Au1x00/RT2800+ doesn't implement the 8250 scratch register (and
this may be true of other h/w currently supported by the 8250 driver);
read back the canary value written to the scratch register to enable
the console h/w restart after resume from system suspend.

Fixes: 4516d50a ("serial: 8250: Use canary to restart console ...")
Reported-by: NMason <slash.tmp@free.fr>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Au1x00/RT2800+ hardware has an alternate register layout which is
remapped with lookup tables by the au_serial_in()/out() i/o accessors.
However, the h/w does not support the complete 8250 register set, and
accesses to unmapped registers cause out-of-bounds lookups. Further,
because the lookup tables are defined by designated initializers, the
tables may contain unmapped entries (although the current tables do not).

Declare fixed-size lookup tables with contiguous initialization for
the complete 8250 register map; unmapped registers are initialized to -1.
Validate the register index (ie., 'offset') is in the range [0, table size).
Return fixed value for unmapped register reads and ignore unmapped register
writes.
Reported-by: NMason <slash.tmp@free.fr>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The base port operations dispatch table should never be modified
at runtime; the proper way to override base port operations is
to dup the port operations, modify the copy, and point port->ops
at the copy.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare for 8250 split; separate RSA probe and resource management
from base port operations. Override base port operations for the
config_port(), request_port() and release_port() methods to
implement the optional RSA probe and resource management only in
the universal/legacy 8250 driver.

Introduce 'probe' flags for 8250 ports, which allows drivers higher
up the driver stack to enable optional probes.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The probe for Remote Supervisor Adapter is limited to port i/o
addresses which match one of the probe_rsa[] module parameter
addresses. Limit RSA resource acquire to matching i/o ports.

The result is a saner probe policy: only perform optional probes
when specified rather than by default.

NB: It is possible for userspace to set the port type == PORT_RSA
with ioctl(TIOCSSERIAL) and then autoconfig with ioctl(TIOCSERCONFIG),
which if it fails, may leave the port type set to PORT_RSA. Since
this may have previously resulted in a working RSA port, this behavior
is preserved.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Support for Remote Supervisor Adapter is conditional on
CONFIG_SERIAL_8250_RSA; only attempt RSA resource acquire if
defined.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare for 8250 split; move default dma tx/rx handler initialization
into serial8250_set_defaults(), which allows default dma ops to
remain unexported from the base port operations module after the split.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare for 8250 split; move fixed type initialization into
serial8250_set_defaults(). This enables uart_config[] array to remain
file scope in base port operations after the split.

NB: the call to serial8250_init_fixed_type_port() from
serial8250_register_ports() was added by commit b5d228cc
("serial: copy UART properties of UPF_FIXED_TYPE ports provisioned
using early_serial_setup") specifically to support ports initialized
by early_serial_setup(). Since serial8250_set_defaults() is called
from early_serial_setup(), fixed type initialization is now already
handled there before serial8250_register_ports() is called.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare for 8250 split; introduce serial8250_set_defaults() to set default
port methods prior to driver override.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare for 8250 split; introduce serial8250_init_port() to initialize
port fields uncoupled from port structure storage.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare for 8250 split; decouple irq setup/teardown and handler from
core port operations.

Introduce setup_irq() and release_irq() 8250 driver methods; the 8250
core will use these methods to install and remove irq handling for
the given 8250 port.

Refactor irq chain linking/unlinking from 8250 core into
univ8250_setup_irq()/univ8250_release_irq() for the universal 8250 driver.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare for 8250 core split; separate shared console interface from the
console definition of the universal driver.

Introduce 8250 shared console interface; serial8250_console_write() and
serial8250_console_setup() which decouples the console operation from
the port structure storage.

Rename existing serial8250_console* identifiers to univ8250_console*.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add match() method to struct console which allows the console to
perform console command line matching instead of (or in addition to)
default console matching (ie., by fixed name and index).

The match() method returns 0 to indicate a successful match; normal
console matching occurs if no match() method is defined or the
match() method returns non-zero. The match() method is expected to set
the console index if required.

Re-implement earlycon-to-console-handoff with direct matching of
"console=uart|uart8250,..." to the 8250 ttyS console.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare for 8250 split; initialize the port flags based on the
"skip_txen_test" module param to use the existing flag test.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare for 8250_core.c file split; move shared inline function
to local header file.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since uart->port.type has just reset to PORT_UNKNOWN, capabilities
are reset to uart_config[PORT_UNKNOWN].flags, which is 0.

Removes unnecessary dependency on uart_config[].
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

set_io_from_upio() already initializes ->handle_irq to
serial8250_default_handle_irq.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare for 8250 split; calculate the ttyS index directly from
the port minor which avoids the global serial8250_reg reference
from base port operations.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

No functional changes.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 0aa525d1.

The conditional RX-FIFO read seems to cause spurious interrupts and we
see just:
|serial8250: too much work for irq29

The previous behaviour was "default" for decades and Marvell's 88f6282 SoC
might not be the only that relies on it. Therefore the Omap fix is
reverted for now.

Fixes: 0aa525d1 ("tty: serial: 8250_core: read only RX if there is
something in the FIFO")
Reported-By: NNicolas Schichan <nschichan@freebox.fr>
Debuged-By: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

UARTs which do not trigger THRE interrupt if the fifo is already
empty when the interrupt is enabled need tx primed manually. These
UARTs are identified by the UART_BUG_TXEN flag to enable the
required workaround.

However, the current workaround is broken; if the fifo is already
empty but the shifter is still transmitting, then serial8250_tx_chars()
will not be called but no further THRE interrupt will occur, and
tx will stall. The appropriate check is for fifo empty (THRE), not
transmitter empty (TEMT).
Signed-off-by: NDick Hollenbeck <dick@softplc.com>
[pjh: rewrote commit log]
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/8250/8250_core.c:2503:6: sparse: symbol 'serial8250_set_divisor' was not declared. Should it be static?
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The port shadow registers, ->fcr and ->mcr, must be protected from
concurrent updates. Relocate the shadow register updates in
serial8250_do_set_termios() to the port lock critical section.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When using no_console_suspend, the serial console may be powered off
anyway during system sleep. Upon resume, the port may be in its default
power-on state, but is expected to continue console i/o before the device
has received its pm callback. The resultant garbage i/o can cause all
kinds of havoc on the remote end.

Use the scratch register as a canary to discover if the console
has been powered-off. Write a non-zero value to the scratch register
at port suspend and reprogram the port before any console i/o if the
scratch register != canary before port resume.

This workaround is disabled for omap_8250 (which uses different divisor
programming).

Credit to Doug Anderson <dianders@chromium.org> for the idea of using
the scratch register canary to discover port power-down.

Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Exar XR17V35X PCIe uarts support a 4-bit fractional divisor register.
Refactor the divisor calculation from the divisor programming.

Allow a fractional result from serial8250_get_divisor() and pass this
result to serial8250_dl_write().

Simplify the calculation for quot and quot_frac. This was verified
to be identical to the results of the original calculation with a test
jig.

NB: The results were also compared with the divisor value chart
on pg 33 of the Exar XR17V352 datasheet, rev 1.0.3, here:
http://www.exar.com/common/content/document.ashx?id=1585
which differs from the calculated values by 1 in the fractional result.
This is because the calculated values are still rounded in the
fractional result, whereas the table values are truncated. Note
that the data error rate % values in the datasheet are for
rounded fractional results, as the truncated fractional results
have more error.

Cc: Joe Schultz <jschultz@xes-inc.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor divisor register programming into a new function,
serial8250_set_divisor; this allows serial console to reinitialize
early after resume from suspend.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor the computation of the LCR register value from termios c_cflag
into a new local function, serial8250_compute_lcr().
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The UART_BUG_QUOT workaround adjusts the divisor computed from the
baud rate by serial8250_get_divisor(). Move the workaround into
serial8250_get_divisor(), so that divisor-from-baud computation
is encapsulated.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since we return in the first branch the second one doesn't require an
additional else keyword. The patch removes it.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some of FSL SoCs like T1040 has new version of UART controller which
can support 64byte FiFo.
To enable 64 byte support, following needs to be done:
-FCR[EN64] needs to be programmed to 1 to enable it.
-Also, when FCR[EN64]==1, RTL bits to be used as below
to define various Receive Trigger Levels:
        -FCR[RTL] = 00  1 byte
        -FCR[RTL] = 01  16 bytes
        -FCR[RTL] = 10  32 bytes
        -FCR[RTL] = 11  56 bytes
-tx_loadsz is set to 63-bytes instead of 64-bytes to implement
 workaround of errata A-008006 which states that tx_loadsz should
 be configured less than Maximum supported fifo bytes
Signed-off-by: NVijay Rai <vijay.rai@freescale.com>
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The OMAP3 UART ignores MCR[1] (ie., UART_MCR_RTS) when in autoRTS
mode (UPF_HARD_FLOW + CRTSCTS). This makes it impossible for either
the serial core or userspace to manually flow control the sender.

Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.

Note that the OMAP3 UART provides no mechanism for switching from
autoRTS mode without corrupting incoming data; to access the
necessary register, the line control settings must be set to 8-e-2
and thus any data received during that time will be interpreted with
those settings. This corruption has been observed in practice.

Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Attempting to use SysRq via the 8250 serial port with spin lock
debugging on on a uniprocessor system results in the following splat:

 SysRq :
 BUG: spinlock trylock failure on UP on CPU#0, swapper/0
  lock: serial8250_ports+0x0/0x8c0, .magic: dead4ead, .owner: swapper/0, .owner_cpu: 0
 CPU: 0 PID: 0 Comm: swapper Not tainted 3.18.0-rc4+ #37
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
  ffffffff8245ba00 ffffffff81628b28 ffffffff812c8d27 ffffffff81628b48
  ffffffff8106812e ffffffff8245ba00 ffffffff814e22ed ffffffff81628b68
  ffffffff810681a6 0000000000000000 0000000000000000 ffffffff81628b88
 Call Trace:
  <IRQ>  [<ffffffff812c8d27>] dump_stack+0x19/0x1b
  [<ffffffff8106812e>] spin_dump+0x7e/0xd0
  [<ffffffff810681a6>] spin_bug+0x26/0x30
  [<ffffffff8106843c>] do_raw_spin_trylock+0x4c/0x60
  [<ffffffff812cdb1d>] _raw_spin_trylock+0x1d/0x60
  [<ffffffff812336d8>] serial8250_console_write+0x68/0x190
  [<ffffffff811eb0b0>] ? sprintf+0x40/0x50
  [<ffffffff8106ab5e>] call_console_drivers.constprop.11+0x9e/0xf0
  [<ffffffff8106b276>] console_unlock+0x3e6/0x490
  [<ffffffff8106b595>] vprintk_emit+0x275/0x530
  [<ffffffff812c869a>] printk+0x4d/0x4f
  [<ffffffff8121e612>] __handle_sysrq+0x62/0x1b0
  [<ffffffff8121e5b5>] ? __handle_sysrq+0x5/0x1b0
  [<ffffffff8121ebc6>] handle_sysrq+0x26/0x30
  [<ffffffff81233157>] serial8250_rx_chars+0x1d7/0x250
  [<ffffffff812338bb>] serial8250_handle_irq+0x7b/0x90
  [<ffffffff812338f3>] serial8250_default_handle_irq+0x23/0x30
  [<ffffffff812318b3>] serial8250_interrupt+0x63/0xe0
  [<ffffffff8106d80e>] handle_irq_event_percpu+0x4e/0x200
  [<ffffffff8106da01>] handle_irq_event+0x41/0x70
  [<ffffffff810701ee>] ? handle_edge_irq+0x1e/0x110
  [<ffffffff8107026e>] handle_edge_irq+0x9e/0x110
  [<ffffffff810041c2>] handle_irq+0x22/0x40
  [<ffffffff812d096e>] do_IRQ+0x4e/0xf0
  [<ffffffff812cf4ed>] common_interrupt+0x6d/0x6d
  <EOI>  [<ffffffff8100acbf>] ? default_idle+0x1f/0xd0
  [<ffffffff8100acbd>] ? default_idle+0x1d/0xd0
  [<ffffffff8100b61f>] arch_cpu_idle+0xf/0x20
  [<ffffffff8105c1db>] cpu_startup_entry+0x25b/0x360
  [<ffffffff812c726e>] rest_init+0xbe/0xd0
  [<ffffffff816a4dcb>] start_kernel+0x339/0x346
  [<ffffffff816a4495>] x86_64_start_reservations+0x2a/0x2c
  [<ffffffff816a4589>] x86_64_start_kernel+0xf2/0xf6
 HELP : loglevel(0-9) reboot(b) crash(c) show-all-locks(d) te...

Before ebade5e8 ("serial: 8250: Clean up the locking for -rt")
this was handled by not even attempting to try the lock if port->sysrq,
since it is known to be taken by the interrupt handler; see
https://bugzilla.kernel.org/show_bug.cgi?id=6716#c1.  Restore that
behavior.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In serial8250_rx_chars(), max_count is set to 256. Due to the
post-decrement operator used in the while() condition, the maximum
number of iterations actually 257. This is not a problem, but it is
mildly surprising if you're debugging. Use pre-decrement instead.
Signed-off-by: NFrans Klaver <frans.klaver@xsens.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no more users for this functions. All the 8250 drivers are
using the rs485 handler on serial_core instead.
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Initialize recently added rs485 fields on serial_core
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Switching to the N_PPS line discipline may require enabling
modem status interrupts; conversely switching from N_PPS may
require disabling modem status interrupts.

Affected drivers:
8250
amba-pl010
atmel

Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Three UART drivers (8250, atmel & amba-pl010) directly call their
enable_ms() method; the uart port lock must be acquired before
any h/w programming.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

UART drivers which enable modem status interrupts when switching
to N_PPS line discipline need to determine if modem status
interrupts should be disabled when switching from N_PPS.
Specifically, the set_ldisc() notification needs to evaluate
UART_ENABLE_MS() which requires termios->c_cflag.

Convert in-tree UART drivers to new interface.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Ralink RT2880 SoC and its successors have an internal 8250 core. This core
needs the same quirks applied as the AMD AU1xxx uart. In addition to these
quirks, the ports memory region is only 0x100 unlike the AU1xxx which has a
size of 0x1000.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We have (or will have) custom DMA callbacks in the omap driver due to
the different behaviour in the RX and TX case. To make this work
we need a few changes in the IRQ handler to invoke the rx_handler again
after the "manual" mode or retry the tx_handler again before falling
back to the manual mode.

Heikki didn't want to see the extra hacks in the generic / default irq
handler and Peter wasn't too happy about an OMAP-only IRQ handler. The
way I planned it is to use this extra IRQ routine only in DMA case. If
Peter dislike this approach then I hope Heikki doesn't block changes in
the default IRQ handler :)
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>