Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 22 3月, 2006 2 次提交
  3. 15 3月, 2006 1 次提交
  5. 10 3月, 2006 1 次提交
  7. 09 3月, 2006 2 次提交
    • A
      [PATCH] i386: port ATI timer fix from x86_64 to i386 II · f9262c12
      由 Andi Kleen 提交于 
      ATI chipsets tend to generate double timer interrupts for the local APIC
timer when both the 8254 and the IO-APIC timer pins are enabled.  This is
because they route it to both and the result is anded together and the CPU
ends up processing it twice.

This patch changes check_timer to disable the 8254 routing for interrupt 0.

I think it would be safe on all chipsets actually (i tested it on a couple
and it worked everywhere) and Windows seems to do it in a similar way, but
to be conservative this patch only enables this mode on ATI (and adds
options to enable/disable too)

Ported over from a similar x86-64 change.

I reused the ACPI earlyquirk infrastructure for the ATI bridge check, but
tweaked it a bit to work even without ACPI.

Inspired by a patch from Chuck Ebbert, but redone.

Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      f9262c12
    • D
      [PATCH] rcu batch tuning · 21a1ea9e
      由 Dipankar Sarma 提交于 
      This patch adds new tunables for RCU queue and finished batches.  There are
two types of controls - number of completed RCU updates invoked in a batch
(blimit) and monitoring for high rate of incoming RCUs on a cpu (qhimark,
qlowmark).

By default, the per-cpu batch limit is set to a small value.  If the input
RCU rate exceeds the high watermark, we do two things - force quiescent
state on all cpus and set the batch limit of the CPU to INTMAX.  Setting
batch limit to INTMAX forces all finished RCUs to be processed in one shot.
 If we have more than INTMAX RCUs queued up, then we have bigger problems
anyway.  Once the incoming queued RCUs fall below the low watermark, the
batch limit is set to the default.
Signed-off-by: NDipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      21a1ea9e
  9. 08 3月, 2006 3 次提交
  11. 04 3月, 2006 3 次提交
  13. 03 3月, 2006 3 次提交
  15. 28 2月, 2006 1 次提交
  17. 27 2月, 2006 9 次提交
  19. 25 2月, 2006 1 次提交
  21. 24 2月, 2006 1 次提交
  23. 23 2月, 2006 1 次提交
    • G
      Revert mount/umount uevent removal · fa675765
      由 Greg Kroah-Hartman 提交于 
      This change reverts the 033b96fd commit
from Kay Sievers that removed the mount/umount uevents from the kernel.
Some older versions of HAL still depend on these events to detect when a
new device has been mounted.  These events are not correctly emitted,
and are broken by design, and so, should not be relied upon by any
future program.  Instead, the /proc/mounts file should be polled to
properly detect this kind of event.

A feature-removal-schedule.txt entry has been added, noting when this
interface will be removed from the kernel.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      fa675765
  25. 22 2月, 2006 1 次提交
    • H
      [PATCH] tmpfs: fix mount mpol nodelist parsing · b00dc3ad
      由 Hugh Dickins 提交于 
      I've been dissatisfied with the mpol_nodelist mount option which was
added to tmpfs earlier in -rc.  Replace it by mpol=policy:nodelist.

And it was broken: a nodelist is a comma-separated list of numbers and
ranges; the mount options are a comma-separated list of token=values.
Whoops, blindly strsep'ing on commas doesn't work so well: since we've
no numeric tokens, and unlikely to add them, use that to distinguish.

Move the mpol= parsing to shmem_parse_mpol under CONFIG_NUMA, reject
all its options as invalid if not NUMA.  /proc shows MPOL_PREFERRED
as "prefer", so use that name for the policy instead of "preferred".

Enforce that mpol=default has no nodelist; that mpol=prefer has one
node only; that mpol=bind has a nodelist; but let mpol=interleave use
node_online_map if no nodelist given.  Describe this in tmpfs.txt.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Acked-by: NRobin Holt <holt@sgi.com>
Acked-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      b00dc3ad
  27. 21 2月, 2006 3 次提交
  29. 18 2月, 2006 3 次提交
  31. 17 2月, 2006 1 次提交
  33. 16 2月, 2006 1 次提交
  35. 15 2月, 2006 3 次提交
    • D
      [PATCH] FRV: Use virtual interrupt disablement · 28baebae
      由 David Howells 提交于 
      Make the FRV arch use virtual interrupt disablement because accesses to the
processor status register (PSR) are relatively slow and because we will
soon have the need to deal with multiple interrupt controls at the same
time (separate h/w and inter-core interrupts).

The way this is done is to dedicate one of the four integer condition code
registers (ICC2) to maintaining a virtual interrupt disablement state
whilst inside the kernel.  This uses the ICC2.Z flag (Zero) to indicate
whether the interrupts are virtually disabled and the ICC2.C flag (Carry)
to indicate whether the interrupts are physically disabled.

ICC2.Z is set to indicate interrupts are virtually disabled.  ICC2.C is set
to indicate interrupts are physically enabled.  Under normal running
conditions Z==0 and C==1.

Disabling interrupts with local_irq_disable() doesn't then actually
physically disable interrupts - it merely sets ICC2.Z to 1.  Should an
interrupt then happen, the exception prologue will note ICC2.Z is set and
branch out of line using one instruction (an unlikely BEQ).  Here it will
physically disable interrupts and clear ICC2.C.

When it comes time to enable interrupts (local_irq_enable()), this simply
clears the ICC2.Z flag and invokes a trap #2 if both Z and C flags are
clear (the HI integer condition).  This can be done with the TIHI
conditional trap instruction.

The trap then physically reenables interrupts and sets ICC2.C again.  Upon
returning the interrupt will be taken as interrupts will then be enabled.
Note that whilst processing the trap, the whole exceptions system is
disabled, and so an interrupt can't happen till it returns.

If no pending interrupt had happened, ICC2.C would still be set, the HI
condition would not be fulfilled, and no trap will happen.

Saving interrupts (local_irq_save) is simply a matter of pulling the ICC2.Z
flag out of the CCR register, shifting it down and masking it off.  This
gives a result of 0 if interrupts were enabled and 1 if they weren't.

Restoring interrupts (local_irq_restore) is then a matter of taking the
saved value mentioned previously and XOR'ing it against 1.  If it was one,
the result will be zero, and if it was zero the result will be non-zero.
This result is then used to affect the ICC2.Z flag directly (it is a
condition code flag after all).  An XOR instruction does not affect the
Carry flag, and so that bit of state is unchanged.  The two flags can then
be sampled to see if they're both zero using the trap (TIHI) as for the
unconditional reenablement (local_irq_enable).

This patch also:

 (1) Modifies the debugging stub (break.S) to handle single-stepping crossing
     into the trap #2 handler and into virtually disabled interrupts.

 (2) Removes superseded fixup pointers from the second instructions in the trap
     tables (there's no a separate fixup table for this).

 (3) Declares the trap #3 vector for use in .org directives in the trap table.

 (4) Moves irq_enter() and irq_exit() in do_IRQ() to avoid problems with
     virtual interrupt handling, and removes the duplicate code that has now
     been folded into irq_exit() (softirq and preemption handling).

 (5) Tells the compiler in the arch Makefile that ICC2 is now reserved.

 (6) Documents the in-kernel ABI, including the virtual interrupts.

 (7) Renames the old irq management functions to different names.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      28baebae
    • J
      [PATCH] kprobes: Update Documentation/kprobes.txt · 8861da31
      由 Jim Keniston 提交于 
      Update Documentation/kprobes.txt to reflect Kprobes enhancements and other
recent developments.
Acked-by: NAnanth Mavinakayanahalli <mananth@in.ibm.com>
Signed-off-by: NJim Keniston <jkenisto@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      8861da31
    • R
      [MIPS] Update docs to reflect the latest status of the Alchemy IDE driver. · a3c9dc38
      由 Ralf Baechle 提交于 
      Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      a3c9dc38