Let's introduce ULT and ULX Kabylake definitions and start
using it for a propper DDI buffer translation.

v2: Remove extra white space. (Paulo)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

Currently we disable some parts of FDI setup after a failed link
training. But despite that we continue with the modeset as if everything
is fine. This results in tons of noise from the state checker, and
it means we're not following the proper modeset sequence for the rest of
crtc enabling, nor for crtc disabling.

Ideally we should abort the modeset and follow the proper disable
sequence to shut off everything we enabled so far, but that would
require a big rework of the modeset code. So instead just leave FDI
up and running in its untrained state, and log an error. This is
what we do on older platforms too.

v2: Fix a typo in the commit message
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449260570-14670-1-git-send-email-ville.syrjala@linux.intel.com

The .get_config() hooks should not reference anything in crtc->config,
everything should be based on the passed in pipe_config instead. So
don't dig out the cpu_transcoder from crtc->config on ddi platfforms,
and also avoid using the encoder->crtc link and instead look up the
pipe via pipe_config->base.crtc.

I don't think this will actually fix anything since during the initial
state readout we set up the encoder->crtc link prior to calling
.get_config(), and during the modeset state check the encoder->crtc
ought to be correct anyway since it's that state we just programmed.
But this seems the right thing to do anyway.

While at it, do some house cleaning on the local variables in the
.infoframe_enabled() hooks.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448555227-31403-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.

This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.

The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.

As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
  lea    0x70024(%rdx,%rax,1),%r9d
  mov    $0x1,%edx
- movslq %r9d,%r9
- mov    %r9,%rsi
- mov    %r9,-0x58(%rbp)
- callq  *0xd8(%rbx)
+ mov    %r9d,%esi
+ mov    %r9d,-0x48(%rbp)
 callq  *0xd8(%rbx)

So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.

v2: i915_mmio_reg_{offset,equal,valid}() helpers added
    s/_REG/_MMIO/ in the register defines
    mo more switch statements left to worry about
    ring_emit stuff got sorted in a prep patch
    cmd parser, lrc context and w/a batch buildup also in prep patch
    vgpu stuff cleaned up and moved to a prep patch
    all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com

When diagnosing a unrelated bug for someone on irc, it would seem the hardware can
be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.

Right now this is not handled well in i915, and it calculates the crtc needs to
be reprogrammed on the first modeset without SSC, but  the SPLL itself was kept
active. Fix this by exposing SPLL as a shared pll that will not be returned
by intel_get_shared_dpll; you have to know it exists to use it.

Changes since v1:
- Create a separate dpll_hw_state.spll for spll, and use
  separate pll functions for spll.
Tested-by: NEmil Renner Berthing <kernel@esmil.dk>
Tested-by: NGabriel Feceoru <gabriel.feceoru@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447681332-6318-1-git-send-email-maarten.lankhorst@linux.intel.comSigned-off-by: NJani Nikula <jani.nikula@intel.com>

Before this patch, we used the intel_display_power_{get,put} functions
to make sure the PW1 and Misc I/O power wells were enabled all the
time while LCPLL was enabled. We called a get() at
intel_ddi_pll_init() when we discovered that LCPLL was enabled, then
we would call put/get at skl_{un,}init_cdclk().

The problem is that skl_uninit_cdclk() is indirectly called by
intel_runtime_suspend(). So it will only release its power well
_after_ we already decided to runtime suspend. But since we only
decide to runtime suspend after all power wells and refcounts are
released, that basically means we will never decide to runtime
suspend.

So what this patch does to fix that problem is move the PW1 + Misc I/O
power well handling out of the runtime PM mechanism: instead of
calling intel_display_power_{get_put} - functions that touch the
refcount -, we'll call the low level intel_power_well_{en,dis}able,
which don't change the refcount. This way, it is now possible for the
refcount to actually reach zero, and we'll now start runtime
suspending/resuming.

v2 (from Paulo):
  - Write a commit message since the original patch left it empty.
  - Rebase after the intel_power_well_{en,dis}able rename.
  - Use lookup_power_well() instead of hardcoded indexes.

Testcase: igt/pm_rpm/rte (and every other rpm test)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92211
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92605Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-4-git-send-email-imre.deak@intel.com

While comparing the B-Spec with the code I noticed that several
values in these tables have been updated in the spec, so I
changed the code to match..

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJim Bride <jim.bride@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446852654-883-1-git-send-email-jim.bride@linux.intel.com

The i_boost level in the DDI translation tables are stored per level.
However, skl_ddi_set_iboos() would choose an entry of that table based
on the port argument.

Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NJim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447247754-802-1-git-send-email-ander.conselvan.de.oliveira@intel.com

Set up the DDI->PLL mapping on SKL also for MST links. Might help make
MST operational on SKL.

v2: Rebased due to KBL
    Improve the patch subject, Jesse provided the new one

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1439826380-18403-1-git-send-email-ville.syrjala@linux.intel.com
References: https://bugs.freedesktop.org/show_bug.cgi?id=91791Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The bspec indicates that DDI A using four lanes is the only valid
configuration for Broxton (Broxton doesn't have a DDI E to split these
lanes with); the DDI_A_4_LANES bit of port A's DDI_BUF_CTL should always
be set by the BIOS.  However some BIOS versions seem to only be setting
this bit if eDP is actually lit up at boot time; if the BIOS doesn't
turn on the eDP panel because an external display is plugged in, then
this bit is never properly initialized.  The end result of this is that
we wind up calculating a lower max data rate than we should and may wind
up rejecting the native mode for panels that we should be able to drive.

Let's workaround this BIOS bug by just turning the DDI_A_4_LANES bit on
in our driver's internal state if we recognize that we're running on BXT
where it should have been on anyway.

Cc: Imre Deak <imre.deak@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Tested-by: NBob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446764012-27251-1-git-send-email-matthew.d.roper@intel.com

In order to prepare for a link training with DDI, the state machine
would call intel_ddi_prepare_link_retrain(). To remove the dependency to
the hardware information, replace that direct call with a callback.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-7-git-send-email-ander.conselvan.de.oliveira@intel.com

Kabylake is a Intel® Processor containing Intel® HD Graphics
following Skylake.

It is Gen9p5, so it inherits everything from Skylake.

Let's start by adding the platform separated from Skylake
but reusing most of all features, functions etc. Later we
rebase the PCI-ID patch without is_skylake=1
so we don't replace what original Author did there.

Few IS_SKYLAKEs if statements are not being covered by this patch
on purpose:
   - Workarounds: Kabylake is derivated from Skylake H0 so no
     		  W/As apply here.
   - GuC: A following patch removes Kabylake support with an
     	  explanation: No firmware available yet.
   - DMC/CSR: Done in a separated patch since we need to be carefull
     	      and load the version for revision 7 since
	      Kabylake is Skylake H0.

v2: relative cleaner commit message and added the missed
    IS_KABYLAKE to intel_i2c.c as pointed out by Jani.

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

v2: Rebase due to SKL_DPLLx usage
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1442595836-23981-21-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Revision checks are almost always accompanied by a platform check. (The
exceptions are platform specific code.) Add helpers to check for a
platform and a revision range: IS_SKL_REVID() and IS_BXT_REVID(). In
most places this simplifies and clarifies the code. It will be obvious
that revid macros are used for the correct platform.

This should make it easier to find all the revision checks for
workarounds for each platform, and make it easier to remove them once we
drop support for early hardware revisions.

This should also make it easier to differentiate between Skylake and
Kabylake revision checks when Kabylake support is added.

v2: rebase
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445343722-3312-3-git-send-email-jani.nikula@intel.com

Prefer inclusive ranges for revision checks rather than "below B0". Per
specs A2 is not used, so revid <= A1 matches revid < B0.
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1445343722-3312-2-git-send-email-jani.nikula@intel.comSigned-off-by: NJani Nikula <jani.nikula@intel.com>

Especially in cases where pre-os does not enable display, cdclk might
not be in sane state. During sanitization initialize cdclk with maximum
value till we get dynamic cdclk support.

v2: Check if BIOS programmed correctly rather than always calling init
    - Do validation of programmed cdctl and what it is expected
    - Only do slk_init_cdclk if validation failed else reuse BIOS
      programmed value

v3: Move the validation logic in a separate sanitize function (Ville)

v4: No need to check LCPLL after sanitize and use max_cdclk_freq instead
    of hardcoded value (Ville)

Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445344992-14658-1-git-send-email-shobhit.kumar@intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The link training functions had confusing names. The start function
actually does the clock recovery phase of the link training, and the
complete function does the channel equalization. So call them that
instead. Also, every call to intel_dp_start_link_train() was followed
by a call to intel_dp_complete_link_train(), so add a new start
function that calls clock_recory and channel_equalization.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

SKL and BXT qualifies the HAS_DDI() check, and hence haswell
modeset functions are re-used for modeset sequence. But DDI
interface doesn't include support for DSI.
This patch adds:
1. cases for DSI encoder, in those modeset functions and allows
   a CRTC modeset
2. Adds call to pre_pll enabled from CRTC modeset function. Nothing
   needs to be done as such in CRTC for DSI encoder, as PLL, clock
   and and transcoder programming will be taken care in encoder's
   pre_enable and pre_pll_enable function.

v2: Fixed Jani's review comments. Added INVALID_PORT for non DDI
    encoder like DSI for platforms having HAS_DDI as true.

v3: Rebased on latest drm-nightly branch. Added a WARN_ON for invalid
    encoder.

v4: WARN_ON for invalid encoder is refactored as per Jani's suggestion.
    Fixed the sequence for pre_pll_enable.

v5: Protected DDI code paths in case of DSI encoder calls.
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Use SKL_DPLLx symbolic names instead of raw numbers
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make the alternatives stand  out better.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's more useful to limp on than bring the kernel down. Hitting this is
a more likely event with BXT DSI, although care should be taken not to
call the function for DSI.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Bspec update tells that we have to enable oscaledcompmethod instead of
ouniqetrangenmethod for enabling scale value during swing programming.

v2: Adding back 'don't care' values to bxt_ddi_translations_dp and add
error message if ouniquetrangemethod was set (Imre)
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>(v1)
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Adding voltage swing table for edp to support low vswings.

v2: Rebased.
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

FIXME: Should there be a WARN(i != 9) or something, or what does the
entry 9 comment mean?
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Not the first time! not the last time?

There is a possibility to use gcc 5's -Wbool-compare to try and compare
(reg) in those macros to a constant and gcc will warn that the
comparison between a boolean expression and a constant is always either
true or false. Maybe.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Use port_clock instead of link_bw when picking the PLL parameters for
DP. link_bw may be zero with an eDP 1.4 sink that supports
DP_LINK_RATE_SET so we shouldn't use it for anything other than feed it
to the sink appropriately.

v2: Fix typo in commit message (Sivakumar)
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
[Jani: cherry-picked from future.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.

Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.

Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.

Fixes a regression with MST caused by:
 commit 90a6b7b0
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Mon Jul 6 16:39:15 2015 +0300

    drm/i915: Move intel_dp->lane_count into pipe_config

v2: Different apporoach that should keep intel_dp_check_mst_status()
    somewhat less oopsy

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

SKL-Y can now use the same programming for all VccIO values after an
adjustment to I_boost.  SKL-U DP table adjustments.

1. Remove SKL Y 0.95V from "SKL H and S" columns in all tables. The
   other SKL Y column removes the "0.85V VccIO" so it now applies to all
   voltages.

2. DP table changes SKL U 400mV+0db dword 0 value from 2016h to 201Bh.

3. DP table changes SKL U 600mv+0db dword 0 value from 2016h to 201Bh.

4. DP table increases I_boost to level 3 for SKL Y 400mv+9.5db.

v2: Fix compilation warnings as pointed by Paulo.

Reference: Graphics Spec Change r97962
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[Jani: reformatted commit message for shorter lines.]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.

v2: Add missing ':' to the pipe config debug dump
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

All the *_ddi_pll_select() functions get passed the port_clock and pipe
config as parameters. We only need to pass the pipe config, and the
functions can dig up the port_clock themselves.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use port_clock instead of link_bw when picking the PLL parameters for
DP. link_bw may be zero with an eDP 1.4 sink that supports
DP_LINK_RATE_SET so we shouldn't use it for anything other than feed it
to the sink appropriately.

v2: Fix typo in commit message (Sivakumar)
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

WA for BXT A0/A1, where DDIB's HPD pin is swapped to DDIA, so enabling
DDIA HPD pin in place of DDIB.

v2: For DP, irq_port is used to determine the encoder instead of
hpd_pin and removing the edp HPD logic because port A HPD is not
present(Imre)
v3: Rebased on top of Imre's patchset for enabling HPD on PORT A.
Added hpd_pin swapping for intel_dp_init_connector, setting encoder
for PORT_A as per the WA in irq_port (Imre)
v4: Dont enable interrupt for edp, also reframe the description (Siva)
v5: Don’t check for PORT_A in intel_ddi_init to update dig_port,
instead avoid setting hpd_pin itself (Imre)
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

An OEM may request increased I_boost beyond the recommended values
by specifying an I_boost value to be applied to all swing entries for
a port. These override values are specified in VBT.

v2: rebase and remove unused iboost_bit variable

Issue: VIZ-5676
Signed-off-by: NAntti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is no correspondent Aux channel for DDI-E.

So we need to rely on VBT to let us know witch one
is being used instead.

v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.

Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NXiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drivers/gpu/drm/i915/intel_ddi.c: In function ‘intel_prepare_ddi’:
drivers/gpu/drm/i915/intel_ddi.c:517:6: warning:
‘ddi_translations_fdi’ may be used uninitialized in this function
[-Wmaybe-uninitialized]
   if (ddi_translations_fdi)
      ^
drivers/gpu/drm/i915/intel_ddi.c:446:30: note: ‘ddi_translations_fdi’
was declared here
  const struct ddi_buf_trans *ddi_translations_fdi;
                              ^

This line used to be there, but was removed by:

commit f8896f5d
Author: David Weinehall <david.weinehall@linux.intel.com>
Date:   Thu Jun 25 11:11:03 2015 +030
    drm/i915/skl: Buffer translation improvements

Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch contains changes based on 2 updates to the spec:
Port PLL VCO restriction raised up to 6700.
Port PLL now needs DCO amp override enable for all VCO frequencies.

v2: Sonika's review comment addressed
	- dcoampovr_en_h variable not required
Based on a discussion with Siva, the following changes have been made.
	- replace dco_amp var with #define BXT_DCO_AMPLITUDE
	- set pll10 in a single assignment

v3:
Move DCO amplitude default value to i915_reg.h. Suggested by Siva.
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com> [v2]
[danvet: Spell out BUN since not everyone knows what this means.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Take the HDMI 12bpc mode and pixel repeat into account when extracting
the dotclock from the hardware on DDI platforms.

Tested on HSW only.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-and-tested-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For the purpose of state checking we only care about the DPLL HW flags
that we actually program, so mask off the ones that we don't.

This fixes one set of DPLL state check failures.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add support for reading out the HW state for DDI ports. Since the actual
programming is very similar to the CHV/VLV DPIO PLL programming we can
reuse much of the logic from there.

This fixes the state checker failures I saw on my BXT with HDMI output.

v2:
- rebased on v2 of patch 4/5
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>