The hardware incorrectly process L0S/L1 entrance if the chipset/root
response after specific/shorter timer and cause system hang.
Enlarge the timeout value to avoid this issue.
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Tested-by: NLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some platform with EEPROM/OTP existing, the BIOS could overwrite
a new MAC address for the NIC. so, the permanent mac address should
be from BIOS. the address is restored when driver removing.
Voltage raising isn't applicable for l1d.
Replace swab32 with htonl for big/little endian platform.
related Registers are refined as well.
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Tested-by: NLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Close-action is done by atl1c_reset_pcie, remove it from
atl1c_get_permanent_address.
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Tested-by: NLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WoL status is read-clear and should be cleared when in S0
status.
putting it in atl1c_reset_pcie is more suitable than
in atl1c_get_permanent_address.
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Tested-by: NLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some platforms the PHY settings need to change depending on the
cable link status to get better stability.
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Tested-by: NLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All supported devices have one issue that msi interrupt doesn't assert
if pci command register bit (PCI_COMMAND_INTX_DISABLE) is set.
Add workaround in drivers/pci/quirks.c
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before doing skb->head_frag work on bnx2x driver, I found too much stuff
was inlined in bnx2x/bnx2x_cmn.h for no good reason and made my work not
very easy.

Move some big functions out of this include file to the respective .c
file.

A lot of inline keywords are not needed at all in this huge driver.

   text	   data	    bss	    dec	    hex	filename
 490083	   1270	     56	 491409	  77f91	bnx2x/bnx2x.ko.before
 484206	   1270	     56	 485532	  7689c	bnx2x/bnx2x.ko
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reset logic after a Rx FIFO overrun will clear the programmed
multicast addresses. This patch fixes the issue by reprogramming the
registers after the reset.

The commit eefc48b0 ("pch_gbe: reprogram multicast address register on
reset") tried to fix this problem, but it introduces unnecessary
codes. In fact, all multicast addresses have been saved in netdev->mc,
So we can call pch_gbe_set_multi() directly after reset_hw and
reset_rx.

This commit kills 50+ line codes

Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: NRongQing.Li <roy.qing.li@gmail.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts tg3 driver, one of our reference drivers, to use new
build_skb() api in frag mode.

Instead of using kmalloc() to allocate the memory block that will be
used by build_skb() as skb->head, we use a page fragment.

This is a followup of patch "net: allow skb->head to be a page fragment"

This allows GRO, TCP coalescing, and splice() to be more efficient.

Incidentally, this also removes SLUB slow path contention in kfree()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->head is currently allocated from kmalloc(). This is convenient but
has the drawback the data cannot be converted to a page fragment if
needed.

We have three spots were it hurts :

1) GRO aggregation

 When a linear skb must be appended to another skb, GRO uses the
frag_list fallback, very inefficient since we keep all struct sk_buff
around. So drivers enabling GRO but delivering linear skbs to network
stack aren't enabling full GRO power.

2) splice(socket -> pipe).

 We must copy the linear part to a page fragment.
 This kind of defeats splice() purpose (zero copy claim)

3) TCP coalescing.

 Recently introduced, this permits to group several contiguous segments
into a single skb. This shortens queue lengths and save kernel memory,
and greatly reduce probabilities of TCP collapses. This coalescing
doesnt work on linear skbs (or we would need to copy data, this would be
too slow)

Given all these issues, the following patch introduces the possibility
of having skb->head be a fragment in itself. We use a new skb flag,
skb->head_frag to carry this information.

build_skb() is changed to accept a frag_size argument. Drivers willing
to provide a page fragment instead of kmalloc() data will set a non zero
value, set to the fragment size.

Then, on situations we need to convert the skb head to a frag in itself,
we can check if skb->head_frag is set and avoid the copies or various
fallbacks we have.

This means drivers currently using frags could be updated to avoid the
current skb->head allocation and reduce their memory footprint (aka skb
truesize). (thats 512 or 1024 bytes saved per skb). This also makes
bpf/netfilter faster since the 'first frag' will be part of skb linear
part, no need to copy data.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Insert an skb_tx_timestamp call in both ndo_start_xmit routines
Tested to work for the nv_start_xmit_optimized case
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If I understand correct, NETIF_F_IP_CSUM only means the hardware
will compute the TCP/UDP checksum, IP checksum is always computed
in software

So as a workround of hardware unable to compute small packages
checksum, do not need to compute IP header checksum.
Signed-off-by: NRongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCH_GBE_ETH_ALEN is equal to ETH_ALEN, so we can replace it with
ETH_ALEN.

If they are not equal, it must be a bug, since this is ethernet,
and the address has been already stored to mc_addr_list as ETH_ALEN
bytes when call pch_gbe_mac_mc_addr_list_update.
Signed-off-by: NRongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the gpio_to_irq() function to retrieve the phy IRQ line
from the GPIO pin specification.
This fix is needed now that we have moved to irqdomains on AT91.
Reported-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AT91RM9200 Ethernet controller still has a fixed IO mapping.
So:
* Remove the fixed IO mapping and AT91_VA_BASE_EMAC definition.
* Pass the physical base-address via platform-resources to the driver.
* Convert at91_ether.c driver to perform an ioremap().
* Ethernet PHY detection needs to be performed during the driver
initialization process, it can no longer be done first.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch consolidates the case logic for checking whether a device supports
WoL into a single place. Previously ethtool and probe used similar logic that
was copied and maintained separately. This patch encapsulates the core logic
into a function so that a user only has to update one place.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During igb_reset(), we initiate a hardware reset which will clear our
flow control settings. For auto-negotiation, we re-negotiate them when
linking up again, but we need to force them off properly for the forced
speed case.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously, a workaround was added to address a hardware bug in the
PCIm2PCI arbiter where a write by the driver of the Transmit/Receive
Descriptor Tail register could happen concurrently with a write of any
MAC CSR register by the Manageability Engine (ME) which could cause the
Tail register to have an incorrect value.  The arbiter is supposed to
prevent the concurrent writes but there is a bug that can cause the Host
(driver) access to be acknowledged later than it should.
After further investigation, it was discovered that a driver write access
of any MAC CSR register after being idle for some time can be lost when
ME is accessing a MAC CSR register.  When this happens, no further target
access is claimed by the MAC which could hang the system.
The workaround to check bit 24 in the FWSM register (set only when ME is
accessing a MAC CSR register) and delay for a limited amount of time until
it is cleared is now done for all driver writes of MAC CSR registers on
82579 with ME enabled.  In the rare case when the driver is writing the
Tail register and ME is accessing any MAC CSR register for a duration
longer than the maximum delay, write the register and verify it has the
correct value before continuing, otherwise reset the device.

This patch also moves some pre-existing macros from the hardware-specific
header file to the more appropriate generic driver header file.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In K1 mode (a MAC/PHY interconnect power mode), the 82579 device shuts down
the Phase Lock Loop (PLL) of the interconnect to save power.  When the PLL
starts working, the 82579 device may start to transfer the packet through
the interconnect before it is fully functional causing packet drops.  This
workaround disables shutting down the PLL in K1 mode for 1G link speed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Performance testing has shown that enabling DMA burst on 82574
improves performance on small packets, so enable it by default.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

80003ES2LAN has an errata such that far-end loopback may be activated by
bit errors producing a reserved symbol. In order to disable far-end
loopback quickly enough, disable it immediately following a reset.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

logical speed returned by link_status_query needs to be multiplied by 10.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This has been used by me and others for ages, let's stop calling it
experimental.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As none of the callers of bond_update_speed_duplex (need to) check its
return value, there is little point in it returning anything.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o 0x3, 0x7, 0xF, 0x1F, 0x3F, 0x7F and 0xFF are the allowed capture masks.
o Updated driver version to 5.0.28
Signed-off-by: NManish chopra <manish.chopra@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Without failing probe, register netdevice when device is in FAILED state.
o Device will come up with minimum functionality.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the custom DIVA_{INIT,EXIT}_FUNCTION defines and use
the standard __init,__exit markup.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Armin Schindler <mac@melware.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fragmentation is usefull if multiple devices are connected to an E1
interface. Each fragment will have a subset of the available timeslots.
These devices require a cascde connection or a multiplexer.
Signed-off-by: NAndreas Eversberg <jolly@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LEDs will show RED if layer 1 is disabled or fails.
LEDs will show GREEN if layer 1 is active.
LEDs will blink if traffic on D-channel.
Signed-off-by: NAndreas Eversberg <jolly@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already have the flag for L1 active, so we should use it.
L2 will be solved in a later patch.
Signed-off-by: NAndreas Eversberg <andreas@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Transmitted audio data was interrupted if a bridge was enabled or disabled.
Now transmission seamlessly continues during that action.
Fix in hfcmulti.ko
Signed-off-by: NAndreas Eversberg <jolly@eversberg.eu>
Signed-off-by: NKarsten Keil <keil@b1-systems.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

merge TXQ/RXQ/MAC start/enable code to one function as they
are started/enabled at the same time, just like stop/disable them
in the function of atl1c_stop_mac.
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Tested-by: NLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is used for suspend of S1/S3/S4 and driver remove.
It sets MAC/PHY based on the WoL configuation to get lower power
consumption.
atl1c_phy_power_saving is renamed to atl1c_phy_to_ps_link, this
function is just make PHY enter a link/speed mode to eat less
power.
REG_MAC_CTRL register is refined as well.
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Tested-by: NLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

it's unnecessary to reset/init phy when link down.
Only L1/L2 chip (supported by atlx) need such action.
Signed-off-by: Nxiong <xiong@qca.qualcomm.com>
Tested-by: NLiu David <dwliu@qca.qualcomm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>