Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 18 2月, 2019 1 次提交
  3. 25 1月, 2019 1 次提交
    • Z
      net: usb: asix: ax88772_bind return error when hw_reset fail · 6eea3527
      由 Zhang Run 提交于 
      The ax88772_bind() should return error code immediately when the PHY
was not reset properly through ax88772a_hw_reset().
Otherwise, The asix_get_phyid() will block when get the PHY
Identifier from the PHYSID1 MII registers through asix_mdio_read()
due to the PHY isn't ready. Furthermore, it will produce a lot of
error message cause system crash.As follows:
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to send
 software reset: ffffffb9
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
 software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
 software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
 reg index 0x0000: -71
...
Signed-off-by: NZhang Run <zhang.run@zte.com.cn>
Reviewed-by: NYang Wei <yang.wei9@zte.com.cn>
Tested-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6eea3527
  5. 17 1月, 2019 1 次提交
  7. 08 1月, 2019 1 次提交
  9. 05 1月, 2019 1 次提交
  11. 22 12月, 2018 2 次提交
  13. 19 12月, 2018 1 次提交
    • J
      lan78xx: Resolve issue with changing MAC address · 15515aaa
      由 Jason Martinsen 提交于 
      Current state for the lan78xx driver does not allow for changing the
MAC address of the interface, without either removing the module (if
you compiled it that way) or rebooting the machine.  If you attempt to
change the MAC address, ifconfig will show the new address, however,
the system/interface will not respond to any traffic using that
configuration.  A few short-term options to work around this are to
unload the module and reload it with the new MAC address, change the
interface to "promisc", or reboot with the correct configuration to
change the MAC.

This patch enables the ability to change the MAC address via fairly normal means...
ifdown <interface>
modify entry in /etc/network/interfaces OR a similar method
ifup <interface>
Then test via any network communication, such as ICMP requests to gateway.

My only test platform for this patch has been a raspberry pi model 3b+.
Signed-off-by: NJason Martinsen <jasonmartinsen@msn.com>

-----
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      15515aaa
  15. 16 12月, 2018 2 次提交
  17. 15 12月, 2018 1 次提交
  19. 13 12月, 2018 1 次提交
  21. 01 12月, 2018 1 次提交
  23. 30 11月, 2018 1 次提交
  25. 28 11月, 2018 22 次提交
  27. 17 11月, 2018 4 次提交