If we have clients stalled waiting for requests, ignore the GPU if it
signals that it should downclock due to low load. This helps prevent
the automatic timeout from causing extremely long running batches from
taking even longer.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that we have internal clients, rather than faking a whole
drm_i915_file_private just for tracking RPS boosts, create a new struct
intel_rps_client and pass it along when waiting.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since we will often pageflip to an active surface, we will often have to
wait for the surface to be written before issuing the flip. Also we are
likely to wait on that surface in plenty of time before the vblank.
Since we have a mechanism for boosting when a flip misses the expected
vblank, curtain the number of times we RPS boost when simply waiting for
mmioflip.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Ring switches can occur many times per frame, and are often out of
control, causing frequent RPS boosting for no practical benefit. Treat
the sw semaphore synchronisation as a separate client and only allow it
to boost once per busy/idle cycle.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This trims a little overhead from the common case of not needing to
synchronize between rings.

v2: execlists is special and likes to duplicate code.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently, we only track the last request globally across all engines.
This prevents us from issuing concurrent read requests on e.g. the RCS
and BCS engines (or more likely the render and media engines). Without
semaphores, we incur costly stalls as we synchronise between rings -
greatly impacting the current performance of Broadwell versus Haswell in
certain workloads (like video decode). With the introduction of
reference counted requests, it is much easier to track the last request
per ring, as well as the last global write request so that we can
optimise inter-engine read read requests (as well as better optimise
certain CPU waits).

v2: Fix inverted readonly condition for nonblocking waits.
v3: Handle non-continguous engine array after waits
v4: Rebase, tidy, rewrite ring list debugging
v5: Use obj->active as a bitfield, it looks cool
v6: Micro-optimise, mostly involving moving code around
v7: Fix retire-requests-upto for execlists (and multiple rq->ringbuf)
v8: Rebase
v9: Refactor i915_gem_object_sync() to allow the compiler to better
optimise it.

Benchmark: igt/gem_read_read_speed
hsw:gt3e (with semaphores):
Before: Time to read-read 1024k:		275.794µs
After:  Time to read-read 1024k:		123.260µs

hsw:gt3e (w/o semaphores):
Before: Time to read-read 1024k:		230.433µs
After:  Time to read-read 1024k:		124.593µs

bdw-u (w/o semaphores):             Before          After
Time to read-read 1x1:            26.274µs       10.350µs
Time to read-read 128x128:        40.097µs       21.366µs
Time to read-read 256x256:        77.087µs       42.608µs
Time to read-read 512x512:       281.999µs      181.155µs
Time to read-read 1024x1024:    1196.141µs     1118.223µs
Time to read-read 2048x2048:    5639.072µs     5225.837µs
Time to read-read 4096x4096:   22401.662µs    21137.067µs
Time to read-read 8192x8192:   89617.735µs    85637.681µs

Testcase: igt/gem_concurrent_blit (read-read and friends)
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> [v8]
[danvet: s/\<rq\>/req/g]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The merged seqno->request conversion from John called request
variables req, but some (not all) of Chris' recent patches changed
those to just rq. We've had a lenghty (and inconclusive) discussion on
irc which is the more meaningful name with maybe at most a slight bias
towards req.

Given that the "don't change names without good reason to avoid
conflicts" rule applies, so lets go back to a req everywhere for
consistency. I'll sed any patches for which this will cause conflicts
before applying.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
[danvet: s/origina/merged/ as pointed out by Chris - the first
mass-conversion patch was from Chris, the merged one from John.]
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

v2:
- set the override disable flag too on stepping F0 (mika)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On B0 and C0 steppings the workaround enable bit would be overriden by
default, so the overriding must be disabled.

The WA was added in
commit 83a24979
Author: Nick Hoath <nicholas.hoath@intel.com>
Date:   Fri Apr 10 13:12:26 2015 +0100

    drm/i915/bxt: Add WaForceContextSaveRestoreNonCoherent
Spotted-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Our driver compiles clean (nowadays thanks to 0day) but for me, at least,
it would be beneficial if the compiler threw an error rather than a
warning when it found a piece of suspect code. (I use this to
compile-check patch series and want to break on the first compiler error
in order to fix the patch.)

v2: Kick off a new "Debugging" submenu for i915.ko
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJani Nikula <jani.nikula@intel.com>
[danvet: Add "DRM i915" to the menu name as requested by Chris.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The macros we use there are the magic ones that can take either dev or
dev_priv. We'd like to move as much as possible towards dev_priv though.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Couldn't let it go!
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently bxt_resume_prepare() is only used in the runtime-resume path.
Add it to the full S3/S4 path as well.

v2: Rebase on top of the vlv_resume_prepare() shuffling around

Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since DRM_ROTATE is counter clockwise (which is compliant with Xrandr),
and HW rotation is clockwise, swapping 90/270 to work as expected from
userspace.

v2: Rebased
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Explain why a few fields of the new pipe_config have their values
preserved, while the others are zeroed.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Also make the WA comment consistent with the rest, where the stepping
info is not shown.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

ARGB8888 is used for cursors on all platforms so we need to allow it
everywhere.

ABGR8888 is currently only honoured:
  - on VLV/CHV in sprite planes
  - on SKL+ for primary and sprite planes
so only allow it for those platforms.

Note that we only support ARGB8888/ABGR8888 on the primary plane for
SKL/BXT because we have in line of sight the pipe bottom color on those
platforms and because the primary plane programming on VLV/CHV doesn't
anything different for those formats today.

v2: Fix the logic to forbid the creation ABGR2101010 fbs (Ville)
v3: Still allow the creation of ARGB8888 fbs now that cursor planes use
    real fb objects (found by PRTS).
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Making lane stagger calculation common for HDMI and DP

v2: Imre's comments addressed
	- Remove lane stagger from bxt_clk_div and make it a local variable in
	ddi_pll_select
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

BUN 1: prop_coeff, int_coeff, tdctargetcnt programming updated and tied to
VCO frequencies. Program i_lockthresh in PORT_PLL_9.

VCO calculated based on the formula:
Desired Output = Port bit rate in MHz (DisplayPort HBR2 is 5400 MHz)
Fast Clock = Desired Output / 2
VCO = Fast Clock * P1 * P2

Prop_coeff, int_coeff, and tdctargetcnt modified according to above
calculation.

BUN 2: Port PLLs require additional programming at certain frequencies -
DCO amplitude in PORT_PLL_10

Review comments from Siva which were addressed in the initial version of the
patch.
	- Change PORT_PLL_LOCK_THRESHOLD to PORT_PLL_LOCK_THRESHOLD_MASK
	- Calculate for HDMI
	- Correct values for vco = 5.4
	- return in case of invalid vco range

v2: Imre's review comments addressed
	- change dcoampovr_en to dcoampovr_en_h
	- change PORT_PLL_DCO_AMP_OVR_EN to PORT_PLL_DCO_AMP_OVR_EN_H
	- Correct lane stagger value for 324MHz
	- Make coef common for HDMI and DP
	- remove superfluous comments

v3: Imre's comments addressed
	- Remove Prop_coeff, int_coeff, tdctargetcnt, dcoampovr_en, gain_ctl,
	dcoampovr_en_h from bxt_clk_div and make them local variables.
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> [v1]
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Be in line with other features that we have.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Turn

    [drm:intel_dp_print_rates] source rates: 162000,270000,540000,
    [drm:intel_dp_print_rates] sink rates: 162000,270000,
    [drm:intel_dp_print_rates] common rates: 162000,270000,

into

    [drm:intel_dp_print_rates] source rates: 162000, 270000, 540000
    [drm:intel_dp_print_rates] sink rates: 162000, 270000
    [drm:intel_dp_print_rates] common rates: 162000, 270000
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We just have have VLV and CHV sprites programming the hardware
differently for the ABGR2101010 so keep them working.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

That define makes it hard to figure out what is the actual list of
formats at a glance. Expand it then.
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Mika encountered one pathological scenario under X where acquiring all
the mm locks (required to insert a mmu notifier) was very slow, so slow
that by the time we tried to lock the struct_mutex with the usual call
to i915_mutex_lock_interruptible(), X's signal timer had fired causing
us to restart the ioctl (and so looped indefinitely).

While I suspect this is the result of another bug (something leaking mm
perhaps?) we can forgo the error checking and interuptible nature of the
lock here so we only have to pay the expense once and get on with it.
This does expose the userptr creation routine to a driver livelock
though by not being interruptible.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Init ret to avoid issues reported by PRTS.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When the modeset code is reached with a CRTC that only needs a flip, the
code that assigns PLLs is skipped. But since there is still a state swap
for that CRTC, the current PLL assignment needs to be preserved. I
missed the ddi_pll_sel field in the following commit, which causes
warnings in DDI platforms.

commit 4978cc93
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date:   Tue Apr 21 17:13:21 2015 +0300

    drm/i915: Preserve shared DPLL information in new pipe_config

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90410Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Split strings to 80 char, add ddi_pll_sel and fixed typo. (Damien Lespiau)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the following commit, the place where the contents of dpll_hw_state
in crtc_state where zeroed was changed. Prior to that commit, it
happened when the new state was allocated, but now that happens just
before the call the .crtc_compute_clock() hook. The DP code for SKL,
however, sets up the (private) PLL in the encoder compute config
function that has already run by the time that memset() is reached,
causing the previous value to be lost.

This patch fixes the issue by moving the memset() down the call chain,
so that it is only called if the values in dpll_hw_state are going to be
updated.

commit 4978cc93
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date:   Tue Apr 21 17:13:21 2015 +0300

    drm/i915: Preserve shared DPLL information in new pipe_config

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90462Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Reported-and-tested-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add one explicit discard of __iomem address space qualifier in
validate_vbt(), and respect it otherwise. This adds clarity in the code,
and reduces the sparse warnings from the module to just one.

Quoting Daniel, "The vbt really is plain old memory. Except that it's
reserved in the e820 table as something special and hence treated as io
range by the kernel. But it is memory, hence casting away the __iomem is
imo the right approach."
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just so it is grouped logically in line with other data and makes a
rather verbose output a bit shorter.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NChandra Konduru <chandra.konduru@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Improve clarity. No functional changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We never pass a non-NULL vbt to validate_vbt, and we can safely expect
the callers to not change.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Ville noticed in another patch we we didn't need them at all, so remove
them. It's worth saying that it makes no difference to code generated as
gcc is clever enough to optimize it out.

v2: Remove 'break' after 'return' in switches (Ville)
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently DSI PLL N1 is hardcoded off. Make it possible to use it
later. This should have no functional changes for now.

v2: s/ffz(~(n))/ffs(n) - 1/ (Ville)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Added docbook info regarding context save and restore (CSR)
firmware support added from gen9 onwards to drive newly added
DMC (Display microcontroller) in display engine.

v1: Initial version as RFC.

v2: Used "DOC:" tag for csr description based on review comment from Daniel.
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reading from disconnected ports will spit out timeout error
on the dmesg. Skip the attempted read if the port is not
connected and avoid confusing users/testcases about
expected timeouts.

This new dpcd debugfs entry was introduced by commit aa7471d2
("drm/i915: add i915 specific connector debugfs file for DPCD")

v2 by Jani: move the check at the top, out of the loop.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90060
Tested-by: yex.tian@intel.com
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is an extra semi-colon on the if statement so the debug output
always says "Failed to write EDID checksum" even when it didn't fail.

Fixes: 559be30c ('drm/i915: Implement the intel_dp_autotest_edid function for DP EDID complaince tests')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>