Add rate limiting of the 'pp done time out' warnings since these
warnings can quickly fill the dmesg buffer.
Signed-off-by: NBrian Masney <masneyb@onstation.org>
Signed-off-by: NRob Clark <robdclark@chromium.org>

This partially reverts the DMA API support that was recently merged
because it was causing performance regressions on older Tegra devices.
Unfortunately, the cache maintenance performed by dma_map_sg() and
dma_unmap_sg() causes performance to drop by a factor of 10.

The right solution for this would be to cache mappings for buffers per
consumer device, but that's a bit involved. Instead, we simply revert to
the old behaviour of sharing IOVA mappings when we know that devices can
do so (i.e. they share the same IOMMU domain).

Cc: <stable@vger.kernel.org> # v5.5
Reported-by: NDmitry Osipenko <digetx@gmail.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Tested-by: NDmitry Osipenko <digetx@gmail.com>
Reviewed-by: NDmitry Osipenko <digetx@gmail.com>

Older Tegra devices only allow addressing 32 bits of memory, so whether
or not the host1x is attached to an IOMMU doesn't matter. host1x IOMMU
attachment is only needed on devices that can address memory beyond the
32-bit boundary and where the host1x doesn't support the wide GATHER
opcode that allows it to access buffers at higher addresses.

Cc: <stable@vger.kernel.org> # v5.5
Signed-off-by: NThierry Reding <treding@nvidia.com>
Tested-by: NDmitry Osipenko <digetx@gmail.com>
Reviewed-by: NDmitry Osipenko <digetx@gmail.com>

Disabling a display on MST can potentially happen after the entire MST
topology has been removed, which means that we can't communicate with
the topology at all in this scenario. Likewise, this also means that we
can't properly update payloads on the topology and as such, it's a good
idea to ignore payload update failures when disabling displays.
Currently, amdgpu makes the mistake of halting the payload update
process when any payload update failures occur, resulting in leaving
DC's local copies of the payload tables out of date.

This ends up causing problems with hotplugging MST topologies, and
causes modesets on the second hotplug to fail like so:

[drm] Failed to updateMST allocation table forpipe idx:1
------------[ cut here ]------------
WARNING: CPU: 5 PID: 1511 at
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:2677
update_mst_stream_alloc_table+0x11e/0x130 [amdgpu]
Modules linked in: cdc_ether usbnet fuse xt_conntrack nf_conntrack
nf_defrag_ipv6 libcrc32c nf_defrag_ipv4 ipt_REJECT nf_reject_ipv4
nft_counter nft_compat nf_tables nfnetlink tun bridge stp llc sunrpc
vfat fat wmi_bmof uvcvideo snd_hda_codec_realtek snd_hda_codec_generic
snd_hda_codec_hdmi videobuf2_vmalloc snd_hda_intel videobuf2_memops
videobuf2_v4l2 snd_intel_dspcfg videobuf2_common crct10dif_pclmul
snd_hda_codec videodev crc32_pclmul snd_hwdep snd_hda_core
ghash_clmulni_intel snd_seq mc joydev pcspkr snd_seq_device snd_pcm
sp5100_tco k10temp i2c_piix4 snd_timer thinkpad_acpi ledtrig_audio snd
wmi soundcore video i2c_scmi acpi_cpufreq ip_tables amdgpu(O)
rtsx_pci_sdmmc amd_iommu_v2 gpu_sched mmc_core i2c_algo_bit ttm
drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec drm
crc32c_intel serio_raw hid_multitouch r8152 mii nvme r8169 nvme_core
rtsx_pci pinctrl_amd
CPU: 5 PID: 1511 Comm: gnome-shell Tainted: G           O      5.5.0-rc7Lyude-Test+ #4
Hardware name: LENOVO FA495SIT26/FA495SIT26, BIOS R12ET22W(0.22 ) 01/31/2019
RIP: 0010:update_mst_stream_alloc_table+0x11e/0x130 [amdgpu]
Code: 28 00 00 00 75 2b 48 8d 65 e0 5b 41 5c 41 5d 41 5e 5d c3 0f b6 06
49 89 1c 24 41 88 44 24 08 0f b6 46 01 41 88 44 24 09 eb 93 <0f> 0b e9
2f ff ff ff e8 a6 82 a3 c2 66 0f 1f 44 00 00 0f 1f 44 00
RSP: 0018:ffffac428127f5b0 EFLAGS: 00010202
RAX: 0000000000000002 RBX: ffff8d1e166eee80 RCX: 0000000000000000
RDX: ffffac428127f668 RSI: ffff8d1e166eee80 RDI: ffffac428127f610
RBP: ffffac428127f640 R08: ffffffffc03d94a8 R09: 0000000000000000
R10: ffff8d1e24b02000 R11: ffffac428127f5b0 R12: ffff8d1e1b83d000
R13: ffff8d1e1bea0b08 R14: 0000000000000002 R15: 0000000000000002
FS:  00007fab23ffcd80(0000) GS:ffff8d1e28b40000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f151f1711e8 CR3: 00000005997c0000 CR4: 00000000003406e0
Call Trace:
 ? mutex_lock+0xe/0x30
 dc_link_allocate_mst_payload+0x9a/0x210 [amdgpu]
 ? dm_read_reg_func+0x39/0xb0 [amdgpu]
 ? core_link_enable_stream+0x656/0x730 [amdgpu]
 core_link_enable_stream+0x656/0x730 [amdgpu]
 dce110_apply_ctx_to_hw+0x58e/0x5d0 [amdgpu]
 ? dcn10_verify_allow_pstate_change_high+0x1d/0x280 [amdgpu]
 ? dcn10_wait_for_mpcc_disconnect+0x3c/0x130 [amdgpu]
 dc_commit_state+0x292/0x770 [amdgpu]
 ? add_timer+0x101/0x1f0
 ? ttm_bo_put+0x1a1/0x2f0 [ttm]
 amdgpu_dm_atomic_commit_tail+0xb59/0x1ff0 [amdgpu]
 ? amdgpu_move_blit.constprop.0+0xb8/0x1f0 [amdgpu]
 ? amdgpu_bo_move+0x16d/0x2b0 [amdgpu]
 ? ttm_bo_handle_move_mem+0x118/0x570 [ttm]
 ? ttm_bo_validate+0x134/0x150 [ttm]
 ? dm_plane_helper_prepare_fb+0x1b9/0x2a0 [amdgpu]
 ? _cond_resched+0x15/0x30
 ? wait_for_completion_timeout+0x38/0x160
 ? _cond_resched+0x15/0x30
 ? wait_for_completion_interruptible+0x33/0x190
 commit_tail+0x94/0x130 [drm_kms_helper]
 drm_atomic_helper_commit+0x113/0x140 [drm_kms_helper]
 drm_atomic_helper_set_config+0x70/0xb0 [drm_kms_helper]
 drm_mode_setcrtc+0x194/0x6a0 [drm]
 ? _cond_resched+0x15/0x30
 ? mutex_lock+0xe/0x30
 ? drm_mode_getcrtc+0x180/0x180 [drm]
 drm_ioctl_kernel+0xaa/0xf0 [drm]
 drm_ioctl+0x208/0x390 [drm]
 ? drm_mode_getcrtc+0x180/0x180 [drm]
 amdgpu_drm_ioctl+0x49/0x80 [amdgpu]
 do_vfs_ioctl+0x458/0x6d0
 ksys_ioctl+0x5e/0x90
 __x64_sys_ioctl+0x16/0x20
 do_syscall_64+0x55/0x1b0
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fab2121f87b
Code: 0f 1e fa 48 8b 05 0d 96 2c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff
ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01
f0 ff ff 73 01 c3 48 8b 0d dd 95 2c 00 f7 d8 64 89 01 48
RSP: 002b:00007ffd045f9068 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007ffd045f90a0 RCX: 00007fab2121f87b
RDX: 00007ffd045f90a0 RSI: 00000000c06864a2 RDI: 000000000000000b
RBP: 00007ffd045f90a0 R08: 0000000000000000 R09: 000055dbd2985d10
R10: 000055dbd2196280 R11: 0000000000000246 R12: 00000000c06864a2
R13: 000000000000000b R14: 0000000000000000 R15: 000055dbd2196280
---[ end trace 6ea888c24d2059cd ]---

Note as well, I have only been able to reproduce this on setups with 2
MST displays.

Changes since v1:
* Don't return false when part 1 or part 2 of updating the payloads
  fails, we don't want to abort at any step of the process even if
  things fail
Reviewed-by: NMikita Lipski <Mikita.Lipski@amd.com>
Signed-off-by: NLyude Paul <lyude@redhat.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It needed to be updated as well so it will show the proper values
if you reset to the defaults.

Bug: https://gitlab.freedesktop.org/drm/amd/issues/1020Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Cull out 0 clocks to avoid a warning in DC.

Bug: https://gitlab.freedesktop.org/drm/amd/issues/963Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Only send non-0 clocks to DC for validation.  This mirrors
what the windows driver does.

Bug: https://gitlab.freedesktop.org/drm/amd/issues/963Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We might get different numbers of clocks from powerplay depending
on what the OEM has populated.

v2: add assert for at least one level

Bug: https://gitlab.freedesktop.org/drm/amd/issues/963Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Ask the SMU for the default VDDC curve voltage values.  This
properly reports the VDDC values in the OD interface.

v2: only update if the original values are 0

Bug: https://gitlab.freedesktop.org/drm/amd/issues/1020Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.5.x

Previously, the syfs functionality for restoring the default powerplay
table was sourcing it's information from the currently-staged powerplay
table.

This patch adds a step to cache the first overdrive table that we see on
boot, so that it can be used later to "restore" the powerplay table

v2: sqaush my original with Matt's fix

Bug: https://gitlab.freedesktop.org/drm/amd/issues/1020Signed-off-by: NMatt Coffin <mcoffin13@gmail.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.5.x

So users can see the range of valid values.

Bug: https://gitlab.freedesktop.org/drm/amd/issues/1020Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.5.x

You can only adjust the max mclk, not the min.

Bug: https://gitlab.freedesktop.org/drm/amd/issues/1020Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.5.x

[Why]
When we disable a connector we don't explicitly remove it from the module so the
display is still cached(SW) in the hdcp_module.

SST: no issues because we can only have 1 display per link

MST: We have x displays per link, now if we disable 1 we don't remove it from the
module so the module has x display cached(SW).

If we try to enable HDCP, psp verification will fail because we are reporting x
displays while the HW only has x-1 display enabled

[How]
Check the callback for when we disable stream and call remove display.
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Remove a backslash symbol accidentally left in increase bpp function
when computing mst dsc configuration.
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Reviewed-by: NZhan Liu <zhan.liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This workaround is needed only for Navi10 12 Gbps SKUs.

V2: added SMU firmware version guard
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The sdma_queue_count increment should be done before
execute_queues_cpsch(), which calls pm_calc_rlib_size() where
sdma_queue_count is used to calculate whether over_subscription is
triggered.

With the previous code, when a SDMA queue is created,
compute_queue_count in pm_calc_rlib_size() is one more than the
actual compute queue number, because the queue_count has been
incremented while sdma_queue_count has not. This patch fixes that.
Signed-off-by: NYong Zhao <Yong.Zhao@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
In current code we're essentially drawing the cursor on every pipe
that contains it. This only works when the planes have the same
scaling for src to dest rect, otherwise we'll get "double cursor" where
one cursor is incorrectly filtered and offset from the real position.

[How]
Without dedicated cursor planes on DCN we require at least one pipe
that matches the scaling of the current timing.

This is an optimization and workaround for the most common case where
the top-most plane is not scaled but the bottom-most plane is scaled.

Whenever a pipe has a parent pipe in the blending tree whose recout
fully contains the current pipe we can disable the pipe.

This only applies when the pipe is actually visible of course.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

In old days, the "host-progs" syntax was used for specifying host
programs. It was renamed to the current "hostprogs-y" in 2004.

It is typically useful in scripts/Makefile because it allows Kbuild to
selectively compile host programs based on the kernel configuration.

This commit renames like follows:

  always       ->  always-y
  hostprogs-y  ->  hostprogs

So, scripts/Makefile will look like this:

  always-$(CONFIG_BUILD_BIN2C) += ...
  always-$(CONFIG_KALLSYMS)    += ...
      ...
  hostprogs := $(always-y) $(always-m)

I think this makes more sense because a host program is always a host
program, irrespective of the kernel configuration. We want to specify
which ones to compile by CONFIG options, so always-y will be handier.

The "always", "hostprogs-y", "hostprogs-m" will be kept for backward
compatibility for a while.
Signed-off-by: NMasahiro Yamada <masahiroy@kernel.org>

The OR routing logic in NVKM does not expect to receive supervisor
interrupts until the DD has provided consistent information on the
ORs it's using and the EVO/NVD assembly state to match.

The combination of changing window ownership + core channel update
during display init triggered a situation where we'd disconnect an
OR from the pad it was meant to still be driving on some systems.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

For various complicated reasons, we need to avoid sending a core update
method during display init.  Something, which we've been required to do
on GV100 and up because we've been assigning windows to heads there and
the HW is rather picky about when that's allowed.

This moves window assignment into the modesetting path at a point where
it's much safer to send our first update methods to NVDisplay.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Commit fd67e9c6 ("drm/tegra: Do not implement runtime PM") replaced
the generic runtime PM usage by a host1x bus-specific implementation in
order to work around some assumptions baked into runtime PM that are in
conflict with the requirements in the Tegra DRM driver.

Unfortunately the new runtime PM callbacks are not setup yet at the time
when the SOR driver first needs to resume the device to register the SOR
pad clock, and accesses to register will cause the system to hang.

Note that this only happens on Tegra124 and Tegra210 because those are
the only SoCs where the SOR pad clock is registered from the SOR driver.
Later generations use a SOR pad clock provided by the BPMP.

Fix this by moving the registration of the SOR pad clock after the
host1x client has been registered. That's somewhat suboptimal because
this could potentially, though it's very unlikely, cause the Tegra DRM
to be probed if the SOR happens to be the last subdevice to register,
only to be immediately removed again if the SOR pad output clock fails
to register. That's just a minor annoyance, though, and doesn't justify
implementing a workaround.

Fixes: fd67e9c6 ("drm/tegra: Do not implement runtime PM")
Signed-off-by: NThierry Reding <treding@nvidia.com>

If the driver fails to probe, make sure to disable runtime PM again.

While at it, make the cleanup code in ->remove() symmetric.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Make sure the SOR module is suspenden after we fail to register the SOR
pad output clock.
Signed-off-by: NThierry Reding <treding@nvidia.com>

In order to provide a clearer, more symmetric API for pinning and
unpinning DMA pages.  This way, pin_user_pages*() calls match up with
unpin_user_pages*() calls, and the API is a lot closer to being
self-explanatory.

Link: http://lkml.kernel.org/r/20200107224558.2362728-23-jhubbard@nvidia.comSigned-off-by: NJohn Hubbard <jhubbard@nvidia.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert drm/via to use the new pin_user_pages_fast() call, which sets
FOLL_PIN.  Setting FOLL_PIN is now required for code that requires
tracking of pinned pages, and therefore for any code that calls
put_user_page().

In partial anticipation of this work, the drm/via driver was already
calling put_user_page() instead of put_page().  Therefore, in order to
convert from the get_user_pages()/put_page() model, to the
pin_user_pages()/put_user_page() model, the only change required is to
change get_user_pages() to pin_user_pages().

Link: http://lkml.kernel.org/r/20200107224558.2362728-16-jhubbard@nvidia.comSigned-off-by: NJohn Hubbard <jhubbard@nvidia.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJérôme Glisse <jglisse@redhat.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Jan Kara <jack@suse.cz>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Doesn't seem to be used, but add it just in case.
Reviewed-by: NMatt Coffin <mcoffin13@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Clang warns:

../drivers/gpu/drm/amd/amdgpu/gfx_v9_4.c:967:35: warning: implicit
conversion from enumeration type 'enum amdgpu_ras_block' to different
enumeration type 'enum ta_ras_block' [-Wenum-conversion]
        block_info.block_id = info->head.block;
                            ~ ~~~~~~~~~~~^~~~~
1 warning generated.

Use the function added in commit 828cfa29 ("drm/amdgpu: Fix amdgpu
ras to ta enums conversion") that handles this conversion explicitly.

Fixes: 4c461d89 ("drm/amdgpu: add RAS support for the gfx block of Arcturus")
Link: https://github.com/ClangBuiltLinux/linux/issues/849Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This is an oversight from

commit 42585395
Author: Peter Rosin <peda@axentia.se>
Date:   Thu Jul 13 18:25:36 2017 +0200

    drm: radeon: remove dead code and pointless local lut storage

v2: Also remove leftover local variable.

Cc: Peter Rosin <peda@axentia.se>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NMichel Dänzer <mdaenzer@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Need to do atomic check first, then validate global state.
If not, when connecting both MST and HDMI displays and
set a bad mode via xrandr, system will hang.

[How]
Move drm_dp_mst_atomic_check() to the front of
dc_validate_global_state().
Signed-off-by: NZhan Liu <zhan.liu@amd.com>
Reviewed-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Per at least one tester this is enough magic to recover the regression
introduced for some people (but not all) in

commit b8e2b019
Author: Peter Rosin <peda@axentia.se>
Date:   Tue Jul 4 12:36:57 2017 +0200

    drm/fb-helper: factor out pseudo-palette

which for radeon had the side-effect of refactoring out a seemingly
redudant writing of the color palette.

10ms in a fairly slow modeset path feels like an acceptable form of
duct-tape, so maybe worth a shot and see what sticks.

Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=198123Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

There is a spelling mistake on the struct field name link_integiry_check,
fix this by renaming it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fixes: 240c811c ("drm/amdgpu: fix VRAM partially encroached issue in GDDR6 memory training(V2)")
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Currently we pre-allocate entities and fences for all the HW IPs on
context creation and some of which are might never be used.

This patch tries to resolve entity/fences wastage by creating entity
only when needed.

v2: allocate memory for entity and fences together
Signed-off-by: NNirmoy Das <nirmoy.das@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

In previous gfx9 parts, S_BARRIER shader instructions are implicitly
S_WAITCNT 0 instructions as well. This setting turns off that
mechanism in Arcturus and beyond. With this, shaders must follow the
ISA guide insofar as putting in explicit S_WAITCNT operations even
after an S_BARRIER.

v2: Fix patch title to list component
Signed-off-by: NJoseph Greathouse <Joseph.Greathouse@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Without relaxing this requirement, TU10x boards will fail to load without
an updated linux-firmware, and TU11x will completely fail to load because
FW isn't available yet.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This fixes an oops on TU11x GPUs where SEC2 attempts to register its falcon,
and triggers a NULL-pointer deref because ACR isn't yet supported.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The implementations for most channel types contains a map of methods to
priv registers in order to provide debugging info when a disp exception
has been raised.

This info is missing from the implementation of PIO channels as they're
rather simplistic already, however, if an exception is raised by one of
them, we'd end up triggering a NULL-pointer deref.  Not ideal...

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206299Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This is useful for debugging GPU hangs.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>