Switch to the updated coresight bindings.

Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NSuzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Pass the 'no-sd' for esdhc0 controller as it is wired to eMMC.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Acked-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

No SDIO devices are connected to these ports, so pass the 'no-sdio'
property.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Acked-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

imx51-zii-scu2-mezz has an external watchdog in the environment
microcontroller, so disable the internal one.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Acked-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

imx51-zii-scu2-mezz does not have any video encoding/decoding needs,
so disable the VPU.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Acked-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

imx51-zii-scu3-esb does not have any video encoding/decoding needs,
so disable the VPU.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Acked-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add label for VPU node so that board dts files can disable VPU
if needed.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Acked-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Update VDD_SOC voltage to 1.25V for 900MHz operating point
according to datasheet Rev. 1.3, 08/2018, 25mV is added to
the minimum allowed values to cover power supply ripple.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Reviewed-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The ConnectCore 6UL Single Board Computer (SBC) Pro contains the
ConnectCore 6UL System-On-Module.

Its hardware specifications are:

* 256MB DDR3 memory
* On module 256MB NAND flash
* Dual 10/100 Ethernet
* USB Host and USB OTG
* Parallel RGB display header
* LVDS display header
* CSI camera
* GPIO header
* I2C, SPI, CAN headers
* PCIe mini card and micro SIM slot
* MicroSD external storage
* On board 4GB eMMC flash
* Audio headphone, line in/out, microphone lines
Signed-off-by: NAlex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This board, as well as some other boards with i.MX6 and a PMIC, uses a
"PMIC_STBY_REQ" line to notify the PMIC about a state change.
The PMIC is programmed for a specific state change before triggering the
line.
In this case, PMIC_STBY_REQ can be used for stand by, sleep
and power off modes.
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The pinctrl properties on the IOMUXC node get overwritten by the
carrier board level device tree, hence the pinctrl_reset_moci
pinctrl does not get applied.

Associate the pinctrl_reset_moci pinctrl with the PCIe node where
we also make use of the pin as a reset GPIO.

Since the pin is muxed as a GPIO by default not muxing it explicitly
worked fine in practise.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

There is no need to keep the PMU disabled.

Enable it like it is done in the other i.MX dtsi files.

With this change applied we see:

[    1.338866] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add egalax touch screen support on i2c2 bus.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add i.MX6QDL SabreAuto board's gpio keys support, there
are 5 gpio keys on base board:

SW3: KEY_HOME;
SW4: KEY_BACK;
SW5: KEY_PROGRAM;
SW6: KEY_VOLUMEUP;
SW7: KEY_VOLUMEDOWN;
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The board typically has 2 populated SFF interfaces. The mv88e6xxx
driver currently supports SFF modules connected to ports 9 and 10 of
the mv88e6390. Add support for sff2, which is connected to port 9.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The switch has an SFF attached to port 5. Add the SFF device, the
pinmux for its GPIOs, and list the port in the switch configuration.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Update i.MX6ULL iomux header according to latest reference
manual Rev.1, 11/2017.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Reviewed-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable cpuidle for i.MX7S/D using generic ARM cpuidle
driver, below 2 idle states enabled:

1. ARM WFI;
2. SoC WAIT mode.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch enables i.MX6SX SDB board's below GPIO buttons
as wakeup sources:

SW4(FUNC1): KEY_VOLUMEUP
SW5(FUNC2): KEY_VOLUMEDOWN
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch enables i.MX7D SDB board's below GPIO buttons
as wakeup sources:

S1(FUNC1): KEY_VOLUMEUP
S3(FUNC2): KEY_VOLUMEDOWN
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease
license compliance management.
Signed-off-by: NPierre-Jean Texier <texier.pj2@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

NOR and IFC controller connectivity is big-endian.
So add big-endian field in nor device tree node allowing
IFC controller to read/write data from/to the flash correctly.
Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Acked-by: NLi Yang <leoyang.li@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

i.MX6ULL is a lite version of i.MX6UL, its full name
is i.MX6 UltraLiteLite, NOT UlltraLite.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

i.MX6SLL has GPIO clock gates in CCM CCGR, add
clock property for GPIO driver to make sure all
GPIO banks work as expected.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add weim node for i.MX6UL SOC.
Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signals available on both i.MX6UL and i.MX6ULL should have the same name
because it is the case of all others common signals, it avoids to make
mistakes (use the wrong ones) and it makes writing device tree files
less complicated. For example:

imx6ul-imx6ull-board.dtsi:
 ...
 pinctrl_uart5: uart5grp {
	fsl,pins = <
		MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX   0x1b0b1
	 	MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX   0x1b0b1
 	 >;
 };

imx6ul-board.dts:
 #include <imx6ul.dtsi>
 #include <imx6ul-imx6ull-board.dtsi>
 ...

imx6ull-board.dts:
 #include <imx6ull.dtsi>
 #include <imx6ul-imx6ull-board.dtsi>
 ...

Without this patch, the imx6ull-board.dtb will use
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX instead of
MX6ULL_PAD_UART5_RX_DATA__UART5_DCE_RX and the uart5 will be
misconfigured.
Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Setting a stdout-path in the .dtb is convenient because then the user
gets a serial console on the RS-232 connector without any extra effort
of figuring out the relevant 'console=' boot parameter.
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The WaRP7 has one mikroBUS socket on the back to plug click boards.
This patch allows to interact with some of these
i2c modules (EEPROM, RTC and so on).
Signed-off-by: NPierre-Jean Texier <texier.pj2@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The "EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation" is based on the 1.5 version
of the i.Core MX6 cpu module. The 1.5 version differs from the original one for
a few details, including the ethernet PHY interface clock provider.

With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver

While before using the 1.5 version, ethernet failed to startup do to un-clocked
PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY

Fixes: 3fe08835 ("ARM: dts: imx6q: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NJacopo Mondi <jacopo@jmondi.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The 1.5 version of Engicam's i.Core MX6 CPU module features a different clock
provider for the ethernet's PHY interface. Adjust the FEC ptp clock to
reference CLK_ENET_REF clock source, and set SION bit of
MX6QDL_PAD_GPIO_16__ENET_REF_CLK to adjust the input path of that pin.

The newly introduced imx6ql-icore-1.5.dtsi allows to collect in a single
place differences between version '1.0' and '1.5' of the module.
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NJacopo Mondi <jacopo@jmondi.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Gives substantial performance improvement for transfers larger than 16
bytes (DMA_THRESHOLD).  Smaller transfers are unaffected.
Signed-off-by: NEsben Haabendal <eha@deif.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Use consistent pinctrl node names for Engicam dt files,
sufix 'grp' look consistent than actual node name

- pinctrl_gpmi_nand: gpmi-nand {
+ pinctrl_gpmi_nand: gpminandgrp {
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Move usdhc2 and gpmi along with pinctrl nodes on
imx6ul-isiot.dtsi from dts files and mark it as 'disabled'
and the relevant dts will enable the status as 'okay'
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.

Also added Engicam Copyright on missing files.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

System poweroff is already supported by PSCI on i.MX7D,
remove "snvs_poweroff" node to avoid below debug message
from syscon-poweroff driver:

[    1.831414] syscon-poweroff 30370000.snvs:snvs-poweroff: pm_power_off already claimed (ptrval) psci_sys_poweroff
[    1.841707] syscon-poweroff: probe of 30370000.snvs:snvs-poweroff failed with error -16
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Define the Messaging Unit (MU) for i.MX7 in the processor's dtsi.
The respective driver is added in the next commit.
Reviewed-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The i.MX7ULP B0 chip has some pin changes for USB and VIU
module, update pinfunc header file accordingly.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The MC13892 Analog-to-Digital input pins (ADIN5-7) are exposed on the
imx51-babbage board.

Pass the "fsl,mc13xxx-uses-adc" property so that the MC13892 ADC
block can work.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX6SLL pinctrl driver, for details, please refer to
Documentation/devicetree/bindings/gpio/gpio.txt of "gpio-ranges"
property.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This updates the ARM Versatile defconfig to the latest
Kconfig structural changes and adds the DUMB VGA bridge
driver so that VGA works out of the box, e.g. with QEMU.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>