- 27 6月, 2006 6 次提交
-
-
由 NeilBrown 提交于
It appears in /sys/mdX/md/dev-YYY/state and can be set or cleared by writing 'writemostly' or '-writemostly' respectively. Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
The md/dev-XXX/state file can now be written: "faulty" simulates an error on the device "remove" removes the device from the array (if it is not busy) Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
This allows the state of an md/array to be directly controlled via sysfs and adds the ability to stop and array without tearing it down. Array states/settings: clear No devices, no size, no level Equivalent to STOP_ARRAY ioctl inactive May have some settings, but array is not active all IO results in error When written, doesn't tear down array, but just stops it suspended (not supported yet) All IO requests will block. The array can be reconfigured. Writing this, if accepted, will block until array is quiescent readonly no resync can happen. no superblocks get written. write requests fail read-auto like readonly, but behaves like 'clean' on a write request. clean - no pending writes, but otherwise active. When written to inactive array, starts without resync If a write request arrives then if metadata is known, mark 'dirty' and switch to 'active'. if not known, block and switch to write-pending If written to an active array that has pending writes, then fails. active fully active: IO and resync can be happening. When written to inactive array, starts with resync write-pending (not supported yet) clean, but writes are blocked waiting for 'active' to be written. active-idle like active, but no writes have been seen for a while (100msec). Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
When a md array has been idle (no writes) for 20msecs it is marked as 'clean'. This delay turns out to be too short for some real workloads. So increase it to 200msec (the time to update the metadata should be a tiny fraction of that) and make it sysfs-configurable. Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 07 1月, 2006 12 次提交
-
-
由 NeilBrown 提交于
Also export current (average) speed and status in sysfs. Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Writing major:minor to md/new_dev will bind that device to the array. Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
This the role that a device has in an array can be viewed and set. Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
If array is active, try to reshape, else just set the value. Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Store this total in superblock (As appropriate), and make it available to userspace via sysfs. Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Allow it to be set to a particular version, or 'none'. Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
... only before array is started of course. Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg KH <greg@kroah.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 NeilBrown 提交于
See patch to md.txt for more details Signed-off-by: NNeil Brown <neilb@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 09 11月, 2005 1 次提交
-
-
由 NeilBrown 提交于
Document in Documentation/md.txt the files that now appear in sysfs, and make a couple of small refinements to exactly when 'level' and 'raid_disks' are empty, to make it match the documentation. Signed-off-by: NNeil Brown <neilb@suse.de> Acked-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 17 4月, 2005 1 次提交
-
-
由 Linus Torvalds 提交于
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
-