This should help driver to deal vith KVMs that reset mice when
switching between boxes.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

These haven't worked in some time, and we've dropped support for the bus
from the SH tree until someone shows some interest in maintaining it.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Noticed by Christophe Zimmerman, this explains the slow mouse movement
with 2.6.x kernels.

And checking the 2.4.x drivers/sbus/char/sunmouse.c driver shows we
always used a 5-byte protocol with Sun mice in the past.  I have no
idea how the 3-byte thing got into the 2.6.x driver, but it's surely
wrong.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This DMI data was found in Fujitsu LifeBook B142 (Product S/N
FPC01003B, italian keyboard); re: bugzilla #5335
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

It looks like quite a few mice out there treat PSMOUSE_RESET_DIS
as a powerdown request and turn off the light rendering the mouse
unusable.

Vojtech recommended to switch from PSMOUSE_RESET_DIS to full reset,
however we don't want to do that everywhere as full reset is pretty
slow. Instead we only use it before probing for "generic" protocols,
such as IntelliMouse and Explorer, to make sure that the mouse will
be woken up if it went to sleep as a result of PSMOUSE_RESET_DIS
issued earlier.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Without this patch Forward and Backward buttons on the touchpad do not
generate any events.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

CONFIG_PC is left-over cruft after the introduction of CONFIG_X86_PC with
the subarch split.  Remove it, and fixup the remaining users to depend on
CONFIG_X86_PC instead.
Signed-off-by: NArthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Input: convert drivers/input/mouse to dynamic input_dev allocation

This is required for input_dev sysfs integration
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Update drivers to new input layer changes.
Signed-off-by: NHelge Deller <deller@parisc-linux.org>
Signed-off-by: NMatthew Wilcox <willy@parisc-linux.org>

Reorder code in gscps2_interrupt() and only enable ports when opened.
This fixes issues with hangs booting an SMP kernel on my C360.
Previously serio_interrupt() could be called before the lock in
struct serio was initialised.
Signed-off-by: NRichard Hirst <rhirst@parisc-linux.org>
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Rearrange attribute code to use generic show and set handlers
instead of replicating them for every attribute; switch to
using attribute_group instead of creating all attributes
manually. All this saves about 4K.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Synaptics driver used child->type to select either 3-byte or 4-byte
packet size for the pass-through port; this gives wrong results for
the newer protocols. Change the check to use child->pktsize instead.
Signed-off-by: NSergey Vlasov <vsu@altlinux.ru>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

There are wheel mice that respond to Logitech probes and report
that they have only 2 buttons (such as e-Aser mouse) and this
stops the wheel from being used as a middle button. Change the
driver to always report BTN_MIDDLE capability if a wheel is
present.

Also, never reset BTN_RIGHT capability in logips2pp code - there
are no Logitech mice that have only one button and if some other
mice happen to respond to Logitech's query we could do the wrong
thing.
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The condition in alps_init() was also inverted and the driver
was enabling tapping mode only if it was already enabled.
Signed-off-by: NPeter Osterlund <petero2@telia.com>
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The driver would not reset pass-through mode when performing
resume of a DualPoint touchpad causing it to stop working
until next reboot.
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Toshiba Dynabooks require the same workaround as Satellites -
Synaptics report rate should be lowered to 40pps (from 80),
otherwise KBC starts losing keypresses.
Signed-off-by: NSimon Horman <horms@valinux.co.jp>
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

[PATCH] Driver Core: drivers/i2c/chips/w83781d.c - drivers/s390/block/dcssblk.c: update device attribute callbacks
Signed-off-by: NYani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It looks like logic for enabling hardware tapping in ALPS driver was
inverted and we enable it only if it was already enabled by BIOS or
firmware.

I have a confirmation from one user that the patch below fixes the problem
for him and it might be beneficial if we could get it into 2.6.12.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

       to allow easy switching at run-time.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

       given number of bytes from device. Change ps2_command to
       allow using 0 as command ID and actually pass it to the
       device instead of working as a drain.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

       operations do not iterfere with each other.
       Also make sure that serio core takes serio->drv_sem
       not only for connect/disconnect but for reconnect
       too.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

I have an Ahtec laptop with a ALPS GlidePoint device, with 4 buttons.
With Linux hernel 2.6.12rc4 and rc5 I'm unable to use the vertical
scroll buttons (BACK and FORWARD).

BACK gets detected as BTN_MIDDLE and FORWARD is undetected.

I've modified the drivers/input/mouse/alps.c from 2.6.12rc5 and now it
works fine!
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

       compared to "classic" PS/2 mice, provide appropriate
       resolution setting handler.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

       the rest of protocols in preparation to dynamic protocol
       switching.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

       - do not try to set rate and resolution in init method, let
         psmouse core do it for us. This also removes special quirks
         from the core;
       - do not disable mouse before doing full reset - meaningless;
       - some formatting and whitespace cleanups.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

From: Kenan Esau <kenan.esau@conan.de>
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

       core takes care of calling open and close methods only
       when needed.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

       is no reason one driver should take 10 lines in dmesg.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

       sends an incorrect ID and wasn't recognized.
Reported-by: NStefan Seyfried <seife@suse.de>
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

ALPS needs to be reset for detection to work reliably when reconnecting.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make the alps printk output look consistent.

Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>