Another step towards proper locking: Rework the callback provided to
capidrv for controller state changes. This is so far attached to an
application, which would require us to hold the corresponding lock
across notification calls.

But there is no direct relation between a controller up/down event and
an application, so let's decouple them and provide a notifier call chain
for those events instead. This notifier chain is first of all used
internally. Here we request the highest priority to unsure that
housekeeping work is done before any other notifications. The chain is
exported via [un]register_capictr_notifier to our only user, capidrv, to
replace the racy and unfixable capi20_set_callback.
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This step prepares the application of proper controller locking: Push
all state changing work into the notify handler that are called by
capi_ctr_ready and capi_ctr_down, switch detach_capi_ctr to issue a
synchronous ctr_down. Also ensure that we do not go through any action
if the state did not change.
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turn the lock protecting registered capi drivers into a mutex and apply
it consistently.
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At least for our internal use, fix the misnomers that refer to a CAPI
controller as 'card'. No functional changes.
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CVS revisions dumped by all CAPI modules are meaningless today. And
that some CAPI module is loaded or removed does not necessarily deserve
a message. Just keep the message of the central module, capi.ko, drop
the rest.
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Auto-mounting the capifs during module init prevents unloading its
module. Instead, pin the filesystem as long as some NCCI node exists.
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

capifs_mnt->mnt_sb->s_root already contains what we need.
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of looking up the dentry of an NCCI node again in
capifs_free_ncci pass the pointer via the capifs user.

This patch also reduces the #ifdef mess in capi.c a bit as far as capifs
was causing it.
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When something went wrong during capifs_new_ncci, the looked up dentry
was not properly released. Neither was the allocated inode. Refactor the
function to avoid leaks.
Signed-off-by: NJan Kiszka <jan.kiszka@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stop computing the number of neighbour table settings we have by
counting the number of binary sysctls.  This behaviour was silly
and meant that we could not add another neighbour table setting
without also adding another binary sysctl.

Don't pass the binary sysctl path for neighour table entries
into neigh_sysctl_register.  These parameters are no longer
used and so are just dead code.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stop using the binary sysctl enumeartion in sysctl.h as an index into
a per interface array.  This leads to unnecessary binary sysctl number
allocation, and a fragility in data structure and implementation
because of unnecessary coupling.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the output logging messages a bit more consistent.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the output logging messages a bit more consistent.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some unlikely(netif_msg_<foo>(sky2)) tests are also
removed by this change.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert private DPRINTK macro uses to netif_<level> equivalents
Remove #define DPRINTK
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following build failure:

  CC      arch/sparc/kernel/sys_sparc32.o
In file included from include/linux/netfilter_ipv4/ip_tables.h:28,
                 from arch/sparc/kernel/sys_sparc32.c:46:
include/linux/netfilter/x_tables.h:525: error: expected declaration specifiers or ‘...’ before ‘nf_hookfn’
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Increase FTQ depth to 256 to ehnabce performance.
- Fix RV2P context corruption on 5709 when flow control is enabled.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the problem of dropping the carry when adding 2 32-bit values.
Switch to use array indexing for better readability.

Reported by and fix provided by Patrick Rabau.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unnecessary code that works around older versions of ethtool
that can pass down invalid advertisement speed values.  This old
code prevents the user from specifying multiple advertisement values.
The new code uses simple masking to mask out invalid advertisment bits.
Reported-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current water marks are too high and can cause unnecessary flow
control frames.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New status blocks are allocated during MTU change so we need to
update this information for the cnic driver.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Checking the flag is more correct than checking bp->irq_nvecs. By
accident it is not a problem because we always have more than 1
vectors when using MSIX mode.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

AR8151 is a Gigabit Ethernet device. AR8152 devices are
Fast Ethernet devices, there are two revisions, a 1.0
and a 2.0 revision.

This has been tested against these devices:

Driver	Model-name	vendor:device	Type
atl1c 	AR8131		1969:1063	Gigabit Ethernet
atl1c	AR8132		1969:1062	Fast Ethernet
atl1c	AR8151(v1.0)	1969:1073	Gigabit Ethernet
atl1c	AR8152(v1.1)	1969:2060	Fast Ethernet

This device has no hardware available yet so it goes untested,
but it should work:

atl1c	AR8152(v2.0)	1969:2062	Fast Ethernet
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Same stuff as in ip_gre patch: receive hook can be called before netns
setup is done, oopsing in net_generic().
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRE protocol receive hook can be called right after protocol addition is done.
If netns stuff is not yet initialized, we're going to oops in
net_generic().

This is remotely oopsable if ip_gre is compiled as module and packet
comes at unfortunate moment of module loading.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_ethtool() is currently using 604 bytes of stack, even with gcc-4.4.2

objdump -d vmlinux | scripts/checkstack.pl
...
0xc04bbc33 dev_ethtool [vmlinux]:			604
...
Adding noinline attributes to selected functions can reduce stack usage.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These changes add MDIO and phy lib support to the driver as the
IP core now supports the MDIO bus.

The MDIO bus and phy are added as a child to the emaclite in the device
tree as illustrated below.

mdio {
	#address-cells = <1>;
	#size-cells = <0>;
	phy0: phy@7 {
		compatible = "marvell,88e1111";
		reg = <7>;
	} ;
}
Signed-off-by: NSadanand Mutyala <Sadanand.Mutyala@xilinx.com>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Addresses should be all digits.
Stops x25_bind using addresses containing characters.
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_socket failures should return -ENOBUFS
a bad protocol should return -EINVAL
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code has been tested on IBM pSeries server.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Observed similar behavior on SPD as previouly seen on SAD flushing..
This fixes it.

cheers,
jamal
commit 428b20432dc31bc2e01a94cd451cf5a2c00d2bf4
Author: Jamal Hadi Salim <hadi@cyberus.ca>
Date:   Thu Feb 11 05:49:38 2010 -0500

    xfrm: Flushing empty SPD generates false events

    To see the effect make sure you have an empty SPD.
    On window1 "ip xfrm mon" and on window2 issue "ip xfrm policy flush"
    You get prompt back in window1 and you see the flush event on window2.
    With this fix, you still get prompt on window1 but no event on window2.
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To see the effect make sure you have an empty SAD.
-On window1 "ip xfrm mon"
-on window2 issue "ip xfrm state flush"
You get prompt back in window1
and you see the flush event on window2.
With this fix, you still get prompt on window1 but no
event on window2.

I was tempted to return -ESRCH on window1 (which would
show "RTNETLINK answers: No such process") but didnt want
to change current behavior.

cheers,
jamal
commit 5f3dd4a772326166e1bcf54acc2391df00dc7ab5
Author: Jamal Hadi Salim <hadi@cyberus.ca>
Date:   Thu Feb 11 04:41:36 2010 -0500

    xfrm: Flushing empty SAD generates false events

    To see the effect make sure you have an empty SAD.
    On window1 "ip xfrm mon" and on window2 issue "ip xfrm state flush"
    You get prompt back in window1 and you see the flush event on window2.
    With this fix, you still get prompt on window1 but no event on window2.
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When no more memory can be allocated, fq_find() will return NULL and
increase the value of IPSTATS_MIB_REASMFAILS. In this case,
ipv6_frag_rcv() also increase the value of IPSTATS_MIB_REASMFAILS.

So, the patch deletes redundant counter of IPSTATS_MIB_REASMFAILS in fq_find().
and deletes the unused parameter of idev.
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RCU usage in the original code was broken because
there are cases where we possibly sleep with rcu_read_lock
held. As a fix, change the macvtap_file_get_queue to
get a reference on the socket and the netdev instead of
taking the full rcu_read_lock.

Also, change macvtap_file_get_queue failure case to
not require a subsequent macvtap_file_put_queue, as
pointed out by Ed Swierk.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Ed Swierk <eswierk@aristanetworks.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: NSridhar Samudrala <sri@us.ibm.com>
Acked-by: NEd Swierk <eswierk@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is expected to report that the link is up
when the phy Rx signal is established and the mac
has not detected a link fault.
The code is however broken, the driver does not check the link fault
status when the phy link status changes.
The link fault status being checked within a short period of time,
it leads to link up/link down events.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mac is expected to auto-inflate the Maximum Frame size for VLAN
tagged frames. It however does not work with jumbo frames.
Work around the bug adding 4 to the Maximum Frame for MTUs
greater than 1536.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>