MFD_ARIZONA_I2C and MFD_ARIZONA_SPI both select MFD_ARIZONA and all
three of those select MFD_CORE, this makes the selects of MFD_CORE in
MFD_ARIZONA_I2C and MFD_ARIZONA_SPI redundant, so we remove them.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The help text had a copy and paste error and refers to I2C in the SPI
section. This patch corrects this typo.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add support for the TPS65912 device. It provides communication
through I2C and contains the following components:

 - Regulators
 - Load switches
 - GPO controller
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

These drivers can be built as module, so make them depend on I2C rather
than I2C=y.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NAdam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The AXP223 is a new PMIC commonly paired with Allwinner A23/A33 SoCs.
It is functionally identical to AXP221; only the regulator default
voltage/status and the external host interface are different.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The axp20x driver assumes the device is i2c based. This is not the
case with later chips, which use a proprietary 2 wire serial bus
by Allwinner called "Reduced Serial Bus".

This patch follows the example of mfd/wm831x and splits it into
an interface independent core, and an i2c specific glue layer.
MFD_AXP20X and the new MFD_AXP20X_I2C are changed to tristate
symbols, allowing the driver to be built as modules.

Whitespace and other style errors in the moved i2c specific code
have been fixed. Included but unused header files are removed as
well.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds support for TPS65912 PMIC MFD core. It provides
communication through the I2C and SPI interfaces. It contains
the following components:

 - Regulators
 - GPIO controller
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The old tps65912 driver is being replaced, delete old driver.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Acked-by: NMark Brown <broonie@kernel.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This is the core driver for imx25 touchscreen/adc driver. The module
has one shared ADC and two different conversion queues which use the
ADC. The two queues are identical. Both can be used for general purpose
ADC but one is meant to be used for touchscreens.

This driver is the core which manages the central components and
registers of the TSC/ADC unit. It manages the IRQs and forwards them to
the correct components.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NDenis Carikli <denis@eukrea.com>
[ensure correct ADC clock depending on the IPG clock]
Signed-off-by: NJuergen Borleis <jbe@pengutronix.de>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Allow support for the DA9063 PMIC to be modular, cfr. DA9062, which
allows to decrease size of multi-platform kernels (e.g.
multi_v7_defconfig).
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the regmap configuration tables and
core MFD handling for the CS47L24 and WM1831 codecs.

Note that compared to the other Arizona codecs, these devices
do not have an LDO1 or micsupp regulators, extcon driver, or
the DCVDD isolation control.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This is required since
commit 7e507119 ("mfd: tps6105x: Use i2c regmap to access registers").
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

rts522a(rts5227s) is derived from rts5227, and mainly same with rts5227.
Add it to file mfd/rts5227.c to support this chip.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The driver depends on ARCH_NOMADIK but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.

That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: NLuis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This driver supports the new Atmel Flexcom. The Flexcom is a wrapper which
integrates one SPI controller, one I2C controller and one USART. Only one
function can be enabled at a time. This driver selects the function once
for all, when the Flexcom is probed, according to the value of the new
"atmel,flexcom-mode" device tree property.

This driver has chosen to present the Flexcom to the system as a MFD so
the implementation is seamless for the existing Atmel SPI, I2C and USART
drivers.

Also the Flexcom embeds FIFOs: the latest patches of the SPI, I2C and
USART drivers take advantage of this new feature.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The MFD_CROS_EC symbol select CHROME_PLATFORMS and CROS_EC_PROTO but
that caused a Kconfig unmet direct dependencies warning since these
symbols could only be selected for X86 || ARM.

The fix it, the CHROME_PLATFORMS dependencies were relexed on commit
d12bbcd3 ("platform/chrome: Don't make CHROME_PLATFORMS depends
on X86 || ARM") but that was found to be wrong and the correct fix
is to add the needed dependencies to the MFD_CROS_EC config symbol.

There are only x86 and ARM based Chromebooks so to avoid showing up
the config option on unsupported platforms, make the symbol depend on
these architectures. Also add a || COMPILE_TEST so it can have build
coverage on other platforms.
Suggested-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The ChromeOS EC SPI and I2C transport drivers depends on CROS_EC_PROTO
but MFD_CROS_EC select CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.

Since these drivers already depend on MFD_CROS_EC and that config option
already selects CROS_EC_PROTO, there is no need to make them explicitly
depend on CROS_EC_PROTO since that dependency is already met.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the DMI system ID of the Kontron COMe-bBL6 and COME-cBW6
boards to the Kontron PLD driver. The list of supported products in the
module description is also updated.
Signed-off-by: NMichael Brunner <michael.brunner@kontron.com>
Acked-by: NChristian Rauch <christian.rauch@kontron.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add MFD core driver support for DA9062
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The ChromeOS EC SPI transport driver has a dependency on OF because it
uses some OF helpers from the <linux/of.h> header. But there isn't a
need for an explicit dependency since the header has stub functions if
CONFIG_OF is not defined.

Also, MFD_CROS_EC_SPI already depends on MFD_CROS_EC which in turn has
a dependency on OF so in practice can't be selected without CONFIG_OF.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The new coming Intel platforms such as Skylake will contain Sunrisepoint PCH.
The main difference to the previous platforms is that the LPSS devices are
compound devices where usually main (SPI, HSUART, or I2C) and DMA IPs are
present.

This patch brings the driver for such devices found on Sunrisepoint PCH.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The ChromeOS EC SPI transport driver has a dependency on OF because it
uses some OF helpers from the <linux/of.h> header. But there isn't a
need for an explicit dependency since the header has stub functions if
CONFIG_OF is not defined.

Also, MFD_CROS_EC_SPI already depends on MFD_CROS_EC which in turn has
a dependency on OF so in practice can't be selected without CONFIG_OF.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This is needed as the CRC PMIC has support for Panel
enable/diable as gpio which needs 'gpiod_add_lookup_table'
and 'gpiod_remove_lookup_table' from gpiolib. This patch
can be squashed with below commit in topic/crc-pmic branch

    commit 61dd2ca2
    Author: Shobhit Kumar <shobhit.kumar@intel.com>
    Date:   Fri Jun 26 14:32:05 2015 +0530

    mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO
    signal

    On some Intel SoC platforms, the panel enable/disable signals
    are controlled by CRC PMIC. Add those control as a new GPIO in a
    lookup table for gpio-crystalcove chip during CRC driver load

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.

The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NŁukasz Stelmach <stlman@poczta.fm>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NGyungoh Yoo <jack.yoo@skyworksinc.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In Quark X1000, there's a single PCI device that provides both
an I2C controller and a GPIO controller. This MFD driver will
split the 2 devices for their respective drivers.

This patch is based on Josef Ahmad's initial work for Quark enabling.
Acked-by: NMichael Turquette <mturquette@linaro.org>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWeike Chen <alvin.chen@intel.com>
Signed-off-by: NRaymond Tan <raymond.tan@intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Since commit 0b271258(linux-next.git) this driver uses regmap_irq and so needs
to select REGMAP_IRQ.

This fixes the following compilation errors:
ERROR: "regmap_irq_get_domain" [drivers/mfd/rt5033.ko] undefined!
ERROR: "regmap_add_irq_chip" [drivers/mfd/rt5033.ko] undefined!
Signed-off-by: NArtem Savkov <asavkov@redhat.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds MAX77843 core/irq driver to support PMIC,
MUIC(Micro USB Interface Controller), Charger, Fuel Gauge,
LED and Haptic device.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds support for the MediaTek MT6397 PMIC. This is a
multifunction device with the following sub modules:

- Regulator
- RTC
- Audio codec
- GPIO
- Clock

It is interfaced to the host controller using SPI interface by a proprietary
hardware called PMIC wrapper or pwrap. MT6397 MFD is a child device of the
pwrap.

Signed-off-by: Flora Fu, MediaTek
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the DMI system ID of the Kontron COMe-cBL6 board to
the Kontron PLD driver. The list of supported products in the module
description is also updated.
Signed-off-by: NMichael Brunner <michael.brunner@kontron.com>
Acked-by: NChristian Rauch <christian.rauch@kontron.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds support for the Wolfson Microelectronics WM8280 and WM8281
codecs.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
[Lee: Minor fixup to remove potentially uninitialised variable. ]
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Driver for the Resource Power Manager (RPM) found in Qualcomm 8660, 8960
and 8064 based devices. The driver exposes resources that child drivers
can operate on; to implementing regulator, clock and bus frequency
drivers.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The driver is used only on Exynos based boards with DTS support.
After removal of board file support from max77686 and max77802 regulator
drivers, the MFD driver can be converted to DTS-only version. This
simplifies a little the code:
1. No dead (unused) entries in platform_data structure.
2. More code removed.
3. Regulator driver does not depend on allocated memory
   from MFD driver.
4. It makes also easier extending the regulator driver.

Add to the max77686 MFD driver dependency on CONFIG_OF because without
DTS the regulator drivers (max77686 and max77802) won't bind.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

DA9150 is a combined Charger and Fuel-Gauge IC, with additional
GPIO and GPADC functionality.
Signed-off-by: NAdam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds a new driver for Richtek RT5033 driver.
RT5033 is a Multifunction device which includes battery charger, fuel gauge,
flash LED current source, LDO and synchronous Buck converter. It is interfaced
to host controller using I2C interface.
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Acked-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>