Commit 954a03be ("iommu/arm-smmu: Break insecure users by disabling
bypass by default") intentionally breaks all devices using the SMMU in
bypass mode. This breaks, among other things, PCI support on Tegra186.
Fix this by populating the iommus property and friends for the PCIe
controller.

Fixes: 954a03be ("iommu/arm-smmu: Break insecure users by disabling bypass by default")
Signed-off-by: NThierry Reding <treding@nvidia.com>

Commit 954a03be ("iommu/arm-smmu: Break insecure users by disabling
bypass by default") intentionally breaks all devices using the SMMU in
bypass mode. This is breaking various devices on Tegra186 which include
the ethernet, BPMP and HDA device. Fix this by populating the iommus
property for these devices with their stream ID.

Fixes: 954a03be ("iommu/arm-smmu: Break insecure users by disabling bypass by default")
Signed-off-by: NJonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Various regulators were marked as always-on for Jetson TX2. At this
point, all of the regulators are properly hooked up, so this workaround
is no longer required.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Enable the relevant pads for XUSB support on P2771-0000 and hook up the
USB supply voltage regulators to the ports.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Adds the XUSB pad and XUSB controllers on Tegra186.
Reviewed-by: NJC Kuo <jckuo@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The Jetson Nano Developer Kit is a Tegra X1 based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4 GB
of LPDDR4, an SPI NOR flash for early boot firmware and an SD card slot
used for storage.

HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. An M.2 Key-E
slot with PCIe x1 adds additional possibilities.

A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The XUSB pad controller is responsible for supplying power to the PLLs
used to drive the various USB, PCI and SATA pads. Move the PLL power
supplies from the PCIe and XUSB controllers to the XUSB pad controller
to make sure they are available when needed.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The XUSB pad controller is responsible for supplying power to the PLLs
used to drive the various USB, PCI and SATA pads. Move the PLL power
supplies from the PCIe and XUSB controllers to the XUSB pad controller
to make sure they are available when needed.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The workaround for a hardware bug preventing this from working has been
merged now, so command queue support can be enabled again for Tegra186.
Tested-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Default tap and trim values are incorrect for Tegra186 SDMMC4. This
patch fixes them.
Tested-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The VCC supply property is not populated for the temperature sensor on
the P2888 board and so the following warning is observed on boot ...

 lm90 0-004c: 0-004c supply vcc not found, using dummy regulator

On the P2888 board, the VCC supply for the temperature sensor is
connected to the 'vdd_1v8ls' rail. Add the 'vcc-supply' property for
the temperature sensor to prevent this warning message from occurring.

Fixes: 8b457812 ('arm64: tegra: Add temperature sensor on P2888')
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

These are currently mostly unused because we lack a proper audio driver
on Tegra210. However, enabling them makes sure that at least their probe
code paths are tested at runtime.
Signed-off-by: NSameer Pujar <spujar@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add L2 cache and make it the next level of cache for each of the CPUs.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Enable CPU idle support for Shield platform.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Enable CPU idle support for Smaug platform.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Enable CPU idle support for Jetson TX1 platform.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add idle states properties for generic ARM CPU idle driver. This
includes a cpu-sleep state which is the power down state of CPU cores.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Acked-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Fix timer node to make it work with Tegra210 timer driver.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Pull KVM fixes from Paolo Bonzini:
 "A collection of x86 and ARM bugfixes, and some improvements to
  documentation.

  On top of this, a cleanup of kvm_para.h headers, which were exported
  by some architectures even though they not support KVM at all. This is
  responsible for all the Kbuild changes in the diffstat"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
  Documentation: kvm: clarify KVM_SET_USER_MEMORY_REGION
  KVM: doc: Document the life cycle of a VM and its resources
  KVM: selftests: complete IO before migrating guest state
  KVM: selftests: disable stack protector for all KVM tests
  KVM: selftests: explicitly disable PIE for tests
  KVM: selftests: assert on exit reason in CR4/cpuid sync test
  KVM: x86: update %rip after emulating IO
  x86/kvm/hyper-v: avoid spurious pending stimer on vCPU init
  kvm/x86: Move MSR_IA32_ARCH_CAPABILITIES to array emulated_msrs
  KVM: x86: Emulate MSR_IA32_ARCH_CAPABILITIES on AMD hosts
  kvm: don't redefine flags as something else
  kvm: mmu: Used range based flushing in slot_handle_level_range
  KVM: export <linux/kvm_para.h> and <asm/kvm_para.h> iif KVM is supported
  KVM: x86: remove check on nr_mmu_pages in kvm_arch_commit_memory_region()
  kvm: nVMX: Add a vmentry check for HOST_SYSENTER_ESP and HOST_SYSENTER_EIP fields
  KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)
  KVM: Reject device ioctls from processes other than the VM's creator
  KVM: doc: Fix incorrect word ordering regarding supported use of APIs
  KVM: x86: fix handling of role.cr4_pae and rename it to 'gpte_size'
  KVM: nVMX: Do not inherit quadrant and invalid for the root shadow EPT
  ...

Pull x86 fixes from Thomas Gleixner:
 "A pile of x86 updates:

   - Prevent exceeding he valid physical address space in the /dev/mem
     limit checks.

   - Move all header content inside the header guard to prevent compile
     failures.

   - Fix the bogus __percpu annotation in this_cpu_has() which makes
     sparse very noisy.

   - Disable switch jump tables completely when retpolines are enabled.

   - Prevent leaking the trampoline address"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/realmode: Make set_real_mode_mem() static inline
  x86/cpufeature: Fix __percpu annotation in this_cpu_has()
  x86/mm: Don't exceed the valid physical address space
  x86/retpolines: Disable switch jump tables when retpolines are enabled
  x86/realmode: Don't leak the trampoline kernel address
  x86/boot: Fix incorrect ifdeffery scope
  x86/resctrl: Remove unused variable

Pull perf tooling fixes from Thomas Gleixner:
 "Core libraries:
   - Fix max perf_event_attr.precise_ip detection.
   - Fix parser error for uncore event alias
   - Fixup ordering of kernel maps after obtaining the main kernel map
     address.

  Intel PT:
   - Fix TSC slip where A TSC packet can slip past MTC packets so that
     the timestamp appears to go backwards.
   - Fixes for exported-sql-viewer GUI conversion to python3.

  ARM coresight:
   - Fix the build by adding a missing case value for enumeration value
     introduced in newer library, that now is the required one.

  tool headers:
   - Syncronize kernel headers with the kernel, getting new io_uring and
     pidfd_send_signal syscalls so that 'perf trace' can handle them"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf pmu: Fix parser error for uncore event alias
  perf scripts python: exported-sql-viewer.py: Fix python3 support
  perf scripts python: exported-sql-viewer.py: Fix never-ending loop
  perf machine: Update kernel map address and re-order properly
  tools headers uapi: Sync powerpc's asm/kvm.h copy with the kernel sources
  tools headers: Update x86's syscall_64.tbl and uapi/asm-generic/unistd
  tools headers uapi: Update drm/i915_drm.h
  tools arch x86: Sync asm/cpufeatures.h with the kernel sources
  tools headers uapi: Sync linux/fcntl.h to get the F_SEAL_FUTURE_WRITE addition
  tools headers uapi: Sync asm-generic/mman-common.h and linux/mman.h
  perf evsel: Fix max perf_event_attr.precise_ip detection
  perf intel-pt: Fix TSC slip
  perf cs-etm: Add missing case value

Pull CPU hotplug fixes from Thomas Gleixner:
 "Two SMT/hotplug related fixes:

   - Prevent crash when HOTPLUG_CPU is disabled and the CPU bringup
     aborts. This is triggered with the 'nosmt' command line option, but
     can happen by any abort condition. As the real unplug code is not
     compiled in, prevent the fail by keeping the CPU in zombie state.

   - Enforce HOTPLUG_CPU for SMP on x86 to avoid the above situation
     completely. With 'nosmt' being a popular option it's required to
     unplug the half brought up sibling CPUs (due to the MCE wreckage)
     completely"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smp: Enforce CONFIG_HOTPLUG_CPU when SMP=y
  cpu/hotplug: Prevent crash when CPU bringup fails on CONFIG_HOTPLUG_CPU=n

Pull locking fixlet from Thomas Gleixner:
 "Trivial update to the maintainers file"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  MAINTAINERS: Remove deleted file from futex file pattern

Pull core fixes from Thomas Gleixner:
 "A small set of core updates:

   - Make the watchdog respect the selected CPU mask again. That was
     broken by the rework of the watchdog thread management and caused
     inconsistent state and NMI watchdog being unstoppable.

   - Ensure that the objtool build can find the libelf location.

   - Remove dead kcore stub code"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  watchdog: Respect watchdog cpumask on CPU hotplug
  objtool: Query pkg-config for libelf location
  proc/kcore: Remove unused kclist_add_remap()

Pull powerpc fixes from Michael Ellerman:
 "Three non-regression fixes.

   - Our optimised memcmp could read past the end of one of the buffers
     and potentially trigger a page fault leading to an oops.

   - Some of our code to read energy management data on PowerVM had an
     endian bug leading to bogus results.

   - When reporting a machine check exception we incorrectly reported
     TLB multihits as D-Cache multhits due to a missing entry in the
     array of causes.

  Thanks to: Chandan Rajendra, Gautham R. Shenoy, Mahesh Salgaonkar,
  Segher Boessenkool, Vaidyanathan Srinivasan"

* tag 'powerpc-5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries/mce: Fix misleading print for TLB mutlihit
  powerpc/pseries/energy: Use OF accessor functions to read ibm,drc-indexes
  powerpc/64: Fix memcmp reading past the end of src/dest

Pull dmaengine fixes from Vinod Koul:

 - Revert "dmaengine: stm32-mdma: Add a check on read_u32_array" as that
   caused regression

 - Fix MAINTAINER file uniphier-mdmac.c file path

* tag 'dmaengine-fix-5.1-rc3' of git://git.infradead.org/users/vkoul/slave-dma:
  MAINTAINERS: Fix uniphier-mdmac.c file path
  dmaengine: stm32-mdma: Revert "dmaengine: stm32-mdma: Add a check on read_u32_array"

Merge tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED fixes from Jacek Anaszewski:

 - fix refcnt leak on interface rename

 - use memcpy in device_name_store() to avoid including garbage from a
   previous, longer value in the device_name

 - fix a potential NULL pointer dereference in case of_match_device()
   cannot find a match

* tag 'led-fixes-for-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: trigger: netdev: use memcpy in device_name_store
  leds: pca9532: fix a potential NULL pointer dereference
  leds: trigger: netdev: fix refcnt leak on interface rename

Pull GPIO fixes from Linus Walleij:
 "As you can see [in the git history] I was away on leave and Bartosz
  kindly stepped in and collected a slew of fixes, I pulled them into my
  tree in two sets and merged some two more fixes (fixing my own caused
  bugs) on top.

  Summary:

   - Revert the extended use of gpio_set_config() and think about how we
     can do this properly.

   - Fix up the SPI CS GPIO handling so it now works properly on the SPI
     bus children, as intended.

   - Error paths and driver fixes"

* tag 'gpio-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: mockup: use simple_read_from_buffer() in debugfs read callback
  gpio: of: Fix of_gpiochip_add() error path
  gpio: of: Check for "spi-cs-high" in child instead of parent node
  gpio: of: Check propname before applying "cs-gpios" quirks
  gpio: mockup: fix debugfs read
  Revert "gpio: use new gpio_set_config() helper in more places"
  gpio: aspeed: fix a potential NULL pointer dereference
  gpio: amd-fch: Fix bogus SPDX identifier
  gpio: adnp: Fix testing wrong value in adnp_gpio_direction_input
  gpio: exar: add a check for the return value of ida_simple_get fails

If userspace doesn't end the input with a newline (which can easily
happen if the write happens from a C program that does write(fd,
iface, strlen(iface))), we may end up including garbage from a
previous, longer value in the device_name. For example

# cat device_name

# printf 'eth12' > device_name
# cat device_name
eth12
# printf 'eth3' > device_name
# cat device_name
eth32

I highly doubt anybody is relying on this behaviour, so switch to
simply copying the bytes (we've already checked that size is <
IFNAMSIZ) and unconditionally zero-terminate it; of course, we also
still have to strip a trailing newline.

This is also preparation for future patches.

Fixes: 06f502f5 ("leds: trigger: Introduce a NETDEV trigger")
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJacek Anaszewski <jacek.anaszewski@gmail.com>

In case of_match_device cannot find a match, return -EINVAL to avoid
NULL pointer dereference.

Fixes: fa4191a6 ("leds: pca9532: Add device tree support")
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Signed-off-by: NJacek Anaszewski <jacek.anaszewski@gmail.com>

Pull staging driver fixes from Greg KH:
 "Here are some small staging driver fixes for 5.1-rc3, and one driver
  removal.

  The biggest thing here is the removal of the mt7621-eth driver as a
  "real" network driver was merged in 5.1-rc1 for this hardware, so this
  old driver can now be removed.

  Other than that, there are just a number of small fixes, all resolving
  reported issues and some potential corner cases for error handling
  paths.

  All of these have been in linux-next with no reported issues"

* tag 'staging-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: vt6655: Remove vif check from vnt_interrupt
  staging: erofs: keep corrupted fs from crashing kernel in erofs_readdir()
  staging: octeon-ethernet: fix incorrect PHY mode
  staging: vc04_services: Fix an error code in vchiq_probe()
  staging: erofs: fix error handling when failed to read compresssed data
  staging: vt6655: Fix interrupt race condition on device start up.
  staging: rtlwifi: Fix potential NULL pointer dereference of kzalloc
  staging: rtl8712: uninitialized memory in read_bbreg_hdl()
  staging: rtlwifi: rtl8822b: fix to avoid potential NULL pointer dereference
  staging: rtl8188eu: Fix potential NULL pointer dereference of kcalloc
  staging, mt7621-pci: fix build without pci support
  staging: speakup_soft: Fix alternate speech with other synths
  staging: axis-fifo: add CONFIG_OF dependency
  staging: olpc_dcon_xo_1: add missing 'const' qualifier
  staging: comedi: ni_mio_common: Fix divide-by-zero for DIO cmdtest
  staging: erofs: fix to handle error path of erofs_vmap()
  staging: mt7621-dts: update ethernet settings.
  staging: remove mt7621-eth

Pull tty/serial fixes from Greg KH:
 "Here are some small tty and serial driver fixes for 5.1-rc3.

  Nothing major here, just a number of potential problems fixes for
  error handling paths, as well as some other minor bugfixes for
  reported issues with 5.1-rc1.

  All of these have been in linux-next with no reported issues"

* tag 'tty-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: fix NULL pointer issue when tty_port ops is not set
  Disable kgdboc failed by echo space to /sys/module/kgdboc/parameters/kgdboc
  dt-bindings: serial: Add compatible for Mediatek MT8183
  tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
  tty/serial: atmel: Add is_half_duplex helper
  serial: sh-sci: Fix setting SCSCR_TIE while transferring data
  serial: ar933x_uart: Fix build failure with disabled console
  tty: serial: qcom_geni_serial: Initialize baud in qcom_geni_console_setup
  sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()
  tty: mxs-auart: fix a potential NULL pointer dereference
  tty: atmel_serial: fix a potential NULL pointer dereference
  serial: max310x: Fix to avoid potential NULL pointer dereference
  serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 5.1-rc3.

  Nothing major at all here, just a small collection of fixes for
  reported issues, and potential problems with error handling paths.
  Also a few new device ids, as normal.

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  USB: serial: option: add Olicard 600
  USB: serial: cp210x: add new device id
  usb: u132-hcd: fix resource leak
  usb: cdc-acm: fix race during wakeup blocking TX traffic
  usb: mtu3: fix EXTCON dependency
  usb: usb251xb: fix to avoid potential NULL pointer dereference
  usb: core: Try generic PHY_MODE_USB_HOST if usb_phy_roothub_set_mode fails
  phy: sun4i-usb: Support set_mode to USB_HOST for non-OTG PHYs
  xhci: Don't let USB3 ports stuck in polling state prevent suspend
  usb: xhci: dbc: Don't free all memory with spinlock held
  xhci: Fix port resume done detection for SS ports with LPM enabled
  USB: serial: mos7720: fix mos_parport refcount imbalance on error path
  USB: gadget: f_hid: fix deadlock in f_hidg_write()
  usb: gadget: net2272: Fix net2272_dequeue()
  usb: gadget: net2280: Fix net2280_dequeue()
  usb: gadget: net2280: Fix overrun of OUT messages
  usb: dwc3: pci: add support for Comet Lake PCH ID
  usb: usb251xb: Remove unnecessary comparison of unsigned integer with >= 0
  usb: common: Consider only available nodes for dr_mode
  usb: typec: tcpm: Try PD-2.0 if sink does not respond to 3.0 source-caps
  ...

Pull ACPI fix from Rafael Wysocki:
 "This corrects a previous attempt to make Linux use its own set of ACPI
  debug flags different from the upstream ACPICA's default (Erik
  Schmauss)"

* tag 'acpi-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: use different default debug value than ACPICA

Pull power management fixes from Rafael Wysocki:
 "These fix CPU base frequency reporting in the intel_pstate driver and
  a use-after-free in the scpi-cpufreq driver.

  Specifics:

   - Fix the ACPI CPPC library to actually follow the specification when
     decoding the guaranteed performance register information and make
     the intel_pstate driver to fall back to the nominal frequency when
     reporting the base frequency if the guaranteed performance register
     information is not there (Srinivas Pandruvada).

   - Fix use-after-free in the exit callback of the scpi-cpufreq left
     after an update during the 5.0 development cycle (Vincent Stehlé)"

* tag 'pm-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: scpi: Fix use after free
  cpufreq: intel_pstate: Also use CPPC nominal_perf for base_frequency
  ACPI / CPPC: Fix guaranteed performance handling

Pull security layer fixes from James Morris:
 "Yama and LSM config fixes"

* 'fixes-v5.1-a' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  LSM: Revive CONFIG_DEFAULT_SECURITY_* for "make oldconfig"
  Yama: mark local symbols as static

Merge misc fixes from Andrew Morton:
 "22 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
  fs/proc/proc_sysctl.c: fix NULL pointer dereference in put_links
  fs: fs_parser: fix printk format warning
  checkpatch: add %pt as a valid vsprintf extension
  mm/migrate.c: add missing flush_dcache_page for non-mapped page migrate
  drivers/block/zram/zram_drv.c: fix idle/writeback string compare
  mm/page_isolation.c: fix a wrong flag in set_migratetype_isolate()
  mm/memory_hotplug.c: fix notification in offline error path
  ptrace: take into account saved_sigmask in PTRACE{GET,SET}SIGMASK
  fs/proc/kcore.c: make kcore_modules static
  include/linux/list.h: fix list_is_first() kernel-doc
  mm/debug.c: fix __dump_page when mapping->host is not set
  mm: mempolicy: make mbind() return -EIO when MPOL_MF_STRICT is specified
  include/linux/hugetlb.h: convert to use vm_fault_t
  iommu/io-pgtable-arm-v7s: request DMA32 memory, and improve debugging
  mm: add support for kmem caches in DMA32 zone
  ocfs2: fix inode bh swapping mixup in ocfs2_reflink_inodes_lock
  mm/hotplug: fix offline undo_isolate_page_range()
  fs/open.c: allow opening only regular files during execve()
  mailmap: add Changbin Du
  mm/debug.c: add a cast to u64 for atomic64_read()
  ...

Pull arm64 fix from Catalin Marinas:
 "Use memblock_alloc() instead of memblock_alloc_low() in
  request_standard_resources(), the latter being limited to the low 4G
  memory range on arm64"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: replace memblock_alloc_low with memblock_alloc

Pull IOMMU fixes from Joerg Roedel:

 - Fix a bug in the AMD IOMMU driver not handling exclusion ranges
   correctly. In fact the driver did not reserve these ranges for IOVA
   allocations, so that dma-handles could be allocated in an exclusion
   range, leading to data corruption. Exclusion ranges have not been
   used by any firmware up to now, so this issue remained undiscovered
   for quite some time.

 - Fix wrong warning messages that the IOMMU core code prints when it
   tries to allocate the default domain for an iommu group and the
   driver does not support any of the default domain types (like Intel
   VT-d).

* tag 'iommu-fixes-v5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Reserve exclusion range in iova-domain
  iommu: Don't print warning when IOMMU driver only supports unmanaged domains