Commit bc69fdfc
("net: thunderx: Enable BGX LMAC's RX/TX only after VF is up")
introduces lmac_cnt member and starts verifying VF number against it.
This is plain wrong, and works only because currently we have hardcoded
1:1 mapping between VFs and LMACs, and in this case num_vf_en and
lmac_cnt are always equal. However in future this may change, and the
code will badly misbehave. The worst consequence of this is failure to
deliver link status messages, causing VFs to go defunct because since
commit 0b72a9a1 ("net: thunderx: Switchon carrier only upon
interface link up") VF will not fully bring itself up without it.

This patch fixes the potential problem by doing VF number checks against
the num_vf_en. Since lmac_cnt is not used anywhere else, it is removed.

Additionally some duplicated code is factored out into nic_enable_vf()
Signed-off-by: NPavel Fedin <p.fedin@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call to iptunnel_xmit_stats() is not required after udp-tunnel6-xmit.
By calling iptunnel_xmit_stats() results in incorrect device stats.
Following patch drops this call.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When looking for outer IP header, use the actual socket address family, not
the address family of the default destination which is not set for metadata
based interfaces (and doesn't have to match the address family of the
received packet even if it was set).

Fix also the misleading comment.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fill the metadata correctly even when tunneling over IPv6. Also, check that
the provided metadata is of an address family that is supported by the
tunnel.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Will be used also for ndo_fill_metadata_dst.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using INTa, ISR might be called before device is configured
for INTa [E.g., due to other device asserting the shared interrupt line],
in which case the ISR would read the SISR registers that shouldn't be
read unless HW is already configured for INTa. This might break interrupts
later on. There's also an MSI-X issue due to this difference, although
it's mostly theoretical.

This patch changes the initialization order, calling request_irq() for the
slowpath interrupt only after the chip is configured for working
in the preferred interrupt mode.
Signed-off-by: NSudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Can't rely on pci config space to discover bar size,
as in some environments this returns a wrong, too large value.
Instead, rely on device register, which contains the value
provided by MFW at preboot.
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Concurrent non-blocking slowpath ramrods can be completed
out-of-order on the completion chain. Recycling completed elements,
while previously sent elements are still completion pending,
can lead to overriding of active elements on the chain. Furthermore,
sending pending slowpath ramrods currently lacks the update of the
chain element physical pointer.

This patch:
* Ensures that ramrods are sent to the FW with
  consecutive echo values.
* Handles out-of-order completions by freeing only first
  successive completed entries.
* Updates the chain element physical pointer when copying
  a pending element into a free element for sending.
Signed-off-by: NTomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If NO_DMA=y:

    ERROR: "dma_map_single" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
    ERROR: "dma_unmap_page" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
    ERROR: "dma_sync_single_for_cpu" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
    ERROR: "dma_unmap_single" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
    ERROR: "dma_alloc_coherent" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
    ERROR: "dma_mapping_error" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
    ERROR: "dma_map_page" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
    ERROR: "dma_free_coherent" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of a tx queue timeout every transmit is blocked until the
QCA7000 resets himself and triggers a sync which makes the driver
flushs the tx ring. So avoid this blocking situation by triggering
the sync immediately after the timeout. Waking the queue doesn't
make sense in this situation.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06e ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Huawei E3372 (12d1:157d) needs this quirk in MBIM mode
as well. Allow this by forcing the NTB to contain only a
single NDP, and add a device specific entry for this ID.

Due to the way Huawei use device IDs, this might be applied
to other modems as well.  It is assumed that those modems
will be based on the same firmware and will need this quirk
too.  If not, it will still not harm normal usage, although
multiplexing performance could be impacted.

Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-by: NSami Farin <hvtaifwkbgefbaei@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Acked-By: NEnrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a memleak when suspend/resume this driver version.
Currently the stmmac, during resume step, reallocates all the resources
but they are not released when suspend.
The patch is not to release these resources but the logic has been changed.
In fact, it is not necessary to free and reallocate all from scratch
because the memory data will be always preserved.
As final solution, the patch just reinit the descriptors and the rx/tx
pointers only when resume. Tested done on STi boxes.
Reported-by: NZhengShunQian <zhengsq@rock-chips.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Rx queue #1 frame error counter name contains trailing underscore,
probably due to a typo...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a low memory situation the following kernel oops occurs:

Unable to handle kernel NULL pointer dereference at virtual address 00000050
pgd = 8490c000
[00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT ARM
Modules linked in:
CPU: 0    Not tainted  (3.4-at16 #9)
PC is at skb_put+0x10/0x98
LR is at sh_eth_poll+0x2c8/0xa10
pc : [<8035f780>]    lr : [<8028bf50>]    psr: 60000113
sp : 84eb1a90  ip : 84eb1ac8  fp : 84eb1ac4
r10: 0000003f  r9 : 000005ea  r8 : 00000000
r7 : 00000000  r6 : 940453b0  r5 : 00030000  r4 : 9381b180
r3 : 00000000  r2 : 00000000  r1 : 000005ea  r0 : 00000000
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c53c7d  Table: 4248c059  DAC: 00000015
Process klogd (pid: 2046, stack limit = 0x84eb02e8)
[...]

This is  because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left
NULL but sh_eth_rx() later  uses it without checking.  Add such check...
Reported-by: NYasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

atl1c driver is doing order-4 allocation with GFP_ATOMIC
priority. That often breaks  networking after resume. Switch to
GFP_KERNEL. Still not ideal, but should be significantly better.

atl1c_setup_ring_resources() is called from .open() function, and
already uses GFP_KERNEL, so this change is safe.
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NMichal Hocko <mhocko@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pppoe_connect() mustn't touch the padt_work field of pppoe sockets
because that work could be already pending.

[   21.473147] BUG: unable to handle kernel NULL pointer dereference at 00000004
[   21.474523] IP: [<c1043177>] process_one_work+0x29/0x31c
[   21.475164] *pde = 00000000
[   21.475513] Oops: 0000 [#1] SMP
[   21.475910] Modules linked in: pppoe pppox ppp_generic slhc crc32c_intel aesni_intel virtio_net xts aes_i586 lrw gf128mul ablk_helper cryptd evdev acpi_cpufreq processor serio_raw button ext4 crc16 mbcache jbd2 virtio_blk virtio_pci virtio_ring virtio
[   21.476168] CPU: 2 PID: 164 Comm: kworker/2:2 Not tainted 4.4.0-rc1 #1
[   21.476168] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014
[   21.476168] task: f5f83c00 ti: f5e28000 task.ti: f5e28000
[   21.476168] EIP: 0060:[<c1043177>] EFLAGS: 00010046 CPU: 2
[   21.476168] EIP is at process_one_work+0x29/0x31c
[   21.484082] EAX: 00000000 EBX: f678b2a0 ECX: 00000004 EDX: 00000000
[   21.484082] ESI: f6c69940 EDI: f5e29ef0 EBP: f5e29f0c ESP: f5e29edc
[   21.484082]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[   21.484082] CR0: 80050033 CR2: 000000a4 CR3: 317ad000 CR4: 00040690
[   21.484082] Stack:
[   21.484082]  00000000 f6c69950 00000000 f6c69940 c0042338 f5e29f0c c1327945 00000000
[   21.484082]  00000008 f678b2a0 f6c69940 f678b2b8 f5e29f30 c1043984 f5f83c00 f6c69970
[   21.484082]  f678b2a0 c10437d3 f6775e80 f678b2a0 c10437d3 f5e29fac c1047059 f5e29f74
[   21.484082] Call Trace:
[   21.484082]  [<c1327945>] ? _raw_spin_lock_irq+0x28/0x30
[   21.484082]  [<c1043984>] worker_thread+0x1b1/0x244
[   21.484082]  [<c10437d3>] ? rescuer_thread+0x229/0x229
[   21.484082]  [<c10437d3>] ? rescuer_thread+0x229/0x229
[   21.484082]  [<c1047059>] kthread+0x8f/0x94
[   21.484082]  [<c1327a32>] ? _raw_spin_unlock_irq+0x22/0x26
[   21.484082]  [<c1327ee9>] ret_from_kernel_thread+0x21/0x38
[   21.484082]  [<c1046fca>] ? kthread_parkme+0x19/0x19
[   21.496082] Code: 5d c3 55 89 e5 57 56 53 89 c3 83 ec 24 89 d0 89 55 e0 8d 7d e4 e8 6c d8 ff ff b9 04 00 00 00 89 45 d8 8b 43 24 89 45 dc 8b 45 d8 <8b> 40 04 8b 80 e0 00 00 00 c1 e8 05 24 01 88 45 d7 8b 45 e0 8d
[   21.496082] EIP: [<c1043177>] process_one_work+0x29/0x31c SS:ESP 0068:f5e29edc
[   21.496082] CR2: 0000000000000004
[   21.496082] ---[ end trace e362cc9cf10dae89 ]---
Reported-by: NAndrew <nitr0@seti.kr.ua>
Fixes: 287f3a94 ("pppoe: Use workqueue to die properly when a PADT is received")
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In hitherto code in case of RX buffer allocation error during refill,
original buffer is pushed to the network stack, but the amount of
available buffer pointers in BM pool is decreased.

This commit fixes the situation by moving refill call before skb_put(),
and returning original buffer pointer to the pool in case of an error.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375
network unit")

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each allocated buffer, whose pointer is put into BM pool is DMA-mapped.
Hence it should be properly unmapped after usage or when removing buffers
from pool.

This commit fixes DMA handling on RX path by adding dma_unmap_single() in
mvpp2_rx() and in mvpp2_bufs_free(). The latter function's argument number
had to be increased for this purpose.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375
network unit")

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This condition is true only for the last fragment of the packet.

Since every descriptor's buffer is DMA-mapped it has to be properly
unmapped.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375
network unit")

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the driver were to happen to have a mutex held while
the i40e_init_adminq call was called, the init_adminq might
inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantics.

Fix this by avoiding adminq.c code allocating/freeing this memory, and
then do the same work only once in probe/remove.

Testing Hints (Required if no HSD): for VF, load i40evf in bare metal
and echo 32 > sriov_numvfs; echo 0 > sriov_numvfs in a loop.  Yes this
is a horrible thing to do.

Change-ID: Ida263c51b34e195252179e7e5e400d73a99be7a2
Reported-by: NStefan Assmann <sassmann@redhat.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state.  Specifically the MAC address was
enabled for both VF 0 and the PF.  This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.

A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.

In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.

Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000

Result:
	MPSAR[0]               00000081
	MPSAR[254]             00000001

Expected Result, behavior after patch:
	MPSAR[0]               00000080
	MPSAR[254]             00000080
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: NJérôme Pouiller <jezz@sysmic.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters.  Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.

Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW.  For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.

v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: NJeffrey Huang <huangjw@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: NJeffrey Huang <huangjw@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs) and
by default it is set to 16, see arch/arm/include/asm/irq.h.

This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.

Fixes a runtime problem:

    lpc-eth 31060000.ethernet: error getting resources.
    lpc_eth: lpc-eth: not found (-6).
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since Armada 38x SoC can support IP checksum for jumbo frames only on
a single port, it means that this feature should be enabled per-port,
rather than for the whole SoC.

This patch enables setting custom TX IP checksum limit by adding new
optional property to the mvneta device tree node. If not used, by
default 1600B is set for "marvell,armada-370-neta" and 9800B for other
strings, which ensures backward compatibility. Binding documentation
is updated accordingly.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.

This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Acked-by: NSimon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # v4.2+
Fixes a84e3289 ("net: mvneta: fix refilling for Rx DMA buffers")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A value originally defined in the driver was inappropriate. Even though
the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK
to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16]
are reserved and read-only.

This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with
the controller's documentation.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>

Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer
allocation was mistakenly set as BIT(1). This commit fixes the assignment.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds missing configuration of MBUS windows access protection
in mvneta_conf_mbus_windows function - a dedicated variable for that
purpose remained there unused since v3.8 initial mvneta support. Because
of that the register contents were inherited from the bootloader.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable or disable BGX LMAC's RX/TX based on corresponding VF's
status. If otherwise, when multiple LMAC's physical link is up
then packets from all LMAC's whose corresponding VF is not yet
initialized will get forwarded to VF0. This is due to VNIC's default
configuration where CPI, RSSI e.t.c point to VF0/QSET0/RQ0.

This patch will prevent multiple copies of packets on VF0.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call netif_carrier_on() only if interface's link is up. Switching this on
upon IFF_UP by default, is causing issues with ethernet channel bonding
in LACP mode. Initial NETDEV_CHANGE notification was being skipped.

Also fixed some issues with link/speed/duplex reporting via ethtool.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Properly set CQ timer threshold and also set it to 2us.
With previous incorrect settings it was set to 0.5us which is too less.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While VNIC or BGX driver teardown, wait for already scheduled delayed work to
finish before destroying it.
Signed-off-by: NThanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NThanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Looks like 29fae1c8 ("HID: logitech: Add support for G29") was a little
bit aggressive and broke other devices.

Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=108121Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch is a cleanup to make following patch easier to
review.

Goal is to move SOCK_ASYNC_NOSPACE and SOCK_ASYNC_WAITDATA
from (struct socket)->flags to a (struct socket_wq)->flags
to benefit from RCU protection in sock_wake_async()

To ease backports, we rename both constants.

Two new helpers, sk_set_bit(int nr, struct sock *sk)
and sk_clear_bit(int net, struct sock *sk) are added so that
following patch can change their implementation.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent patches added basic support for the Apple NVMe controller but
still cause resets and data corruption on that particular controller
when a specific pattern of read/flush commands occurs. Limiting the
queue depth to 2 works around that issue.

This patch enforces that limit only for the Apple controller and is
considered a temporary fix until we find the root source of that
problem.
Signed-off-by: NStephan Günther <guenther@tum.de>
Signed-off-by: NMaurice Leclaire <leclaire@in.tum.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

vmxnet3_drv does not check dma_addr with dma_mapping_error()
after mapping dma memory. The patch adds the checks and
tries to handle failures.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: NShrikrishna Khare <skhare@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>