Fixes: c1cf79ca ("drm/amdgpu: use IP discovery table for renoir")

This nullptr issue should be specific on the Renoir series during try access the PWR_MISC_CNTL_STATUS
when PWR IP not been detected by discovery table. Moreover the PWR IP not existing in Renoir series is
expected therefore just avoid access PWR register in Renoir series.
Signed-off-by: NPrike.Liang <Prike.Liang@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Just check for APU.
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add some APU flags to simplify handling of different APU
variants.  It's easier to understand the special cases
if we use names flags rather than checking device ids and
silicon revisions.

v2: rebase on latest code
Acked-by: NEvan Quan <evan.quan@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Compute IBs need this too.

v2: split out version bump
v3: squash in emit frame count fixes
Signed-off-by: NMarek Olšák <marek.olsak@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Implement the .mem_sync hook defined earlier.

v2: Rename functions
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NLuben Tuikov <luben.tuikov@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

On my raven1 system (rev c6) with VBIOS 113-RAVEN-114 GFXOFF is
not stable (resulting in large block tiling noise in some applications).

Disabling GFXOFF via the quirk list fixes the problems for me.
Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

As this is already properly handled in amdgpu_gfx_off_ctrl(). In fact,
this unnecessary cancel_delayed_work_sync may leave a small time window
for race condition and is dangerous.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

With previous golden settings, compute task can't use
reserved LDS (32K) on CU0 and CU1. On 64K LDS system,
if compute work group allocate more than 32K LDS, then
it can't be dispatched to CU0 and CU1 because of the
reservation. This enables compute task to use reserved
LDS on CU0 and CU1.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NFelix Kuehling <felix.kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>

Since commit "Move to a per-IB secure flag (TMZ)",
we've been seeing hangs in GFX. We need to send
FRAME CONTROL stop/start back-to-back, every time
we flip the TMZ flag. That is, when we transition
from TMZ to non-TMZ we have to send a stop with
TMZ followed by a start with non-TMZ, and
similarly for transitioning from non-TMZ into TMZ.

This patch implements this, thus fixing the GFX
hang.

v1 -> v2:
As suggested by Luben, and accept part of implemetation from this patch:
- Put "secure" closed to the loop and use optimization
- Change "secure" to bool again, and move "secure == -1" out of loop.
v3: Small fixes/optimizations.
Reported-and-Tested-by: NPierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NLuben Tuikov <luben.tuikov@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Move from a per-CS secure flag (TMZ) to a per-IB
secure flag.
Signed-off-by: NLuben Tuikov <luben.tuikov@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Implement an accessor of adev->tmz.enabled. Let not
code around access it as "if (adev->tmz.enabled)"
as the organization may change. Instead...

Recruit "bool amdgpu_is_tmz(adev)" to return
exactly this Boolean value. That is, this function
is now an accessor of an already initialized and
set adev and adev->tmz.

Add "void amdgpu_gmc_tmz_set(adev)" to check and
set adev->gmc.tmz_enabled at initialization
time. After which one uses "bool
amdgpu_is_tmz(adev)" to query whether adev
supports TMZ.

Also, remove circular header file include.

v2: Remove amdgpu_tmz.[ch] as requested.
v3: Move TMZ into GMC.
Signed-off-by: NLuben Tuikov <luben.tuikov@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch expands the context control function to support trusted flag while we
want to set command buffer in trusted mode.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch expands the emit_tmz function to support trusted flag while we want
to set command buffer in trusted mode.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fixes coccicheck warning:

drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c:2534:2-3: Unneeded semicolon
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZheng Bin <zhengbin13@huawei.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>

Wait for the oldest sequence on the ring
to be signaled in order to make sure there
will be no command overrun.

v2: fix coding stype and remove abs operation
v3: remove the initialization of variable r
Signed-off-by: NYintian Tao <yttao@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

According to the current kiq read register method,
there will be race condition when using KIQ to read
register if multiple clients want to read at same time
just like the expample below:
1. client-A start to read REG-0 throguh KIQ
2. client-A poll the seqno-0
3. client-B start to read REG-1 through KIQ
4. client-B poll the seqno-1
5. the kiq complete these two read operation
6. client-A to read the register at the wb buffer and
   get REG-1 value

Therefore, use amdgpu_device_wb_get() to request reg_val_offs
for each kiq read register.

v2: fix the error remove
v3: fix the print typo
v4: remove unused variables
Signed-off-by: NYintian Tao <yttao@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

In pp_one_vf mode avoid the extra overhead and read/write the
registers without the KIQ.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NMonk Liu <monk.liu@amd.com>
Acked-by: NYintian Tao <yintian.tao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fix screen corruption with firefox.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=207171Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fix screen corruption with firefox.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=207171Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Prefix RAS message printing in GFX IP with PCI device info,
which assists the debug in multiple GPU case.
Signed-off-by: NGuchun Chen <guchun.chen@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Make the fw_write_wait default case true since presumably all new
gfx9 asics will have updated firmware. That is using unique WAIT_REG_MEM
packet with opration=1.
Signed-off-by: NAaron Liu <aaron.liu@amd.com>
Tested-by: NAaron Liu <aaron.liu@amd.com>
Tested-by: NYuxian Dai <Yuxian.Dai@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Generate HW IP's sched_list in amdgpu_ring_init() instead of
amdgpu_ctx.c. This makes amdgpu_ctx_init_compute_sched(),
ring.has_high_prio and amdgpu_ctx_init_sched() unnecessary.
This patch also stores sched_list for all HW IPs in one big
array in struct amdgpu_device which makes amdgpu_ctx_init_entity()
much more leaner.

v2:
fix a coding style issue
do not use drm hw_ip const to populate amdgpu_ring_type enum

v3:
remove ctx reference and move sched array and num_sched to a struct
use num_scheds to detect uninitialized scheduler list

v4:
use array_index_nospec for user space controlled variables
fix possible checkpatch.pl warnings
Signed-off-by: NNirmoy Das <nirmoy.das@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Make the fw_write_wait default case true since presumably all new
gfx9 asics will have updated firmware. That is using unique WAIT_REG_MEM
packet with opration=1.
Signed-off-by: NAaron Liu <aaron.liu@amd.com>
Tested-by: NAaron Liu <aaron.liu@amd.com>
Tested-by: NYuxian Dai <Yuxian.Dai@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

When we stop the HW for example for GPU reset we should not stop the
front-end scheduler. Otherwise we run into intermediate failures during
command submission.

The scheduler should only be stopped in very few cases:
1. We can't get the hardware working in ring or IB test after a GPU reset.
2. The KIQ scheduler is not used in the front-end and should be disabled during GPU reset.
3. In amdgpu_ring_fini() when the driver unloads.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NNirmoy Das <nirmoy.das@amd.com>
Test-by: NDennis Li <dennis.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Clean up the smu10, smu12, and gfx9 drivers to use headers for
registers instead of hardcoding in the C source files.
Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We have three ib pools, they are normal, VM, direct pools.

Any jobs which schedule IBs without dependence on gpu scheduler should
use DIRECT pool.

Any jobs schedule direct VM update IBs should use VM pool.

Any other jobs use NORMAL pool.

v2: squash in coding style fix
Signed-off-by: Nxinhui pan <xinhui.pan@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

the HPD bo size calculation error.
the "mem.size" can't present actual BO size all time.
Signed-off-by: NKevin Wang <kevin1.wang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NChristian König <Christian.Koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Set ComputePGMRSRC1.VGPRS as 0x3f to clear all ArcVGPRs.
Signed-off-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

There are spelling mistakes in pr_err messages and a comment. Fix these.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

clang warns:

drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c:754:6: warning: variable 'shadow'
is used uninitialized whenever 'if' condition is
false [-Wsometimes-uninitialized]
        if (offset == grbm_cntl || offset == grbm_idx)
            ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c:757:6: note: uninitialized use
occurs here
        if (shadow) {
            ^~~~~~
drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c:754:2: note: remove the 'if' if
its condition is always true
        if (offset == grbm_cntl || offset == grbm_idx)
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c:738:13: note: initialize the
variable 'shadow' to silence this warning
        bool shadow;
                   ^
                    = 0
1 warning generated.

shadow is only assigned in one condition and used as the condition for
another if statement; combine the two if statements and remove shadow
to make the code cleaner and resolve this warning.

Fixes: 2e0cc4d4 ("drm/amdgpu: revise RLCG access path")
Link: https://github.com/ClangBuiltLinux/linux/issues/936Suggested-by: NJoe Perches <joe@perches.com>
Reviewed-by: NNick Desaulniers <ndesaulniers@google.com>
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

what changed:
1)provide new implementation interface for the rlcg access path
2)put SQ_CMD/SQ_IND_INDEX to GFX9 RLCG path to let debugfs's reg_op
function can access reg that need RLCG path help

now even debugfs's reg_op can used to dump wave.
tested-by: NMonk Liu <monk.liu@amd.com>
tested-by: NZhou pengju <pengju.zhou@amd.com>
Signed-off-by: NZhou pengju <pengju.zhou@amd.com>
Signed-off-by: NMonk Liu <Monk.Liu@amd.com>
Reviewed-by: NEmily Deng <Emily.Deng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

AccVGPRs are newly added in arcturus. Before reading these
registers, they should be initialized. Otherwise edc error
happens, when RAS is enabled.

v2: reuse the existing logical to calculate register size
Signed-off-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

disallow the logical to be enabled on platforms that
don't support gfx ras at this stage, like sriov skus,
dgpu with legacy ras.etc
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NMonk Liu <monk.liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

AMDGPU statically sets priority for compute queues
at initialization so remove all the functions
responsible for changing compute queue priority dynamically.
Signed-off-by: NNirmoy Das <nirmoy.das@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We were changing compute ring priority while rings were being used
before every job submission which is not recommended. This patch
sets compute queue priority at mqd initialization for gfx8, gfx9 and
gfx10.

Policy: make queue 0 of each pipe as high priority compute queue

High/normal priority compute sched lists are generated from set of high/normal
priority compute queues. At context creation, entity of compute queue
get a sched list from high or normal priority depending on ctx->priority
Signed-off-by: NNirmoy Das <nirmoy.das@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The TDR will be randomly failed due to compute ring
test failure. If the compute ring wptr & 0x7ff(ring_buf_mask)
is 0x100 then after map mqd the compute ring rptr will be
synced with 0x100. And the ring test packet size is also 0x100.
Then after invocation of amdgpu_ring_commit, the cp will not
really handle the packet on the ring buffer because rptr is equal to wptr.
Signed-off-by: NYintian Tao <yttao@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NMonk Liu <Monk.Liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

HDP ras error counters are dirty ones after cold reboot
Read operation is needed to reset them to 0
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NTao Zhou <tao.zhou1@amd.com>
Reviewed-by: NGuchun Chen <guchun.chen@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

GFX ras error counters are dirty ones after cold reboot
Read operation is needed to reset them to 0
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NTao Zhou <tao.zhou1@amd.com>
Reviewed-by: NGuchun Chen <guchun.chen@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

1)for gfx IB test we shouldn't insert DE meta data

2)we should make sure IB test finished before we
send event 3 to hypervisor otherwise the IDLE from
event 3 will preempt IB test, which is not designed
as a compatible structure for MCBP
Signed-off-by: NMonk Liu <Monk.Liu@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The TDR will be randomly failed due to compute ring
test failure. If the compute ring wptr & 0x7ff(ring_buf_mask)
is 0x100 then after map mqd the compute ring rptr will be
synced with 0x100. And the ring test packet size is also 0x100.
Then after invocation of amdgpu_ring_commit, the cp will not
really handle the packet on the ring buffer because rptr is equal to wptr.
Signed-off-by: NYintian Tao <yttao@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NMonk Liu <Monk.Liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>