Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.

Change the trivial cases.

v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
  - Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: NPradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The energy detect enable/disable code in the driver uses some
register defines in this header unconditionally, so guarding
the smscphy.h header include with CONFIG_SMSC_PHY leads to
build failures in some configurations.
Reported-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMSC LAN generation 4 chips integrate an IEEE 802.3 ethernet physical layer.
The PHY driver for this integrated chip enable an energy detect power-down mode.
When the PHY is in a power-down mode, it prevents the MAC portion chip to be
software reseted.

That means that if we compile the kernel with the configuration option SMSC_PHY
enabled and try to bring the network interface up without an cable plug-ed the
PHY will be in a low power mode and the software reset will fail returning -EIO
to user-space:

root@igep00x0:~# ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error

This patch disable the energy detect power-down mode before trying to software
reset the LAN chip and re-enables after it was reseted successfully.
Signed-off-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMSC generation 4 LAN chips integrate an IEEE 802.3 ethernet physical layer.
The ethernet driver for this family of devices needs to access the SMSC PHY
registers and bit-fields.

So, this patch moves these constants to a place where it can be used for both
the PHY and LAN drivers.
Signed-off-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some basic regulator support for the power pins, as needed
by the ST-Ericsson Snowball platform that powers up the SMSC911
chip using an external regulator.

Platforms that use regulators and the smsc911x and have no defined
regulator for the smsc911x and claim complete regulator
constraints with no dummy regulators will need to provide it, for
example using a fixed voltage regulator. It appears that this may
affect (apart from Ux500 Snowball) possibly these archs/machines
that from some grep:s appear to define both CONFIG_SMSC911X and
CONFIG_REGULATOR:

- ARM Freescale mx3 and OMAP 2 plus, Raumfeld machines
- Blackfin
- Super-H

Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRobert Marklund <robert.marklund@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the drivers in drivers/net/ethernet/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert some remaining straglers' .get_drvinfo routines to use strlcpy
rather than strcpy/strncpy.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wait for the chip to be ready before any access to it. On the
Snowball platform we need to enable an external regulator before
the chip comes online, and then it happens that the device is
not yet ready at probe time, so let's wait for it.
Signed-off-by: NRobert Marklund <robert.marklund@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device.h header was including module.h, making it present for
most of these drivers.  But we want to clean that up.  Call out the
include of module.h in the modular network drivers.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

The SMSC911X_USE_16BIT needs to be set when using 16-bit register
access.  However, currently no flag is set if the device tree
doesn't specify 32-bit access, resulting in a BUG() and a non-
working driver when 16-bit register access is configured for
smsc911x in the DT.

This patch should set the SMSC911X_USE_16BIT flag in a manner
consistent with the documented DT bindings.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well.  It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled.  This caused a dependency error.

Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.

This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers.  In
addition, by enabling all the new Kconfig options does not add
any un-expected options.

CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the SMC (SMSC) drivers into drivers/net/ethernet/smsc/ and the
necessary Kconfig and Makefile changes.  Also did some cleanup
of NET_VENDOR_SMC Kconfig tag for the 8390 based drivers.

CC: Nicolas Pitre <nico@fluxnic.net>
CC: Donald Becker <becker@scyld.com>
CC: Erik Stahlman <erik@vt.edu>
CC: Dustin McIntire <dustin@sensoria.com>
CC: Steve Glendinning <steve.glendinning@smsc.com>
CC: David Hinds <dahinds@users.sourceforge.net>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>