On HP 800 G4 DM, if HDMI cable isn't plugged before boot, the HDMI port
becomes useless and never responds to cable hotplugging:
[    3.031904] [drm:lspcon_init [i915]] *ERROR* Failed to probe lspcon
[    3.031945] [drm:intel_ddi_init [i915]] *ERROR* LSPCON init failed on port D

Seems like the lspcon chip on the system only gets powered after the
cable is plugged.

Consilidate lspcon_init() into lspcon_resume() to dynamically init
lspcon chip, and make HDMI port work.

v6:
 - Rebase on latest for-linux-next.
v5:
 - Consolidate lspcon_resume() with lspcon_init().
 - Move more logic into lspcon code.
v4:
 - Trust VBT in intel_infoframe_init().
 - Init lspcon in intel_dp_detect().
v3:
 - Make sure it's handled under long HPD case.
v2:
 - Move lspcon_init() inside of intel_dp_hpd_pulse().

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/203Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200610075542.12882-1-kai.heng.feng@canonical.com

Since DP 1.3, it's been possible for DP receivers to specify an
additional set of DPCD capabilities, which can take precedence over the
capabilities reported at DP_DPCD_REV.

Basically any device supporting DP is going to need to read these in an
identical manner, in particular nouveau, so let's go ahead and just move
this code out of i915 into a shared DRM DP helper that we can use in
other drivers.

v2:
* Remove redundant dpcd[DP_DPCD_REV] == 0 check
* Fix drm_dp_dpcd_read() ret checks
Signed-off-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NSean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-20-lyude@redhat.com

We have a mix of dport, intel_dport, intel_dig_port and dig_port to
reference a intel_digital_port struct. Numbers are around

5	intel_dport
36	dport
479	intel_dig_port
352	dig_port

Since we already removed the intel_ prefix from most of our other
structs, do the same here and prefer dig_port.

v2: rename everything in i915, not just a few display sources and
reword commit message (from Matt Roper)
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701045054.23357-1-lucas.demarchi@intel.com

Compared to implementation of DP and HDMI's encoder->infoframes_enabled,
the lspcon's implementation returns its active state. (we expect enabled
infoframe states of HW.) It leads to pipe state mismatch error
when ddi_get_config is called.

Because the current implementation of lspcon is not ready to support
readout infoframes, we need to return 0 here.

In order to support readout to lspcon, we need to implement read_infoframe
and infoframes_enabled. And set_infoframes also have to set an appropriate
bit on crtc_state->infoframes.enable

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-11-gwan-gyeong.mun@intel.com

Lots of enc_to_foo(&encoder->base) around. Simplify by passing
in the intel_encoder instead.

@find@
identifier F =~ "^enc_to_.*";
identifier E;
@@
F(struct drm_encoder *E)
{
...
}

@@
identifier find.F;
identifier find.E;
@@
F(
- struct drm_encoder *E
+ struct intel_encoder *encoder
  )
{
<...
- E
+ &encoder->base
...>
}

@@
identifier find.F;
expression E;
@@
- F(E)
+ F(to_intel_encoder(E))

@@
expression E;
@@
- to_intel_encoder(&E->base)
+ E
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-4-ville.syrjala@linux.intel.comReviewed-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>

Split up crtc_state->base to hw where appropriate. This is done using the following patch:

@@
struct intel_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-T->base.x
+T->hw.x

@@
struct drm_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-to_intel_crtc_state(T)->base.x
+to_intel_crtc_state(T)->hw.x
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-4-maarten.lankhorst@linux.intel.com

Everything about the file is about display, and mostly about types
related to display. Move under display/ as intel_display_types.h to
reflect the facts.

There's still plenty to clean up, but start off with moving the file
where it logically belongs and naming according to contents.

v2: fix the include guard name in the renamed file
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806113933.11799-1-jani.nikula@intel.com

Add a new subdirectory for display code, and start off by moving
modesetting output/encoder code. Judging by the include changes, this is
a surprisingly clean operation.

v2:
- move intel_sdvo_regs.h too
- use tabs for Makefile	file lists and sort them

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-2-jani.nikula@intel.com

It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.

Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f86f9beed730eaad0bdcc18b18817b3d221e16e2.1554461791.git.jani.nikula@intel.com

It used to be handy that we only had a couple of headers, but over time
intel_drv.h has become unwieldy. Extract declarations to a separate
header file corresponding to the implementation module, clarifying the
modularity of the driver.

Ensure the new header is self-contained, and do so with minimal further
includes, using forward declarations as needed. Include the new header
only where needed, and sort the modified include directives while at it
and as needed.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b01cae3b5307d31c34de2321d6d2913f1cc39a12.1554461791.git.jani.nikula@intel.com

Add code to read the infoframes from the video DIP and unpack them into
the crtc state.

v2: Make the read funcs return void (Daniel)
    Drop the duplicate infoframe enabled checks (Daniel)
    Add a FIXME for lspcon infoframe readout
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-6-ville.syrjala@linux.intel.com

Store the infoframes in the crtc state and precompute them in
.compute_config(). While precomputing we'll also fill out the
inforames.enable bitmask appropriately.

v2: Drop the null packet stuff (Daniel)
    Add a FIXME for lspcon
v3: .compute_config() now returns int
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-5-ville.syrjala@linux.intel.com

We want to start tracking which infoframes are enabled, so let's replace
the boolean flag with a bitmask.

We'll abstract the bitmask so that it's not platform dependent. That
will allow us to examine the bitmask later in platform independent code.

v2: Don't map VIDEO_DIP_ENABLE to the null packet (Daniel)
    Put a FIXME in the lspcon function
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-3-ville.syrjala@linux.intel.com

Mixed C99 and kernel types use is getting ugly.	Prefer kernel types.

sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0c2d399bfb8fd9f90c7899eaaa0a9cab82f0d68d.1547629303.git.jani.nikula@intel.com

Move the CEA-861 QS bit handling entirely into the edid code. No
need to bother the drivers with this.

Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: Eric Anholt <eric@anholt.net> (supporter:DRM DRIVERS FOR VC4)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NEric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-4-ville.syrjala@linux.intel.com

Make life easier for drivers by simply passing the connector
to drm_hdmi_avi_infoframe_from_display_mode() and
drm_hdmi_avi_infoframe_quant_range(). That way drivers don't
need to worry about is_hdmi2_sink mess.

v2: Make is_hdmi2_sink() return true for sil-sii8620
    Adapt to omap/vc4 changes

Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108172828.15184-1-ville.syrjala@linux.intel.com

We no longer change LSPCON into PCON mode if it boots up in
LS mode. This was broken by some code shuffling in
commit 96e35598 ("drm/i915: Check LSPCON vendor OUI").

I actually can't see a reason why that code shuffling had
to be done. The commit msg notes it but doesn't justify it
in any way. But I guess we'll keep the code in its current
place anyway and just make the "switch to PCON mode" part
effective once again.

Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Tested-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Fixes: 96e35598 ("drm/i915: Check LSPCON vendor OUI")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107171821.27862-1-ville.syrjala@linux.intel.comReviewed-by: NShashank Sharma <shashank.sharma@intel.com>

LSPCON chips can generate YCBCR outputs, if asked nicely :).

In order to generate YCBCR 4:2:0 outputs, a source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:2:0 in AVI infoframes

Whereas for YCBCR 4:4:4 outputs, the source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:4:4 in AVI infoframes

So for both 4:2:0 as well as 4:4:4 outputs, we are driving the
pipe for YCBCR 4:4:4 output, but AVI infoframe's color space
information indicates LSPCON FW to start scaling down from YCBCR
4:4:4 and generate YCBCR 4:2:0 output. As the scaling is done by
LSPCON device, we need not to reserve a scaler for 4:2:0 outputs.

V2: rebase
V3: Addressed review comments from Ville
    - add enum crtc_output_format instead of bool ycbcr420
    - use crtc_output_format=4:4:4 for modeset of LSPCON 4:2:0 output
      cases in this way we will have YCBCR 4:4:4 framework ready (except
      the ABI part)
V4: Added r-b from Maarten (for v3)
    Addressed review comments from Ville:
    - Do not add a non-atomic state variable to determine lspcon output.
      Instead add bool in CRTC state to indicate lspcon based scaling.
V5: Addressed review comments from Ville:
    - Change the state bool name from external scaling to something more
      relavent.
    - Keep the info and adjusted_mode structures const.
    - use crtc_state instead of pipe_config.
    - Push all the config change into lspcon_ycbcr420_config function.
V6: Rebase, small changes to accommodate changes in patch 2.
V7: Fixed checkpatch warnings for alignment
V8: Rebase

    PS: Ignored following warnings to match the current formatting:
    drm/i915: Add YCBCR 4:2:0/4:4:4 support for LSPCON
     -:53: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
    #53: FILE: drivers/gpu/drm/i915/i915_reg.h:8721:
    +#define  TRANS_MSA_SAMPLING_444        (2<<1)
                                          ^
    -:54: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
    #54: FILE: drivers/gpu/drm/i915/i915_reg.h:8722:
    +#define  TRANS_MSA_CLRSP_YCBCR         (2<<3)
V9: Rebase
V10: Rebase
V11: Rebase

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-8-git-send-email-shashank.sharma@intel.com

Different LSPCON vendors specify their custom methods to pass
AVI infoframes to the LSPCON chip, so does Parade tech.

This patch adds functions to arrange and write AVI infoframes
into Parade LSPCON chips.

V2: rebase
V3: Added r-b from Maarten
V4: rebase
V5: rebase
V6: rebase
V7: Fixed checkpatch warnings for alignment
V8: Rebase
V9: Rebase
V10: Rebase

Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-7-git-send-email-shashank.sharma@intel.com

LSPCON is a DP branch device, so LSPCON vendors define
specific methods to pass AVI infoframes to the the chip.
This patch adds:
- a generic wrapper function for writing AVI infoframes for
  all LSPCON devices.
- a vendor specific function to wrire AVI infoframes into
  MCA LSPCON devices.

V2: Rebase
V3: Added r-b from Maarten
V4: Rebase
V5: Rebase
V6: Rebase
V7: Fixed checkpatch warnings for alignment
V8: Rebase
V9: Added the retry logic, with 50ms incremental delays while
    writing AVI IF
V10: Changed the return value check
V11: Fixed checkpatch warning
V12: Rebase

Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-6-git-send-email-shashank.sharma@intel.com

In order to pass AVI infoframes to LSPCON devices, a source has to
write them in a vendor recommended method and location.

This patch series:
- adds generic LSPCON infoframe setup functions.
- registers these functions into existing AVI infoframe framework.
- triggers these functions from modeset sequence.

Next patches in the series will add vendor specific code.

V2: Added new parameter to align with new definition of
    drm_hdmi_avi_infoframe_quant_range
V3: Added r-b from Maarten (for V2)
    Added new parameter output_format in struct lspcon to accommodate
    Ville's review comments on last patch of the series
V4: Addressed Ville's review comment
    - Do not add output_format in LSPCON state, as its non-atomic. Add
      this into CRTC state (added in a later patch).
V5: Rebase
V6: Rebase
V7: Rebase
V8: Rebase
V9: Rebase
V10: Rebase
V11: Accommodated rebasing changes in intel_git_port fptrs (set_infoframes and infoframe_enabled)

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-5-git-send-email-shashank.sharma@intel.com

Intel LSPCON chip is provided by 2 vendors:
- Megachips America (MCA)
- Parade technologies (Parade tech)

Its important to know the vendor of this chip, as the address to
write AVI infoframes is different for those two.

This patch reads the vendor OUI signature, and marks into LSPCON
encoder structure for future usages.

This patch also does a small re-arrangement of the code, by moving
lspcon mode change into probe function.

V2: Use dp->desc for OUI detection, dont add a helper for this
    (Ville)
V3: Rebase, Added r-b from Maarten
V4: Rebase
V5: Rebase
V6: Rebase
V7: Rebase
V8: Rebase
V9: Rebase
V10: Rebase

Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NLankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-4-git-send-email-shashank.sharma@intel.com

100 ms is not enough time for the LSPCON adapter on Intel NUC devices to
settle. This causes dropped display modes at boot or screen reconfiguration.
Empirical testing can reproduce the error up to a timeout of 190 ms. Basic
boot and stress testing at 200 ms has not (yet) failed.

Increase timeout to 400 ms to get some margin of error.

Changes from v1:
The initial suggestion of 1000 ms was lowered due to concerns about delaying
valid timeout cases.
Update patch metadata.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107503
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1570392
Fixes: 357c0ae9 ("drm/i915/lspcon: Wait for expected LSPCON mode to settle")
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v4.11+
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NFredrik Schön <fredrik.schon@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817200728.8154-1-fredrik.schon@gmail.com
(cherry picked from commit 59f1c8ab)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

100 ms is not enough time for the LSPCON adapter on Intel NUC devices to
settle. This causes dropped display modes at boot or screen reconfiguration.
Empirical testing can reproduce the error up to a timeout of 190 ms. Basic
boot and stress testing at 200 ms has not (yet) failed.

Increase timeout to 400 ms to get some margin of error.

Changes from v1:
The initial suggestion of 1000 ms was lowered due to concerns about delaying
valid timeout cases.
Update patch metadata.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107503
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1570392
Fixes: 357c0ae9 ("drm/i915/lspcon: Wait for expected LSPCON mode to settle")
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v4.11+
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NFredrik Schön <fredrik.schon@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817200728.8154-1-fredrik.schon@gmail.com

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1e132575785d9b615208eb60ee5e388df5991172.1528794959.git.jani.nikula@intel.com

Let's try to simplify this mapping to hpd_pin -> bit
instead using port.
So for CNL with port F where we have this port using
hdp_pin and bits of other ports we don't need to duplicated
the mapping.

But for now this is only a re-org with no functional change
expected.

v2: Add missing lines and nuke @port reference from code
    documentation. (Ville)

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-7-rodrigo.vivi@intel.com

We read the dp dual mode Adapter identifier to detect the
LSPCON device. It's been observed from the CI testing that in
few cases, this read can get delayed or fail. For such scenarios,
LSPCON vendors suggest to retry the read operation.

This patch adds retry in the probe function, while reading
LSPCON identifier.

V3: added this patch in the series

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102294
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102295
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102359
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103186
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507630064-17908-4-git-send-email-shashank.sharma@intel.com

Our current logic to read LSPCON's current mode, stops retries and
breaks wait-loop, if it gets LSPCON_MODE_INVALID as return from the
core function. This doesn't allow us to try reading the mode again.

This patch removes this condition and allows retries reading
the currnt mode until timeout.

This also fixes/prevents some of the noise in form of debug messages
while running IGT CI test cases.

V2: rebase, added r-b
V2: changed some debug message levels from debug->error and
    error->debug in lspcon_get_current_mode function.
V3: Rebase

Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102294
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102295
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102359
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103186Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NMahesh Kumar <Mahesh1.kumar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507630064-17908-3-git-send-email-shashank.sharma@intel.com

When LSPCON support was extended to CNL
one part was missed on lspcon_init.

So, instead of adding check per platform on lspcon_init
let's use HAS_LSPCON that is already there for that
purpose.

Fixes: ff15947e ("drm/i915/cnl: LSPCON support is gen9+")
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170816030403.11368-1-rodrigo.vivi@intel.com
(cherry picked from commit acf58d4e)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

When LSPCON support was extended to CNL
one part was missed on lspcon_init.

So, instead of adding check per platform on lspcon_init
let's use HAS_LSPCON that is already there for that
purpose.

Fixes: ff15947e ("drm/i915/cnl: LSPCON support is gen9+")
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170816030403.11368-1-rodrigo.vivi@intel.com

Switch to using the common DP helpers instead of using our own.

v2: also remove leftover struct intel_dp_desc (Daniel)
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

During system resume time initialization the HPD level on LSPCON ports
can stay low for an extended amount of time, leading to failed AUX
transfers and LSPCON initialization. Fix this by waiting for HPD to get
asserted.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99178
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-3-git-send-email-imre.deak@intel.com
(cherry picked from commit 390b4e00)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

This effectively reverts
commit 489375c8
Author: Imre Deak <imre.deak@intel.com>
Date:   Mon Oct 24 19:33:31 2016 +0300

    drm/i915/lspcon: Add workaround for resuming in PCON mode

The workaround was added without considering that HPD is low during
the failed AUX transfers the WA fixed. Since the previous patch we
wait for HPD to get asserted. My tests also show that this happens
_after_ the DPCD reads start to return correct values. This
suggests that we don't need this WA any more, let's try to remove
it to reduce the clutter.

Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-4-git-send-email-imre.deak@intel.com

During system resume time initialization the HPD level on LSPCON ports
can stay low for an extended amount of time, leading to failed AUX
transfers and LSPCON initialization. Fix this by waiting for HPD to get
asserted.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99178
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485509961-9010-3-git-send-email-imre.deak@intel.com

All callers asked for a forced change but the function ignored this
parameter. It doesn't seem to be necessary to force the change in any
case so let's just remove the parameter.

Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479755707-29596-5-git-send-email-imre.deak@intel.com

Some LSPCON adaptors may return an incorrect LSPCON mode right after
waking from DP Sleep state. This is the case at least for the ParadTech
PS175 adaptor, both when waking because of exiting the DP Sleep to
active state, or due to any other AUX CH transfer. We can determine the
current expected mode based on whether the DPCD area is accessible,
since according to the LSPCON spec this area is only accesible
in PCON mode.

This wait will avoid us trying to change the mode, while the current
expected mode hasn't settled yet and start link training before the
adaptor thinks it's in PCON mode after waking from DP Sleep state.

Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479755707-29596-4-git-send-email-imre.deak@intel.com

Some LSPCON adaptors won't properly wake up in response to an AUX
request after the adaptor was placed to a DP Sink Sleep state (via
writing 0x2 to DP_SET_POWER). Based on the DP 1.4 specification 5.2.5,
the sink may place the AUX CH into a low-power state while in Sleep
state, but should wake it up in response to an AUX request within 1-20ms
(answering with AUX defers while waking it up). As opposed to this at
least the ParadTech PS175 adaptor won't fully wake in response to the
first I2C-over-AUX access and will occasionally ignore the offset in I2C
messages. This can result in accessing the DDC register at offset 0
regardless of the specified offset and the LSPCON detection failing.

To fix this do an initial dummy read from the DPCD area. The PS175 will
defer this access until it's fully woken (taking ~150ms) making sure the
following I2C-over-AUX accesses will work correctly.

Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=98353Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479755707-29596-2-git-send-email-imre.deak@intel.com

On my APL the LSPCON firmware resumes in PCON mode as opposed to the
expected LS mode. It also appears to be in a state where AUX DPCD reads
will succeed but return garbage recovering only after a few hundreds of
milliseconds. After the recovery time DPCD reads will result in the
correct values and things will continue to work. If I2C over AUX is
attempted during this recovery time (implying an AUX write transaction)
the firmware won't recover and will stay in this broken state.

As a workaround check if the firmware is in PCON state after resume and
if so wait until the correct DPCD values are returned. For this we
compare the branch descriptor with the one we cached during init time.
If the firmware was in the LS state, we skip the w/a and continue as
before.

v2:
- Use the DP descriptor value cached in intel_dp. (Jani)
- Get to intel_dp using container_of(), instead of a cached ptr.
  (Shashank)
- Use usleep_range() instead of msleep().

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98353
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477326811-30431-9-git-send-email-imre.deak@intel.com

We can use the container_of() magic to get to the DDC adapter, so no
need for caching a pointer to it. We'll also need to get at the intel_dp
ptr in the following patch, so add a helper that can be used for both
purposes.

Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477326811-30431-8-git-send-email-imre.deak@intel.com

As for external DP sink and branch devices read and print the DP
descriptor for eDP and LSPCON devices as well to aid debugging.

v2:
- Split out this change to a separate patch. (Jani)

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477326811-30431-7-git-send-email-imre.deak@intel.com