With CONFIG_DMA_API_DEBUG enabled we get DMA unmapping warning in
various places of the mvneta driver, for example when putting down an
interface while traffic is passing through.

The issue is when using s/w buffer management, the Rx buffers are mapped
using dma_map_page but unmapped with dma_unmap_single. This patch fixes
this by using the right unmapping function.

Fixes: 562e2f46 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cong noted that we need the same checks introduced by commit 76c0ddd8
("ip6_tunnel: be careful when accessing the inner header")
even for ipv4 tunnels.

Fixes: c5441932 ("GRE: Refactor GRE tunneling code.")
Suggested-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Summary:

This appears to be necessary and sufficient change to enable `MPLS` on
`ip6gre` tunnels (RFC4023).

This diff allows IP6GRE devices to be recognized by MPLS kernel module
and hence user can configure interface to accept packets with mpls
headers as well setup mpls routes on them.

Test Plan:

Test plan consists of multiple containers connected via GRE-V6 tunnel.
Then carrying out testing steps as below.

- Carry out necessary sysctl settings on all containers

```
sysctl -w net.mpls.platform_labels=65536
sysctl -w net.mpls.ip_ttl_propagate=1
sysctl -w net.mpls.conf.lo.input=1
```

- Establish IP6GRE tunnels

```
ip -6 tunnel add name if_1_2_1 mode ip6gre \
  local 2401:db00:21:6048:feed:0::1 \
  remote 2401:db00:21:6048:feed:0::2 key 1
ip link set dev if_1_2_1 up
sysctl -w net.mpls.conf.if_1_2_1.input=1
ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link

ip -6 tunnel add name if_1_3_1 mode ip6gre \
  local 2401:db00:21:6048:feed:0::1 \
  remote 2401:db00:21:6048:feed:0::3 key 1
ip link set dev if_1_3_1 up
sysctl -w net.mpls.conf.if_1_3_1.input=1
ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link
```

- Install MPLS encap rules on node-1 towards node-2

```
ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \
  via inet 169.254.0.3 dev if_1_2_1
```

- Install MPLS forwarding rules on node-2 and node-3
```
// node2
ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1

// node3
ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1
```

- Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing
  towards 192.168.0.1 is via IP route directly towards node1 from node4)
```
ping 192.168.0.11
```

- tcpdump on interface to capture ping packets wrapped within MPLS
  header which inturn wrapped within IP6GRE header

```
16:43:41.121073 IP6
  2401:db00:21:6048:feed::1 > 2401:db00:21:6048:feed::2:
  DSTOPT GREv0, key=0x1, length 100:
  MPLS (label 32, exp 0, ttl 255) (label 64, exp 0, [S], ttl 255)
  IP 192.168.0.1 > 192.168.0.11:
  ICMP echo request, id 1208, seq 45, length 64

0x0000:  6000 2cdb 006c 3c3f 2401 db00 0021 6048  `.,..l<?$....!`H
0x0010:  feed 0000 0000 0001 2401 db00 0021 6048  ........$....!`H
0x0020:  feed 0000 0000 0002 2f00 0401 0401 0100  ......../.......
0x0030:  2000 8847 0000 0001 0002 00ff 0004 01ff  ...G............
0x0040:  4500 0054 3280 4000 ff01 c7cb c0a8 0001  E..T2.@.........
0x0050:  c0a8 000b 0800 a8d7 04b8 002d 2d3c a05b  ...........--<.[
0x0060:  0000 0000 bcd8 0100 0000 0000 1011 1213  ................
0x0070:  1415 1617 1819 1a1b 1c1d 1e1f 2021 2223  .............!"#
0x0080:  2425 2627 2829 2a2b 2c2d 2e2f 3031 3233  $%&'()*+,-./0123
0x0090:  3435 3637                                4567
```
Signed-off-by: NSaif Hasan <has@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-09-24

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Several fixes for BPF sockmap to only allow sockets being attached in
   ESTABLISHED state, from John.

2) Fix up the license to LGPL/BSD for the libc compat header which contains
   fallback helpers that libbpf and bpftool is using, from Jakub.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.

Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.

In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.

The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:

    sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
          / Raw(RandString(size=(4096-40))), iface="enp1s0")

Fixes: 018423e9 ("net: ethernet: aquantia: Add ring support code")
Reported-by: NFriedemann Gerold <f.gerold@b-c-s.de>
Reported-by: NMichael Rauch <michael@rauch.be>
Signed-off-by: NFriedemann Gerold <f.gerold@b-c-s.de>
Tested-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
netpoll: avoid capture effects for NAPI drivers

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC).

This capture, showing one ksoftirqd eating all cycles
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller() :

Most NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev()
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.

This patch series take care of the first round, we will
handle other drivers in future rounds.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

tun uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

nfp uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

bnxt uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

bnx2x uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

mlx5 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

mlx4 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

i40evf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

ice uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

igb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

ixgb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.

This also removes a problematic use of disable_irq() in
a context it is forbidden, as explained in commit
af3e0fcf ("8139too: Use disable_irq_nosync() in
rtl8139_poll_controller()")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
lasts for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

fm10k uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

ixgbevf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

ixgbe uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Reported-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NSong Liu <songliubraving@fb.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We want to allow NAPI drivers to no longer provide
ndo_poll_controller() method, as it has been proven problematic.

team driver must not look at its presence, but instead call
netpoll_poll_dev() which factorize the needed actions.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Acked-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller().

NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev()
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.

This patch allows netpoll_poll_dev() to process NAPI
contexts even for drivers not providing ndo_poll_controller(),
allowing for following patches in NAPI drivers.

Also we export netpoll_poll_dev() so that it can be called
by bonding/team drivers in following patches.
Reported-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use DECLARE_* not DEFINE_*

Fixes: 8360ed67 ("RDS: IB: Use DEFINE_PER_CPU_SHARED_ALIGNED for rds_ib_stats")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So it should not fail with EPERM even though it is no longer implemented...

This is a fix for:
  (userns)$ egrep ^Cap /proc/self/status
  CapInh: 0000003fffffffff
  CapPrm: 0000003fffffffff
  CapEff: 0000003fffffffff
  CapBnd: 0000003fffffffff
  CapAmb: 0000003fffffffff

  (userns)$ tcpdump -i usb_rndis0
  tcpdump: WARNING: usb_rndis0: SIOCETHTOOL(ETHTOOL_GUFO) ioctl failed: Operation not permitted
  Warning: Kernel filter failed: Bad file descriptor
  tcpdump: can't remove kernel filter: Bad file descriptor

With this change it returns EOPNOTSUPP instead of EPERM.

See also https://github.com/the-tcpdump-group/libpcap/issues/689

Fixes: 08a00fea "net: Remove references to NETIF_F_UFO from ethtool."
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns when two declarations' section attributes don't match.

net/rds/ib_stats.c:40:1: warning: section does not match previous
declaration [-Wsection]
DEFINE_PER_CPU_SHARED_ALIGNED(struct rds_ib_statistics, rds_ib_stats);
^
./include/linux/percpu-defs.h:142:2: note: expanded from macro
'DEFINE_PER_CPU_SHARED_ALIGNED'
        DEFINE_PER_CPU_SECTION(type, name,
PER_CPU_SHARED_ALIGNED_SECTION) \
        ^
./include/linux/percpu-defs.h:93:9: note: expanded from macro
'DEFINE_PER_CPU_SECTION'
        extern __PCPU_ATTRS(sec) __typeof__(type) name;
\
               ^
./include/linux/percpu-defs.h:49:26: note: expanded from macro
'__PCPU_ATTRS'
        __percpu __attribute__((section(PER_CPU_BASE_SECTION sec)))
\
                                ^
net/rds/ib.h:446:1: note: previous attribute is here
DECLARE_PER_CPU(struct rds_ib_statistics, rds_ib_stats);
^
./include/linux/percpu-defs.h:111:2: note: expanded from macro
'DECLARE_PER_CPU'
        DECLARE_PER_CPU_SECTION(type, name, "")
        ^
./include/linux/percpu-defs.h:87:9: note: expanded from macro
'DECLARE_PER_CPU_SECTION'
        extern __PCPU_ATTRS(sec) __typeof__(type) name
               ^
./include/linux/percpu-defs.h:49:26: note: expanded from macro
'__PCPU_ATTRS'
        __percpu __attribute__((section(PER_CPU_BASE_SECTION sec)))
\
                                ^
1 warning generated.

The initial definition was added in commit ec16227e ("RDS/IB:
Infiniband transport") and the cache aligned definition was added in
commit e6babe4c ("RDS/IB: Stats and sysctls") right after. The
definition probably should have been updated in net/rds/ib.h, which is
what this patch does.

Link: https://github.com/ClangBuiltLinux/linux/issues/114Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns that the address of a pointer will always evaluated as true
in a boolean context:

drivers/net/ethernet/mellanox/mlx4/eq.c:243:11: warning: address of
array 'eq->affinity_mask' will always evaluate to 'true'
[-Wpointer-bool-conversion]
        if (!eq->affinity_mask || cpumask_empty(eq->affinity_mask))
            ~~~~~^~~~~~~~~~~~~
1 warning generated.

Use cpumask_available, introduced in commit f7e30f01 ("cpumask: Add
helper cpumask_available()"), which does the proper checking and avoids
this warning.

Link: https://github.com/ClangBuiltLinux/linux/issues/86Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Smatch reports that devlink_dpipe_send_and_alloc_skb() frees the skb
on error so this is a double free.  We fixed a bunch of these bugs in
commit 7fe4d6dc ("devlink: Remove redundant free on error path") but
we accidentally overlooked this one.

Fixes: d9f9b9a4 ("devlink: Add support for resource abstraction")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function pci_create_slot() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().

Fixes: a15f2c08 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The backend handling for /proc/net/if_inet6 in addrconf.c doesn't properly
handle starting/stopping the iteration.  The problem is that at some point
during the iteration, an overflow is detected and the process is
subsequently stopped.  The item being shown via seq_printf() when the
overflow occurs is not actually shown, though.  When start() is
subsequently called to resume iterating, it returns the next item, and
thus the item that was being processed when the overflow occurred never
gets printed.

Alter the meaning of the private data member "offset".  Currently, when it
is not 0 (which only happens at the very beginning), "offset" represents
the next hlist item to be printed.  After this change, "offset" always
represents the current item.

This is also consistent with the private data member "bucket", which
represents the current bucket, and also the use of "pos" as defined in
seq_file.txt:
    The pos passed to start() will always be either zero, or the most
    recent pos used in the previous session.
Signed-off-by: NJeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netlbl_unlabel_addrinfo_get() assumes that if it finds the
NLBL_UNLABEL_A_IPV4ADDR attribute, it must also have the
NLBL_UNLABEL_A_IPV4MASK attribute as well. However, this is
not necessarily the case as the current checks in
netlbl_unlabel_staticadd() and friends are not sufficent to
enforce this.

If passed a netlink message with NLBL_UNLABEL_A_IPV4ADDR,
NLBL_UNLABEL_A_IPV6ADDR, and NLBL_UNLABEL_A_IPV6MASK attributes,
these functions will all call netlbl_unlabel_addrinfo_get() which
will then attempt dereference NULL when fetching the non-existent
NLBL_UNLABEL_A_IPV4MASK attribute:

Unable to handle kernel NULL pointer dereference at virtual address 0
Process unlab (pid: 31762, stack limit = 0xffffff80502d8000)
Call trace:
	netlbl_unlabel_addrinfo_get+0x44/0xd8
	netlbl_unlabel_staticremovedef+0x98/0xe0
	genl_rcv_msg+0x354/0x388
	netlink_rcv_skb+0xac/0x118
	genl_rcv+0x34/0x48
	netlink_unicast+0x158/0x1f0
	netlink_sendmsg+0x32c/0x338
	sock_sendmsg+0x44/0x60
	___sys_sendmsg+0x1d0/0x2a8
	__sys_sendmsg+0x64/0xb4
	SyS_sendmsg+0x34/0x4c
	el0_svc_naked+0x34/0x38
Code: 51001149 7100113f 540000a0 f9401508 (79400108)
---[ end trace f6438a488e737143 ]---
Kernel panic - not syncing: Fatal exception
Signed-off-by: NSean Tranchetti <stranche@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John Fastabend says:

====================
Eric noted that using the close callback is not sufficient
to catch all transitions from ESTABLISHED state to a LISTEN
state. So this series does two things. First, only allow
adding socks in ESTABLISH state and second use unhash callback
to catch tcp_disconnect() transitions.

v2: added check for ESTABLISH state in hash update sockmap as well
v3: Do not release lock from unhash in error path, no lock was
    used in the first place. And drop not so useful code comments
v4: convert,
	if (unhash()) return unhash(); return
     to if (unhash()) unhash(); return;

Thanks for reviewing Yonghong I carried your ACKs forward.
====================
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Ensure that sockets added to a sock{map|hash} that is not in the
ESTABLISHED state is rejected.

Fixes: 1aa12bdf ("bpf: sockmap, add sock close() hook to remove socks")
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NYonghong Song <yhs@fb.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

It is possible (via shutdown()) for TCP socks to go trough TCP_CLOSE
state via tcp_disconnect() without actually calling tcp_close which
would then call our bpf_tcp_close() callback. Because of this a user
could disconnect a socket then put it in a LISTEN state which would
break our assumptions about sockets always being ESTABLISHED state.

To resolve this rely on the unhash hook, which is called in the
disconnect case, to remove the sock from the sockmap.
Reported-by: NEric Dumazet <edumazet@google.com>
Fixes: 1aa12bdf ("bpf: sockmap, add sock close() hook to remove socks")
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NYonghong Song <yhs@fb.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

After this patch we only allow socks that are in ESTABLISHED state or
are being added via a sock_ops event that is transitioning into an
ESTABLISHED state. By allowing sock_ops events we allow users to
manage sockmaps directly from sock ops programs. The two supported
sock_ops ops are BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB and
BPF_SOCK_OPS_ACTIVE_ESTABLISHED_CB.

Similar to TLS ULP this ensures sk_user_data is correct.
Reported-by: NEric Dumazet <edumazet@google.com>
Fixes: 1aa12bdf ("bpf: sockmap, add sock close() hook to remove socks")
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NYonghong Song <yhs@fb.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

When extracting frames from the Ocelot switch, the frame check sequence
(FCS) is present at the end of the data extracted. The FCS was put into
the sk buffer which introduced some issues (as length related ones), as
the FCS shouldn't be part of an Rx sk buffer.

This patch fixes the Ocelot switch extraction behaviour by discarding
the FCS.

Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>