adapter that wasn't in
error, it would kill the tape i/o's, effectively killing the
tape device state.  With the reset point removed, the adapter
reset avoided the fabric logout, allowing the other devices to
continue to operate unaffected. A hack - yes. Hint: we really
need a transport I_T nexus reset callback added to the eh process
(in between the SCSI target reset and hba reset points), so a
fc logout could occur to the one bad target only and stop the error
escalation process.

This patch commonizes the approach so it can be used for sli3 and sli4
adapters, but mandates the admin, via module parameter, specifically
identify which adapters the resets are to be removed for. Additionally,
bus_reset, which sends Target Reset TMFs to all targets, is also removed
from the template as it too has the same effect as the adapter reset.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NLaurence Oberman <loberman@redhat.com>
Tested-by: NLaurence Oberman <loberman@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update copyrights to 2017 for all files touched in this patch set
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

NVME Initiator: Merge into FC discovery

Adds NVME PRLI support and Nameserver registrations and Queries for NVME
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

NVME Initiator: Base modifications

This patch adds base modifications for NVME initiator support.

The base modifications consist of:
- Formal split of SLI3 rings from SLI-4 WQs (sometimes referred to as
  rings as well) as implementation now widely varies between the two.
- Addition of configuration modes:
   SCSI initiator only; NVME initiator only; NVME target only; and
   SCSI and NVME initiator.
   The configuration mode drives overall adapter configuration,
   offloads enabled, and resource splits.
   NVME support is only available on SLI-4 devices and newer fw.
- Implements the following based on configuration mode:
  - Exchange resources are split by protocol; Obviously, if only
     1 mode, then no split occurs. Default is 50/50. module attribute
     allows tuning.
  - Pools and config parameters are separated per-protocol
  - Each protocol has it's own set of queues, but share interrupt
    vectors.
     SCSI:
       SLI3 devices have few queues and the original style of queue
         allocation remains.
       SLI4 devices piggy back on an "io-channel" concept that
         eventually needs to merge with scsi-mq/blk-mq support (it is
	 underway).  For now, the paradigm continues as it existed
	 prior. io channel allocates N msix and N WQs (N=4 default)
	 and either round robins or uses cpu # modulo N for scheduling.
	 A bunch of module parameters allow the configuration to be
	 tuned.
     NVME (initiator):
       Allocates an msix per cpu (or whatever pci_alloc_irq_vectors
         gets)
       Allocates a WQ per cpu, and maps the WQs to msix on a WQ #
         modulo msix vector count basis.
       Module parameters exist to cap/control the config if desired.
  - Each protocol has its own buffer and dma pools.

I apologize for the size of the patch.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>

----
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This contains code cleanups that were in the prior patch set.
This allows better review of real changes later.

minor code cleanups:
 fix indentation, punctuation, line length
 addition/reduction of whitespace
 remove unneeded parens, braces
 lpfc_debugfs_nodelist_data: print as u64 rather than byte by byte
 covert printk(KERN_ERR to pr_err
 small print string deltas
 use num_present_cpus() rather than count them
 comment updates
 rctl/type names moved to module variable, not on stack
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Instead define the timeout behavior purely based on the host_template
eh_timed_out method and wire up the existing transport implementations
in the host templates.  This also clears up the confusion that the
transport template method overrides the host template one, so some
drivers have to re-override the transport template one.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix Xlane dynamic LUN set for LUN priority. Dynamic changing of the
priority was not getting reflected on the LUN.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In lpfc_new_scsi_buf_s3() and lpfc_new_scsi_buf_s4() pci_pool_alloc
followed by memset will be replaced by pci_pool_zalloc()
Signed-off-by: NSouptick joarder <jrdr.linux@gmail.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Correct panics with eh_timeout and eh_deadline

We were having double completions on our SLI-3 version of adapters.
Solved by clearing our command pointer before calling scsi_done.

The eh paths potentially ran simulatenously and would see the non-null
value and invoke scsi_done again.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fix sg_reset on SCSI device causing kernel crash

Driver could reference stale node pointers in task mgmt call.
Changed to use resetting cmd and look up node pointer in task mgmt
function.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch does a cleanup and fixes few small typos in lpfc_scsi.c
Signed-off-by: NMilan P. Gandhi <mgandhi@redhat.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The lpfc_sli4_scmd_to_wqidx_distr() function expects the scsi_cmnd
'lpfc_cmd->pCmd' not to be null, and point to the midlayer command.

That's not true in the .eh_(device|target|bus)_reset_handler path,
because lpfc_send_taskmgmt() sends commands not from the midlayer, so
does not set 'lpfc_cmd->pCmd'.

That is true in the .queuecommand path because lpfc_queuecommand()
stores the scsi_cmnd from midlayer in lpfc_cmd->pCmd; and lpfc_cmd is
stored by lpfc_scsi_prep_cmnd() in piocbq->context1 -- which is passed
to lpfc_sli4_scmd_to_wqidx_distr() as lpfc_cmd parameter.

This problem can be hit on SCSI EH, and immediately with sg_reset.
These 2 test-cases demonstrate the problem/fix with next-20160601.

Test-case 1) sg_reset

    # strace sg_reset --device /dev/sdm
    <...>
    open("/dev/sdm", O_RDWR|O_NONBLOCK)     = 3
    ioctl(3, SG_SCSI_RESET, 0x3fffde6d0994 <unfinished ...>
    +++ killed by SIGSEGV +++
    Segmentation fault

    # dmesg
    Unable to handle kernel paging request for data at address 0x00000000
    Faulting instruction address: 0xd00000001c88442c
    Oops: Kernel access of bad area, sig: 11 [#1]
    <...>
    CPU: 104 PID: 16333 Comm: sg_reset Tainted: G        W       4.7.0-rc1-next-20160601-00004-g95b89dc #6
    <...>
    NIP [d00000001c88442c] lpfc_sli4_scmd_to_wqidx_distr+0xc/0xd0 [lpfc]
    LR [d00000001c826fe8] lpfc_sli_calc_ring.part.27+0x98/0xd0 [lpfc]
    Call Trace:
    [c000003c9ec876f0] [c000003c9ec87770] 0xc000003c9ec87770 (unreliable)
    [c000003c9ec87720] [d00000001c82e004] lpfc_sli_issue_iocb+0xd4/0x260 [lpfc]
    [c000003c9ec87780] [d00000001c831a3c] lpfc_sli_issue_iocb_wait+0x15c/0x5b0 [lpfc]
    [c000003c9ec87880] [d00000001c87f27c] lpfc_send_taskmgmt+0x24c/0x650 [lpfc]
    [c000003c9ec87950] [d00000001c87fd7c] lpfc_device_reset_handler+0x10c/0x200 [lpfc]
    [c000003c9ec87a10] [c000000000610694] scsi_try_bus_device_reset+0x44/0xc0
    [c000003c9ec87a40] [c0000000006113e8] scsi_ioctl_reset+0x198/0x2c0
    [c000003c9ec87bf0] [c00000000060fe5c] scsi_ioctl+0x13c/0x4b0
    [c000003c9ec87c80] [c0000000006629b0] sd_ioctl+0xf0/0x120
    [c000003c9ec87cd0] [c00000000046e4f8] blkdev_ioctl+0x248/0xb70
    [c000003c9ec87d30] [c0000000002a1f60] block_ioctl+0x70/0x90
    [c000003c9ec87d50] [c00000000026d334] do_vfs_ioctl+0xc4/0x890
    [c000003c9ec87de0] [c00000000026db60] SyS_ioctl+0x60/0xc0
    [c000003c9ec87e30] [c000000000009120] system_call+0x38/0x108
    Instruction dump:
    <...>

    With fix:

    # strace sg_reset --device /dev/sdm
    <...>
    open("/dev/sdm", O_RDWR|O_NONBLOCK)     = 3
    ioctl(3, SG_SCSI_RESET, 0x3fffe103c554) = 0
    close(3)                                = 0
    exit_group(0)                           = ?
    +++ exited with 0 +++

    # dmesg
    [  424.658649] lpfc 0006:01:00.4: 4:(0):0713 SCSI layer issued Device Reset (1, 0) return x2002

Test-case 2) SCSI EH

    Using this debug patch to wire an SCSI EH trigger, for lpfc_scsi_cmd_iocb_cmpl():
    -       cmd->scsi_done(cmd);
    +       if ((phba->pport ? phba->pport->cfg_log_verbose : phba->cfg_log_verbose) == 0x32100000)
    +               printk(KERN_ALERT "lpfc: skip scsi_done()\n");
    +       else
    +               cmd->scsi_done(cmd);

    # echo 0x32100000 > /sys/class/scsi_host/host11/lpfc_log_verbose

    # dd if=/dev/sdm of=/dev/null iflag=direct &
    <...>

    After a while:

    # dmesg
    lpfc 0006:01:00.4: 4:(0):3053 lpfc_log_verbose changed from 0 (x0) to 839909376 (x32100000)
    lpfc: skip scsi_done()
    <...>
    Unable to handle kernel paging request for data at address 0x00000000
    Faulting instruction address: 0xd0000000199e448c
    Oops: Kernel access of bad area, sig: 11 [#1]
    <...>
    CPU: 96 PID: 28556 Comm: scsi_eh_11 Tainted: G        W       4.7.0-rc1-next-20160601-00004-g95b89dc #6
    <...>
    NIP [d0000000199e448c] lpfc_sli4_scmd_to_wqidx_distr+0xc/0xd0 [lpfc]
    LR [d000000019986fe8] lpfc_sli_calc_ring.part.27+0x98/0xd0 [lpfc]
    Call Trace:
    [c000000ff0d0b890] [c000000ff0d0b900] 0xc000000ff0d0b900 (unreliable)
    [c000000ff0d0b8c0] [d00000001998e004] lpfc_sli_issue_iocb+0xd4/0x260 [lpfc]
    [c000000ff0d0b920] [d000000019991a3c] lpfc_sli_issue_iocb_wait+0x15c/0x5b0 [lpfc]
    [c000000ff0d0ba20] [d0000000199df27c] lpfc_send_taskmgmt+0x24c/0x650 [lpfc]
    [c000000ff0d0baf0] [d0000000199dfd7c] lpfc_device_reset_handler+0x10c/0x200 [lpfc]
    [c000000ff0d0bbb0] [c000000000610694] scsi_try_bus_device_reset+0x44/0xc0
    [c000000ff0d0bbe0] [c0000000006126cc] scsi_eh_ready_devs+0x49c/0x9c0
    [c000000ff0d0bcb0] [c000000000614160] scsi_error_handler+0x580/0x680
    [c000000ff0d0bd80] [c0000000000ae848] kthread+0x108/0x130
    [c000000ff0d0be30] [c0000000000094a8] ret_from_kernel_thread+0x5c/0xb4
    Instruction dump:
    <...>

    With fix:

    # dmesg
    lpfc 0006:01:00.4: 4:(0):3053 lpfc_log_verbose changed from 0 (x0) to 839909376 (x32100000)
    lpfc: skip scsi_done()
    <...>
    lpfc 0006:01:00.4: 4:(0):0713 SCSI layer issued Device Reset (0, 0) return x2002
    <...>
    lpfc 0006:01:00.4: 4:(0):0723 SCSI layer issued Target Reset (1, 0) return x2002
    <...>
    lpfc 0006:01:00.4: 4:(0):0714 SCSI layer issued Bus Reset Data: x2002
    <...>
    lpfc 0006:01:00.4: 4:(0):3172 SCSI layer issued Host Reset Data:
    <...>

Fixes: 8b0dff14 ("lpfc: Add support for using block multi-queue")
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: NMauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Copyright updates
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add support for XLane LUN priority
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add sysfs proc_name support
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This removes a redundant code block that will either be executed if the
ENABLE_FCP_RING_POLLING flag is set in phba->cfg_poll or not. The code
is just duplicated in both cases, hence we unify it again.

This probably is a left over from some sort of refactoring.
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NSebastian Herbszt <herbszt@gmx.de>
Acked-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use new FDMI speed definitions for 10G, 25G and 40G FCoE.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Make write check error processing more resilient.

Checks to catch writes that fw reports weren't fully complete yet SCSI
status indicated fine needed correction.
Signed-off-by: NDick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: NJames Smart <james.smart@avagotech.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>