- 25 4月, 2005 9 次提交
-
-
由 Bob Breuer 提交于
This enables the sun linux logo to be selected on sparc32. Signed-off-by: NBob Breuer <breuerr@mc.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tom 'spot' Callaway 提交于
Using the same logic as the other framebuffer fixes committed in 2.6.11, this is a set of fixes to make TCX functional on the console again. Adds the tcx_pan_display function, sets the all->info.var.{red,green,blue}.length values to 8, and runs fb_set_cmap. Also looks for the correct SUNW,tcx prom value. This patch just slipped through the cracks. Originally by: Georg Chini <georg.chini@triaton-webhosting.com> Signed-off-by: NTom 'spot' Callaway <tcallawa@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tom 'spot' Callaway 提交于
Minor cleanups for sparc specific drivers (sunbmac, sunqe, sunlance, sunhme, esp) so that they have a full module version definition that is consistent with other upstream drivers. Signed-off-by: NTom 'spot' Callaway <tcallawa@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Al Viro 提交于
void * __iomem foo is not a pointer to iomem - it's an iomem variable containing void *. A pile of such guys in arch/sparc64/kernel/time.c, drivers/sbus/char/rtc.c and include/asm-sparc64/mostek.h turned into intended void __iomem *. Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Missing include - usual portability problems... Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
(!ARCH_S390 && !M68K && !IA64 && !UML) is obviously always true on ARM. Intended behaviour for ARM is "absent unless we are on RiscPC or EBSA285". So what we want is added && !ARM in the first term - without it the last part (|| ARCH_RPC || ARCH_EBSA285, that is) doesn't do anything. Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Missing include, breaks at least on arm. Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
All boards dealt with by I2C_MPC are 32bit. Moreover, driver simply won't build on ppc64 - it uses ppc32-only types all over the place. Dependency fixed - it's PPC32, not PPC. Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Al Viro 提交于
Somebody forgot that | has higher priority than ?:. As the result, allocation is done with bogus flags - instead of GFP_ATOMIC + possibly GFP_DMA we always get GFP_DMA and no GFP_ATOMIC. Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 22 4月, 2005 27 次提交
-
-
由 David S. Miller 提交于
This breaks serial consoles badly. Thanks to Eric Brower for tracking down the problem. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
We were forgetting to call sunsu_change_speed(). The reason that replugging in the mouse cable "fixes things" is that causes a BREAK interrupt which in turn caused a call to sunsu_change_speed() which would get the chip setup properly. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Provide support for drivers/char/rtc.c ioctls in the Mostek rtc driver as well as the Sparc specific RTCGET and RTCSET. This allows userspace to be much less messy. Currently util-linux and other spots jump through hoops trying various ioctl variants until it hits the right one whatever driver actually being used supports. Eventually all of this should move over to the genrtc.c driver, but not today... While we are here, fix up the register types for sparse. Thanks to Frans Pop for helping point out this issue. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add MSI test for chips that support MSI. If MSI test fails, it will switch back to INTx mode and will print a message asking the user to report the failure. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add MSI support for 5751 C0 and 5752. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Fix a bug in tg3_set_eeprom() when the length is less than 4 and the offset is not 4-byte aligned. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add support for the NVRAM lock-out feature for TPM in 5752. If lock-out is enabled, certain NVRAM registers cannot be written to. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Add bit definitions for the new GPIO3 in 5752. GPIO3 must be driven as output when it is unused. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround it is to change it to the correct value in tp->pci_chip_rev_id. This way, it is easier to check for the ASIC_REV_5752 in the rest of the driver. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Fix tg3_set_power_state to drive GPIOs properly based on the TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0 and D3 power state changes. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Setup proper GPIO settings in tp->grc_local_ctrl before calling tg3_set_power() state in tg3_get_invariants() and after chip reset. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling tg3_set_power_state() in tg3_get_invariants(). This will allow tg3_set_power_state() to drive the GPIOs correctly based on the config. information in eeprom. On the 5752, there are no pull-up resistors on the GPIO pins and it is necessary to drive the unused GPIOs as output. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Some minor 5752 fixes mostly for correctness and add 5752 PHY ID. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0, and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1 to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Use check of TG3_FLG2_5750_PLUS in tg3_get_invariants to set TG3_FLG2_5705_PLUS flag. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Rewrite checks in tg3_get_invariants to use TG3_FLG2_5705_PLUS and TG3_FLG2_5750_PLUS flags. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Rewrite of a couple of troublesome multi-way if statements to use TG3_FLG2_5705_PLUS flag. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Replace a number of two-way if statements checking for 5750, and/or 5752 to reference the newly-defined TG3_FLG2_5750_PLUS flag instead. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for ASIC_REV_5750 or ASIC_REV_5752. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Replace a number of three-way if statements checking for 5705, 5750, and 5752 to reference the equivalent TG3_FLG2_5705_PLUS flag instead. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3. I did this separately in case patches like this (i.e. new PCI IDs) need to come from more "official" sources. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Add hard-coded definition of bcm5752 PCI ID to tg3_pci_tbl. Next patch will change entry to use pci_ids.h-based definition. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Add ASIC_REV_5752 definition. Track-down all references to ASIC_REV_5750 and mirror them with references to the newly defined ASIC_REV_5752. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Adrian Bunk 提交于
The untested patch below should fix this compile error. Signed-off-by: NAdrian Bunk <bunk@stusta.de> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Jody McIntyre 提交于
Fix non-legacy multichannel ISO receive, broken by Parag Wardukar's allocation fix. Multichannel ISO receive still sucks; it should be possible to use both legacy and non-legacy modes at the same time, but with this patch, things are no worse than they were in 2.6.11 and allocation is still done at the correct time. Signed-off-by: NJody McIntyre <scjody@steamballoon.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Jody McIntyre 提交于
- Print the correct value in the DBGMSG in dma_rcv_tasklet(). See OHCI 1.1 section 8.7, page 103 ff. - Print tlabels as %d everywhere. Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: NJody McIntyre <scjody@steamballoon.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 21 4月, 2005 2 次提交
-
-
由 Karsten Keil 提交于
We do not longer use DLT_LINUX_SLL for activ/pass filters but DLT_PPP_WITHDIRECTION witch need 1 as outbound flag. Signed-off-by: NKarsten Keil <kkeil@suse.de> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 James Bottomley 提交于
My version of gcc doesn't warn about this error (declaration in the middle of a set of statements). The fix is simple (this also corrects return code; for init functions it should be zero or error).
-
- 19 4月, 2005 2 次提交
-
-
由 ecashin@coraid.com 提交于
I can't use list.h, since sk_buff doesn't have a list_head but instead has two struct sk_buff pointers, and I want to avoid any extra memory allocation. send outgoing packets in order Signed-off-by: NEd L. Cashin <ecashin@coraid.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 ecashin@coraid.com 提交于
add support for disk statistics Signed-off-by: NEd L. Cashin <ecashin@coraid.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-