Pre-tunnel rules are used when the tunnel end-point is on an 'internal
port'. These rules are used to direct the tunnelled packets (based on outer
header fields) to the internal port where they can be detunnelled. The
rule must send the packet to ingress the internal port at the TC layer.

Currently FW does not support an action to send to ingress so cannot
offload such rules. However, in preparation for populating the pre-tunnel
table to represent such rules, check for rules that send to the ingress of
an internal port and mark them as such. Further validation of such rules
is left to subsequent patches.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.

Modify the NFP driver to allow the offload of MPLS set actions to
firmware. Set actions update the outermost MPLS header. The offload
includes a mask to specify which fields should be set.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.

Modify the NFP driver to allow the offload of MPLS pop actions to
firmware. The act_mpls TC module enforces that the next protocol is
supplied along with the pop action. Passing this to firmware allows it
to properly rebuild the underlying packet after the pop.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.

Modify the NFP driver to allow the offload of MPLS push actions to
firmware.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And any other existing fields in this structure that refer to tc.
Specifically:

* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new GRE encapsulation support, which allows offload of filters
using tunnel_key set action in combination with actions that egress
to GRE type ports.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously tunnel related functions in action offload only applied
to UDP tunnels. Rename these functions in preparation for new
tunnel types.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use extack messages in flower offload when compiling match and actions
messages that will configure hardware.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the introduction of flow_action_for_each pedit actions are no
longer grouped together, instead pedit actions are broken out per
32 byte word. This results in an inefficient use of the action list
that is pushed to hardware where each 32 byte word becomes its own
action. Therefore we combine groups of 32 byte word before sending
the action list to hardware.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We no longer set CFI when pushing vlan tags, therefore we remove
the CFI bit from push vlan.

Fixes: 1a1e586f ("nfp: add basic action capabilities to flower offloads")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NLouis Peens <louis.peens@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added IANA_VXLAN_UDP_PORT (4789) definition to vxlan header file so it
can be used by drivers instead of local definition.
Updated drivers which locally defined it as 4789 to use it.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Cc: John Hurley <john.hurley@netronome.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Yunsheng Lin <linyunsheng@huawei.com>
Cc: Peng Li <lipeng321@huawei.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Move the definition of the default Geneve udp port from the geneve
source to the header file, so we can re-use it from drivers.
Modify existing drivers to use it.
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Cc: John Hurley <john.hurley@netronome.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Static checker warning complains on uninitialized variable:

        drivers/net/ethernet/netronome/nfp/flower/action.c:618 nfp_fl_pedit()
        error: uninitialized symbol 'idx'.

Which is actually never used from the functions that take it as
parameter. Remove it.

Fixes: 73867881 ("drivers: net: use flow action infrastructure")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().

Since NFP uses switchdev_port_same_parent_id() convert it to use
netdev_port_same_parent_id().
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates drivers to use the new flow action infrastructure.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.

To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.

This introduces two new interfaces:

	bool flow_rule_match_key(rule, dissector_id)

that returns true if a given matching key is set on, and:

	flow_rule_match_XYZ(rule, &match);

To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both the actions and tunnel_conf files contain local functions that check
the type of an input netdev. In preparation for re-use with tunnel offload
via indirect blocks, move these to static inline functions in a header
file.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously the offload functions in NFP assumed that the ingress (or
egress) netdev passed to them was an nfp repr.

Modify the driver to permit the passing of non repr netdevs as the ingress
device for an offload rule candidate. This may include devices such as
tunnels. The driver should then base its offload decision on a combination
of ingress device and egress port for a rule.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of the recently added VXLAN and geneve helper functions to
determine the type of the netdev from its rtnl_link_ops.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ipv6 set flow label and hop limit action offload. Since pedit sets
headers per 4 byte word, we need to ensure that setting either version,
priority, payload_len or nexthdr does not get offloaded.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ipv4 set ttl and tos action offload. Since pedit sets headers per 4
byte word, we need to ensure that setting either version, ihl, protocol,
total length or checksum does not get offloaded.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously when populating the set ipv6 address action, we incorrectly
made use of pedit's key index to determine which 32bit word should be
set. We now calculate which word has been selected based on the offset
provided by the pedit action.

Fixes: 354b82bb ("nfp: add set ipv6 source and destination address")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we only allowed a single header key per pedit action to
change the header. This used to result in the last header key in the
pedit action to overwrite previous headers. We now keep track of them
and allow multiple header keys per pedit action.

Fixes: c0b1bd9a ("nfp: add set ipv4 header action flower offload")
Fixes: 354b82bb ("nfp: add set ipv6 source and destination address")
Fixes: f8b7b0a6 ("nfp: add set tcp and udp header action flower offload")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not correctly change headers when using multiple
pedit actions with partial masks. We now take this into account and
no longer just commit the last pedit action.

Fixes: c0b1bd9a ("nfp: add set ipv4 header action flower offload")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the repeated license text with SDPX identifiers.
While at it bump the Copyright dates for files we touched
this year.
Signed-off-by: NEdwin Peer <edwin.peer@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NNic Viljoen <nick.viljoen@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a bug where ipv6 tunnels would report that it is
getting offloaded to hardware but would actually be rejected
by hardware.

Fixes: b27d6a95 ("nfp: compile flower vxlan tunnel set actions")
Signed-off-by: NLouis Peens <louis.peens@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 90b73b77, list_head is no longer needed.
Now we just need to convert the list iteration to array
iteration for drivers.

Fixes: 90b73b77 ("net: sched: change action API to use array of pointers to actions")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce new push geneve option action. This allows offloading
filters configured to entunnel geneve with options.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TTL for encapsulating headers in IPv4 UDP tunnels is taken from a
route lookup. Modify this to first check if a user has specified a TTL to
be used in the TC action.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract the tos and the tunnel flags from the tunnel key and offload these
action fields. Only the checksum and tunnel key flags are implemented in
fw so reject offloads of other flags. The tunnel key flag is always
considered set in the fw so enforce that it is set in the rule. Note that
the compulsory setting of the tunnel key flag and optional setting of
checksum is inline with how tc currently generates ipv4 udp tunnel
actions.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously the ttl for ipv4 udp tunnels was set to the namespace default.
Modify this to attempt to extract the ttl from a full route lookup on the
tunnel destination. If this is not possible then resort to the default.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware will automatically update csum in headers when a set action has
been performed. This means we could in the driver ignore the explicit
checksum action when performing a set action.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the egress device of an offloaded rule is a LAG port, then encode the
output port to the NFP with a LAG identifier and the offloaded group ID.

A prelag action is also offloaded which must be the first action of the
series (although may appear after other pre-actions - e.g. tunnels). This
causes the FW to check that it has the necessary information to output to
the requested LAG port. If it does not, the packet is sent to the kernel
before any other actions are applied to it.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware requires that the ttl value for an encapsulating ipv4 tunnel
header be included as an action field. Prior to the support of Geneve
tunnel encap (when ttl set was removed completely), ttl value was
extracted from the tunnel key. However, tests have shown that this can
still produce a ttl of 0.

Fix the issue by setting the namespace default value for each new tunnel.
Follow up patch for net-next will do a full route lookup.

Fixes: 3ca3059d ("nfp: flower: compile Geneve encap actions")
Fixes: b27d6a95 ("nfp: compile flower vxlan tunnel set actions")
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Generate rules for the NFP to encapsulate packets in Geneve tunnels. Move
the vxlan action code to generic udp tunnel actions and use core code for
both vxlan and Geneve.

Only support outputting to well known port 6081. Setting tunnel options
is not supported yet.

Only attempt to offload if the fw supports Geneve.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcfm_dev always points to the correct netdev and we already
hold a refcnt, so no need to use tcfm_ifindex to lookup again.

If we would support moving target netdev across netns, using
pointer would be better than ifindex.

This also fixes dumping obsolete ifindex, now after the
target device is gone we just dump 0 as ifindex.

Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modified netronome nfp flower action to use VLAN helper functions instead
of accessing/referencing TC act_vlan private structures directly.
Reviewed-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NManish Kurup <manish.kurup@verizon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not ensure that a netdev is a representative netdev
before dereferencing its private data. This can occur when an upper netdev
is created on a representative netdev. This patch corrects this by first
ensuring that the netdev is a representative netdev before using it.
Checking only switchdev_port_same_parent_id is not sufficient to ensure
that we can safely use the netdev. Failing to check that the netdev is also
a representative netdev would result in incorrect dereferencing.

Fixes: 1a1e586f ("nfp: add basic action capabilities to flower offloads")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use direct access struct fields rather than PREP_FIELD()
macros to manipulate the jump ID and length, both of which
are exactly 8-bits wide. This simplifies the code somewhat.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not have offloading support for set TCP/UDP actions. This
patch enables TC flower offload of set TCP/UDP sport and dport actions.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>