Restart AutoNeg if we didn't get a valid result from previous run.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set XPCS Link as down when AutoNeg is enabled but it didn't finish with
success.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reset the XPCS upon probe stage so that we start it from well known
state.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For 10GKR rate, when link errors are found we need to return fault
status so that XPCS is correctly resumed.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a dual copper PHY with support for MII/GMII/RGMII on MAC side,
as well as a bunch of other features such as SyncE and Ring Resiliency.

I haven't tested interrupts and WoL, but I am confident that they work
since support is already present in the driver and the register map is
no different for this PHY.

PHY statistics work, PHY tunables appear to work, suspend/resume works.
Signed-off-by: NWes Li <wes.li@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver appears to be secretly enabling the RX clock skew
irrespective of PHY interface type, which is generally considered a big
no-no.

Make them configurable instead, and add TX internal delays when
necessary too.

While at it, configure a more canonical clock skew of 2.0 nanoseconds
than the current default of 1.1 ns.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The helper for configuring the pinout of the MII side of the PHY should
do so irrespective of whether RGMII delays are used or not. So accept
the ID, TXID and RXID variants as well, not just the no-delay RGMII
variant.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is nothing RX-specific about these clock skew values. So remove
"RX" from the name in preparation for the next patch where TX delays are
also going to be configured.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for configuring the RGMII skew delays in Rx and
Tx. The Rx and Tx skews are set based on the interface mode. By default
their configuration is set to the default value in hardware (0.2ns);
this means the driver do not rely anymore on the bootloader
configuration.

Then based on the interface mode being used, a 2ns delay is added:
- RGMII_ID adds it for both Rx and Tx.
- RGMII_RXID adds it for Rx.
- RGMII_TXID adds it for Tx.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for connecting VSC8584 PHYs to the MAC using
RGMII.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a5afc167 ("net: phy: mscc: add support for VSC8584 PHY")
introduced a call to 'phy_write' storing its return value to a variable
called 'ret'. But 'ret' never was checked for a possible error being
returned, and hence was not used at all. Fix this by checking the return
value and exiting the function if an error was returned.

As this does not fix a known bug, this commit is mostly cosmetic and not
sent as a fix.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At least some integrated PHY's in RTL8168/RTL8125 chip versions support
downshift, and the actual link speed can be read from a vendor-specific
register. Info about this register was provided by Realtek.
More details about downshift configuration (e.g. number of attempts)
aren't available, therefore the downshift tunable is not implemented.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement helpers for PCS accessed via the MII bus using 802.3 clause
45 cycles for 10GBASE-R. Only link up/down is supported, 10G full
duplex is assumed.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement helpers for PCS accessed via the MII bus using 802.3 clause
22 cycles, conforming to 802.3 clause 37 and Cisco SGMII specifications
for the advertisement word.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add APIs for modifying a MDIO device register, similar to the existing
phy_modify() group of functions, but at mdiobus level instead.  Adapt
__phy_modify_changed() to use the new mdiobus level helper.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid using BUG_ON() in the mdiobus accessors, prefering instead to use
WARN_ON_ONCE() and returning an error.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add XLGMII support for XPCS. This does not include Autoneg feature.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trigger the respective interrupt handler functionality only if the
related interrupt source bit is set.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

did_interrupt() clears the interrupt, therefore handle_interrupt() can
not check which event triggered the interrupt. To overcome this
constraint and allow more flexibility for customer interrupt handlers,
let's decouple handle_interrupt() from parts of the phylib interrupt
handling. Custom interrupt handlers now have to implement the
did_interrupt() functionality in handle_interrupt() if needed.

Fortunately we have just one custom interrupt handler so far (in the
mscc PHY driver), convert it to the changed API.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cosmetic commit fixing the MSCC PHY header defines and descriptions,
which were referring the to MSCC Ocelot MAC driver (see
drivers/net/ethernet/mscc/).
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch splits the MSCC driver into separate files, per
functionality, to improve readability and maintenance as the codebase
grew a lot. The MACsec code is moved to a dedicated mscc_macsec.c file,
the mscc.c file is renamed to mscc_main.c to keep the driver binary to
be named mscc and common definition are put into a new mscc.h header.

Most of the code was just moved around, except for a few exceptions:
- Header inclusions were reworked to only keep what's needed.
- Three helpers were created in the MACsec code, to avoid #ifdef's in
  the main C file: vsc8584_macsec_init, vsc8584_handle_macsec_interrupt
  and vsc8584_config_macsec_intr.

The patch should not introduce any functional modification.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MSCC PHY driver is growing, with lots of space consuming features
(firmware support, full initialization, MACsec...). It's becoming hard
to read and navigate in its source code. This patch moves the MSCC
driver to its own directory, without modifying anything, as a
preparation for splitting up its features into dedicated files.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add XLGMII interface and the list of XLGMII speeds to PHYLINK.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.

To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.

Fixes: 503ba7c6 ("net: phy: Avoid multiple suspends")
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Tested-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Synopsys DesignWare XPCS is an MMD that can manage link status,
auto-negotiation, link training, ...

In this commit we add basic support for XPCS using USXGMII interface and
Clause 73 Auto-negotiation.

This is highly tied with PHYLINK and can't be used without it. A given
ethernet driver can use the provided callbacks to add the support for
XPCS.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We may have cases where MAC or PCS do not support Autoneg. Check if it
is supported after validate callback is called.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

USXGMII also supports these missing backplane speeds.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently ipq806x soc use generic bitbang driver to
comunicate with the gmac ethernet interface.
Add a dedicated driver created by chunkeey to fix this.
Co-developed-by: NChristian Lamparter <chunkeey@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@gmail.com>
Signed-off-by: NAnsuel Smith <ansuelsmth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Place the 88x3310 into powersaving mode when probing, which saves 600mW
per PHY. For both PHYs on the Macchiatobin double-shot, this saves
about 10% of the board idle power.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the energy detect power down tunable, which saves
around 600mW when the link is down. The 88x3310 supports off, rx-only
and NLP every second. Enable EDPD by default for 88x3310.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for controlling the MDI-X state of the PHY.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should improve the error message when the PHY validate in the MAC
driver failed. I ran into this problem multiple times that I put wrong
interface values into the device tree and was searching why it is
failing with -22 (-EINVAL). This should make it easier to spot the
problem.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

719655a1 ("net: phy: Replace phy driver features u32 with link_mode
bitmap") was a bit over-eager and also removed the second phy driver's
name, resulting in a nasty OOPS on registration:

[    1.319854] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 804dd50c, ra == 804dd4f0
[    1.330859] Oops[#1]:
[    1.333138] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.22 #0
[    1.339217] $ 0   : 00000000 00000001 87ca7f00 805c1874
[    1.344590] $ 4   : 00000000 00000047 00585000 8701f800
[    1.349965] $ 8   : 8701f800 804f4a5c 00000003 64726976
[    1.355341] $12   : 00000001 00000000 00000000 00000114
[    1.360718] $16   : 87ca7f80 00000000 00000000 80639fe4
[    1.366093] $20   : 00000002 00000000 806441d0 80b90000
[    1.371470] $24   : 00000000 00000000
[    1.376847] $28   : 87c1e000 87c1fda0 80b90000 804dd4f0
[    1.382224] Hi    : d1c8f8da
[    1.385180] Lo    : 5518a480
[    1.388182] epc   : 804dd50c kset_find_obj+0x3c/0x114
[    1.393345] ra    : 804dd4f0 kset_find_obj+0x20/0x114
[    1.398530] Status: 10008703 KERNEL EXL IE
[    1.402833] Cause : 00800008 (ExcCode 02)
[    1.406952] BadVA : 00000000
[    1.409913] PrId  : 0002a075 (Broadcom BMIPS4350)
[    1.414745] Modules linked in:
[    1.417895] Process swapper/0 (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000)
[    1.426214] Stack : 87cec000 80630000 80639370 80640658 80640000 80049af4 80639fe4 8063a0d8
[    1.434816]         8063a0d8 802ef078 00000002 00000000 806441d0 80b90000 8063a0d8 802ef114
[    1.443417]         87cea0de 87c1fde0 00000000 804de488 87cea000 8063a0d8 8063a0d8 80334e48
[    1.452018]         80640000 8063984c 80639bf4 00000000 8065de48 00000001 8063a0d8 80334ed0
[    1.460620]         806441d0 80b90000 80b90000 802ef164 8065dd70 80620000 80b90000 8065de58
[    1.469222]         ...
[    1.471734] Call Trace:
[    1.474255] [<804dd50c>] kset_find_obj+0x3c/0x114
[    1.479141] [<802ef078>] driver_find+0x1c/0x44
[    1.483665] [<802ef114>] driver_register+0x74/0x148
[    1.488719] [<80334e48>] phy_driver_register+0x9c/0xd0
[    1.493968] [<80334ed0>] phy_drivers_register+0x54/0xe8
[    1.499345] [<8001061c>] do_one_initcall+0x7c/0x1f4
[    1.504374] [<80644ed8>] kernel_init_freeable+0x1d4/0x2b4
[    1.509940] [<804f4e24>] kernel_init+0x10/0xf8
[    1.514502] [<80018e68>] ret_from_kernel_thread+0x14/0x1c
[    1.520040] Code: 1060000c  02202025  90650000 <90810000> 24630001  14250004  24840001  14a0fffb  90650000
[    1.530061]
[    1.531698] ---[ end trace d52f1717cd29bdc8 ]---

Fix it by readding the name.

Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add constants for the used interrupts bits. This avoids the magic
number for MII_VSC85XX_INT_MASK_MASK.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On all PHY drivers that implement did_interrupt() reading the interrupt
status bits clears them. This means we may loose an interrupt that
is triggered between calling did_interrupt() and phy_clear_interrupt().
As part of the fix make it a requirement that did_interrupt() clears
the interrupt.

The Fixes tag refers to the first commit where the patch applies
cleanly.

Fixes: 49644e68 ("net: phy: add callback for custom interrupt handler to struct phy_driver")
Reported-by: NMichael Walle <michael@walle.cc>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: NAndre Przywara <andre.przywara@arm.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read the copper autonegotiation results from the copper specific
status register, rather than decoding the advertisements. Reading
what the link is actually doing will allow us to support downshift
modes.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't attempt to interpret the PHY specific status register unless
the PHY is indicating that the resolution is valid.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware paths for the VSC8584 PHYs not not contain the leading
'microchip/' directory, as used in linux-firmware, resulting in an
error when probing the driver. This patch fixes it.

Fixes: a5afc167 ("net: phy: mscc: add support for VSC8584 PHY")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a missing shift for the media operation mode selection.
This does not fix the driver as the current operation mode (copper) has
a value of 0, but this wouldn't work for other modes.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>