If don't reorder initialization like this, we will never be able to
get a reference to ULPI PHYs.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.

When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).

On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NGuenter Roeck <groeck@chromium.org>
Signed-off-by: NWilliam Wu <william.wu@rock-chips.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

If dr_mode is "otg" then support dual role mode of operation.
Currently this mode is only supported when an extcon handle is
present in the dwc3 device tree node. This is needed to
get the ID status events of the port.

We're using a workqueue to manage the dual-role state transitions
as the extcon notifier (dwc3_drd_notifier) is called in an atomic
context by extcon_sync() and this doesn't go well with
usb_del_gadget_udc() causing a lockdep and softirq warning.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

We can't have both Host and Peripheral roles active at the same time
because of one detail on DWC3: it shares the same memory area for both
Host and Peripheral registers.

When swapping roles we must reinitialize the new role every
time. Let's make sure this works for our debugfs interface.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

We're going to use this member to track which role we're currently
playing, that way we can more easily implement dual-role swap in
upcoming patches.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

- DWC_USB3_NUM indicates the number of Device mode single directional
  endpoints, including OUT and IN endpoint 0.

- DWC_USB3_NUM_IN_EPS indicates the maximum number of Device mode IN
  endpoints active at any time, including control endpoint 0.

It's possible to configure RTL such that DWC_USB3_NUM_EPS is equal to
DWC_USB3_NUM_IN_EPS.

dwc3-core calculates the number of OUT endpoints as DWC_USB3_NUM minus
DWC_USB3_NUM_IN_EPS. If RTL has been configured with DWC_USB3_NUM_IN_EPS
equal to DWC_USB3_NUM then dwc3-core will calculate the number of OUT
endpoints as zero.

For example a from dwc3_core_num_eps() shows:
[    1.565000]  /usb0@f01d0000: found 8 IN and 0 OUT endpoints

This patch refactors the endpoint calculation down to one variable
dwc->num_eps taking care to maintain the current mapping of endpoints for
fixed FPGA configurations as described in Table 4-7 of version 2.60a of the
DWC USB3 databook.

The endpoint mapping will then be EP-OUT, EP-IN etc, up to DWC_USB3_NUM.
If DWC_USB3_NUM is odd then OUT will take the extra endpoint.
Suggested-by: NFelipe Balbi <balbi@kernel.org>
Signed-off-by: NBryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This bit is only supposed to be used with known
buggy PHYs, however some platforms might erroneously
set it. In order to avoid it, let's make sure this
bit is always cleared. If some PHY needs this, we
will need to add a quirk flag.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The dma ops for dwc3 devices are not set properly. So, use a
physical device sysdev, which will be inherited from parent,
to set the hardware / firmware parameters like dma.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NSriram Dash <sriram.dash@nxp.com>
Tested-by: NBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This is a workaround for STAR 9000961433 which affects only version
3.00a of the DWC_usb3 core. This prevents the controller interrupt from
being masked while handling events. Enabling interrupt moderation allows
us to work around this issue because once the GEVNTCOUNT.count is
written the IRQ is immediately deasserted and won't be asserted again
until GEVNTCOUNT.EHB is cleared.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Implement interrupt moderation which allows the interrupt rate to be
throttled. To enable this feature the dwc->imod_interval must be set to
1 or greater. This value specifies the minimum inter-interrupt interval,
in 250 ns increments. A value of 0 disables interrupt moderation.

This applies for DWC_usb3 version 3.00a and higher and for DWC_usb31
version 1.20a and higher.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This extra buffer will be used so we can copy
triggered events from our event buffer to this cache
and process all of them later in bottom half
handler.

We need this in order to implement a workaround for
a known erratum in recent DWC3 release.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

dwc3_soft_reset() is doing the same thing as
dwc3_core_soft_reset(). Let's remove
dwc3_soft_reset() since that's not needed anymore.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add a function to check properties and call it from probe. This will
allow us to add check code without bloating the probe function. This
needs to be done after dwc3_get_properties() and dwc3_core_init() so
that all the properties and hardware configs are available.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Finally get rid of dwc3_trace() hack. If any other
message is truly needed, we should add proper
tracepoints for them instead of hacking around with
dwc3_trace() or similar.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This helper will be responsible for reading and
parsing our properties. No functional changes in
this patch, cleanup only.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Kernel will give us page aligned memory anyway.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This little helper will be used to setup anything
related to GCTL register. There are no functional
changes, this is a cleanup only patch.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This little helper will be used to make sure we're
dealing with a valid Synopsys DWC3 or DWC3.1 core.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

For the usb31 IP and from version 2.90a of the usb3 IP, the core
supports HW exit from L1 in HS. Enable it, otherwise the controller may
never exit from LPM to do a transfer.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Member @mem in struct dwc3 is not used in any places. Clean up it.
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Fixing the sequence of events in dwc3_core_init() error exit path.
dwc3_core_exit() call is also removed from the error path since,
whatever it's doing is already done.

Fixes: c499ff71 usb: dwc3: core: re-factor init and exit paths

Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Stable <stable@vger.kernel.org> # 4.8+
Signed-off-by: NVivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This patch follows the similar fix in dwc2. See
commit 5268ed9d ("usb: dwc2: Fix dr_mode validation")

Currently, the dr_mode is only checked against the module configuration.
It also needs to be checked against the hardware capablities.

The driver now checks if both the module configuration and hardware are
capable of the dr_mode value. If not, then it will issue a warning and
fall back to a supported value. If it is unable to fall back to a
suitable value, then the probe will fail.

Behavior summary:

      module          :  actual
 HW   config  dr_mode :  dr_mode
---------------------------------
 host  host   any     :  host
 host  dev    any     :  INVALID
 host  otg    any     :  host

 dev   host   any     :  INVALID
 dev   dev    any     :  dev
 dev   otg    any     :  dev

 otg   host   any     :  host
 otg   dev    any     :  dev
 otg   otg    any     :  dr_mode
Signed-off-by: NThinh Nguyen <thinhn@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].

This feature is NOT available on the DWC_usb31 (USB 3.1) IP.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

When dwc3 core enters into suspend mode, the system (especially for mobile
device) may power off the dwc3 controller for power saving, that will cause
dwc3 controller lost the mode operation when resuming dwc3 core.

Thus we can move the mode setting into dwc3_core_init() function to avoid this
issue.
Signed-off-by: NBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Signed-off-by: NWilliam Wu <william.wu@rock-chips.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.

But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.
Signed-off-by: NWilliam Wu <william.wu@rock-chips.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Signed-off-by: NWilliam Wu <william.wu@rock-chips.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

After going through runtime_suspend/runtime_resume
cycle once we would be left with an unbalanced
pm_runtime_get() call. Fix that by making sure that
we try to suspend right after resuming so things are
balanced and device can runtime_suspend again.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Implementations might use different IRQs for
host, gadget so use named interrupt resources
to allow device tree to specify the interrupts.

Following are the interrupt names

Peripheral Interrupt - peripheral
HOST Interrupt - host

Maintain backward compatibility for a single named
interrupt ("dwc3_usb3") for all interrupts as well as
unnamed interrupt at index 0 for all interrupts.

As platform_get_irq() variants are used, tackle
the -EPROBE_DEFER case as well.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

If there is a failure after pm_runtime_enable/get_sync()
we need to call pm_runtime_disable/put_sync().

Otherwise it will lead to an unbalanced pm_runtime_enable() on the
subsequent probe if the earlier probe bailed out due to -EPROBE_DEFER.

pm_runtime_get_sync() can fail as well so deal with that case too.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

We shouldn't change a host-only dwc3 to gadget-only
if driver is built as gadget-only. Fix that up here.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

No more users for it.
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

this patch implements the most basic pm_runtime
support for dwc3. Whenever USB cable is dettached,
then we will allow core to runtime_suspend.

Runtime suspending will involve completely tearing
down event buffers and require a full soft-reset of
the IP.

Note that a further optimization could be
implemented once we decide to support hibernation,
which is to allow runtime_suspend with cable
connected when bus is in U3. That's subject to a
separate patch, however.
Tested-by: NBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

now that we have re-factored dwc3_core_init() and
dwc3_core_exit() we can use them for suspend/resume
operations.

This will help us avoid some common mistakes when
patching code when we have duplicated pieces of code
doing the same thing.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The idea of this patch is for dwc3_core_init() to
abstract all the details about how to initialize
dwc3 and dwc3_core_exit() to do the same for
teardown.

With this, we can simplify suspend/resume operations
by a large margin and always know that we're going
to start dwc3 from a known starting point.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

this patch is in preparation for some further
re-factoring in dwc3 initialization. No functional
changes.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

that macro is unnecessary and just adds pointless
obfuscation. Let's remove it.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

this helper will be used, initially, to dump space
of different queues and fifos in dwc3 to
debugfs. Later, it'll be used to issue remote wakeup
when we want to start a transfer and there's
something in a TX FIFO.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Debugfs init failure is not so important. We can continue our job on
this failure. Also no break need for debugfs_create_file call failure.
Signed-off-by: NDu, Changbin <changbin.du@intel.com>

[felipe.balbi@linux.intel.com :
	- remove out-of-memory message, we get that from OOM.
	- switch dev_err() to dev_dbg() ]
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: NSriram Dash <sriram.dash@nxp.com>
Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>