This is preparation for adding differing implementations for new NICs.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pause frame generation is gated by both RX_XOFF_MAC_EN and an enable
bit in each MAC.  RX_XOFF_MAC_EN bit always reads back as 0 so we need
to set it correctly every time we modify RX_CFG_REG.  Simplify this by
always setting it to 1 and only changing the enable bits in the MACs.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register only needs to be written after reset, not each time we
enable interrupts.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch extends the ethtool interface to display what PHY
is currently connected to a NIC.  The results can be viewed in
ethtool ethX output.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes an issue when clearing out the RAR entries.  If RAR[0]
is the only address in use, don't clear the others.
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82598 shouldn't try and access LINKS2 while configuring
link and flow control.  This is an 82599-only register.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow Control autoneg should be disabled for certain adapters
that don't support autonegotiation of Flow Control at 10 gigabit.
These interfaces are the 10GBASE-T devices, CX4, and SFP+, all
running at 10 gigabit only.  1 gigabit is fine.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was doing a divide by zero when adjusting tx-usecs.
This patch removes the divide by zero code and changes the logic slightly
to ignore tx-usecs in the case of shared TxRx vectors.

Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert smc91x driver from legacy PM hooks over to using dev_pm_ops.

Tested on OMAP3 platform.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NNicolas Pitre <nico@fluxnic.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 'likely' hint to test of rx_checksum_enabled.
Don't count IP fragments; the IP stack can do that.
Do count non-matching multicast packets.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "bug9141 workaround" of setting TX_FLUSH_MIN_LEN_EN should really
be considered as a normal bit of configuration rather than a
workaround.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The strap bits are only important on Falcon A and all production
boards using it have fixed-speed 10G PHYs.

Replace dummy MAC operations with default MAC operations.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We never use MDIO in atomic context, so we don't need to spin.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reading standard registers on the QT2025C before its firmware has
booted may cause the boot process to fail.  Therefore, follow the
recommended reset sequence before reading its id registers.  Either
order works for the QT2022C2, so don't differentiate.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Falcon can generate events for LASI interrupts from the PHY, but in
practice we have never implemented this in reference designs.  Instead
we have polled, inserted the appropriate events, and then handled the
events later.  This is a waste of time and code.

Instead, make PHY poll functions update the link state synchronously
and report whether it changed.  We can still make use of the LASI
registers as a shortcut on the SFT9001.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Steve Hodgson <shodgson@solarflare.com>

Currently we can set multicast hash immediately (in atomic context)
but must delay setting MAC promiscuity.  There is not that much
point in deferring one but not the other, and setting the multicast
hash on Siena will involve a firmware request.  So process them
both in efx_mac_work().

Also, set the broadcast bit in the multicast hash in
efx_set_multicast_list(), since this is required for both Falcon and
Siena.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Steve Hodgson <shodgson@solarflare.com>

Only the XMAC on Falcon needs help from the driver to poll and reset
the MAC-PHY link (XAUI); GMII is a simple parallel bus and on later
NICs firmware takes care of the XAUI link.  Also, an XMAC interrupt
currently schedules a work item which simply clears a flag
(efx_nic::mac_up) to be checked by the regular monitor (or the next
link reconfiguration, if that is sooner).

Rename the flag to xmac_poll_required, changing its sense.  Remove the
needless indirection and just set the flag immediately.  Call
falcon_xmac_poll() directly where required.

Add a new generic operation mac_op::check_fault to check the link
outside of regular monitoring, as required during self-tests.

(Note that this leaves us with an unused work item, but we will
immediately have another use for it.)
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Steve Hodgson <shodgson@solarflare.com>

Currently we initiate MAC stats DMA and busy-wait for completion when
stats are requested.  We can improve on this with a periodic timer to
initiate and poll for stats, and opportunistically poll when stats are
requested.

Since efx_nic::stats_disable_count and efx_stats_{disable,enable}()
are Falcon-specific, rename them and move them accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Although efx_init_port() is only called at probe time and so cannot
race with port reconfiguration, most of the functions it calls can
expect to be called with the MAC lock held.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid overrunning the hardware limit of 4 concurrent RX queue flushes.
Expand the queue flush state to support this.  Make similar changes to
TX flushing to keep the code symmetric.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Put all static information in struct falcon_board_type and replace it
with a pointer in struct falcon_board.  Simplify probing aocordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Although all the defined fields in these registers are within 32 bits,
they are architecturally defined as 128-bit like most other Falcon
registers.  In particular, we must use efx_reado() to ensure proper
locking when reading MD_STAT_REG.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These were accidentally undersized by a factor of 2, which limited
performance.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to support all three modes of macvlan at
runtime, extend the existing netlink protocol
to allow choosing the mode per macvlan slave
interface.

This depends on a matching patch to iproute2
in order to become accessible in user land.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows each macvlan slave device to be in one
of three modes, depending on the use case:

MACVLAN_PRIVATE:
  The device never communicates with any other device
  on the same upper_dev. This even includes frames
  coming back from a reflective relay, where supported
  by the adjacent bridge.

MACVLAN_VEPA:
  The new Virtual Ethernet Port Aggregator (VEPA) mode,
  we assume that the adjacent bridge returns all frames
  where both source and destination are local to the
  macvlan port, i.e. the bridge is set up as a reflective
  relay.
  Broadcast frames coming in from the upper_dev get
  flooded to all macvlan interfaces in VEPA mode.
  We never deliver any frames locally.

MACVLAN_BRIDGE:
  We provide the behavior of a simple bridge between
  different macvlan interfaces on the same port. Frames
  from one interface to another one get delivered directly
  and are not sent out externally. Broadcast frames get
  flooded to all other bridge ports and to the external
  interface, but when they come back from a reflective
  relay, we don't deliver them again.
  Since we know all the MAC addresses, the macvlan bridge
  mode does not require learning or STP like the bridge
  module does.

Based on an earlier patch "macvlan: Reflect macvlan packets
meant for other macvlan devices" by Eric Biederman.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NPatrick McHardy <kaber@trash.net>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have very similar code for rx statistics in
two places in the macvlan driver, with a third
one being added in the next patch.

Consolidate them into one function to improve
overall readability of the driver.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>