In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for pixel data edge.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for DE level.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for h/vsync level.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Remove the interlace member and add display_flags to omap_video_timings to
configure the interlace mode.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the vbp member to vback_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the vfp member to vfront_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the vsw member to vsync_len.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the hbp member to hback_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the hfp member to hfront_porch.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the hsw member to hsync_len.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the y_res member to vactive.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In preparation to move the stack to use the generic videmode struct for
display timing information rename the x_res member to hactive.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

All drivers to include the omapdrm/dss/omapdss.h header file. This header
includes the <video/omapdss.h>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>

We are removing the uses of 'struct omap_overlay_manager'. This patch
changes VENC driver to use 'omap_channel' instead.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DSS output drivers check 'dssdev->manager' in disconnect()
functions. This check is not needed as the manager must always be set if
the output device was connected. Remove the check.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_enable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_set_timings() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disconnect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_connect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use 'out->dispc_channel_connected' to check if the device is connected
to an overlay manager or not, instead of using 'out->manager'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that omapfb has its own copy of omapdss and display drivers, we can
move omapdss and display drivers which omapdrm uses to omapdrm's
directory.

We also need to change the main drm Makefile so that omapdrm directory
is always entered, because omapdss has a file that can't be built as a
module.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Acked-by: NRob Clark <robdclark@gmail.com>

All the output drivers check for 'out' being NULL, but it can never be
NULL. Remove the check.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Otherwise check_timings fails and we get a "has no modes" message
from xrandr.

This fix makes the venc assume PAL and NTSC timings that match the
timings synthetized by copy_timings_drm_to_omap() from omapdrm
mode settings so that check_timings() succeeds.

Tested on: BeagleBoard XM, GTA04 and OpenPandora
Signed-off-by: NH. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdss kernel module contains drivers for multiple devices, one for
each DSS submodule. The probing we have at the moment is a mess, and
doesn't give us proper deferred probing nor ensure that all the devices
are probed before omapfb/omapdrm start using omapdss.

This patch solves the mess by using the component system for DSS
submodules.

The changes to all DSS submodules (dispc, dpi, dsi, hdmi4/5, rfbi, sdi,
venc) are the same: probe & remove functions are changed to bind &
unbind, and new probe & remove functions are added which call
component_add/del.

The dss_core driver (dss.c) acts as a component master. Adding and
matching the components is simple: all dss device's child devices are
added as components.

However, we do have some dependencies between the drivers. The order in
which they should be probed is reflected by the list in core.c
(dss_output_drv_reg_funcs). The drivers are registered in that order,
which causes the components to be added in that order, which makes the
components to be bound in that order. This feels a bit fragile, and we
probably should improve the code to manage binds in random order.
However, for now, this works fine.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The following patches will add component handling to omapdss, improving
the handling of deferred probing. However, at the moment we're using
quite a lot of __inits and __exits in the driver, which prevent normal
dynamic probing and removal.

This patch removes most of the uses of __init and __exit, so that we can
register drivers after module init, and so that we can unregister
drivers even if the module is built-in.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdss drivers cannot handle devices being unbound while the devices
are part of a connected display pipeline. Module refcounts are used to
prevent unloading the modules, but one can still manually unbind the
devices via sysfs, causing crash.

Set suppress_bind_attrs to disable the bind/unbind support via sysfs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The drivers/video directory is a mess. It contains generic video related
files, directories for backlight, console, linux logo, lots of fbdev
device drivers, fbdev framework files.

Make some order into the chaos by creating drivers/video/fbdev
directory, and move all fbdev related files there.

No functionality is changed, although I guess it is possible that some
subtle Makefile build order related issue could be created by this
patch.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NRob Clark <robdclark@gmail.com>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add DT support to VENC.

In contrast to non-DT version, the DT version gets the invert-polarity
and connector type via venc's endpoint, not from the connector.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

The regulator names used for DSS components are somewhat ugly for DT
use. As we're just adding DT support, it's simple to change the
regulator names.

This patch makes the DSS driver get the regulators with somewhat cleaner
names when bootin with DT. For example, this allows us to define HDMI's
VDDA regulator in the DT data as:

vdda-supply = <...>;

instead of

vdda_hdmi_dac-supply = <...>;
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

omapdss has its own video-timings struct, but we want to move the common
videomode.

The first step is to change the omapdss's pixelclock unit from kHz to
Hz. Also, omapdss uses "pixel_clock" field name, whereas the common
videomode uses "pixelclock" field name. This patch changes the field
name also, as that makes it easy to spot any non-converted pixel_clock
uses.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Nowadays it's normal to get -EPROBE_DEFER from, e.g., regulator_get. As
-EPROBE_DEFER is not really an error, and the driver will be probed fine
a bit later, printing an error message will just confuse the user.

This patch changes omapdss to print an error for regulator_gets only if
the error code is something else than -EPROBE_DEFER.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In the old panel device model we had omap_dss_output entities,
representing the encoders in the DSS block. This entity had "device"
field, which pointed to the panel that was using the omap_dss_output.

With the new panel device model, the omap_dss_output is integrated into
omap_dss_device, which now represents a "display entity". Thus the "device"
field, now in omap_dss_device, points to the next entity in the display
entity-chain.

This patch renames the "device" field to "dst", which much better tells
what the field points to.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.

This patch removes the code from the VENC driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add "ops" style method for using analog TV functionality.

Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In order to allow multiple display block in a video pipeline, we need to
give the drivers way to register themselves. For now we have
the omapdss_register_display() which is used to register panels, and
dss_register_output() which is used to register DSS encoders.

This patch makes dss_register_output() public (with the name of
omapdss_register_output), which can be used to register also external
encoders. The distinction between register_output and register_display
is that a "display" is an entity at the end of the videopipeline, and
"output" is something inside the pipeline.

The registration and naming will be made saner in the future, but the
current names and functions are kept to minimize changes during the dss
device model transition.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC needs to know the clock rate for DIGIT (i.e. TV) channel, and this
clock is provided by either VENC or HDMI modules. Currently DISPC will
call a function in VENC/HDMI, asking what the clock rate is. This means
we have a fixed dependency from DISPC to both VENC and HDMI.

To have a more generic approach, and in particular to allow adding OMAP5
HDMI driver, we need to remove this dependency. This patch makes
VENC/HDMI inform DISPC when the their clock changes, thus reversing the
dependency and removing the issue.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Setup the owner field for DSS output's omap_dss_device so that module
refcounting works.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We currently have omap_dss_device, which represents an external display
device, sometimes an external encoder, sometimes a panel. Then we have
omap_dss_output, which represents DSS's output encoder.

In the future with new display device model, we construct a video
pipeline from the display blocks. To accomplish this, all the blocks
need to be presented by the same entity.

Thus, this patch combines omap_dss_output into omap_dss_device. Some of
the fields in omap_dss_output are already found in omap_dss_device, but
some are not. This means we'll have DSS output specific fields in
omap_dss_device, which is not very nice. However, it is easier to just
keep those output specific fields there for now, and after transition to
new display device model is made, they can be cleaned up easier than
could be done now.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>