Add a VMX optimised xor, used primarily for RAID5. On a POWER7 blade
this is a decent win:

   32regs    : 17932.800 MB/sec
   altivec   : 19724.800 MB/sec

The bigger gain is when the same test is run in SMT4 mode, as it
would if there was a lot of work going on:

   8regs     :  8377.600 MB/sec
   altivec   : 15801.600 MB/sec

I tested this against an array created without the patch, and also
verified it worked as expected on a little endian kernel.

[ Fix !CONFIG_ALTIVEC build -- BenH ]
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Correct reference to the location of the kexec_sequence() assembly helper.
There never was a kexec_stub.S in mainline.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The condition register (CR) is a 32 bit quantity so we should use
32 bit loads and stores.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Enable a few modules required to boot on a POWER multipath
box.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Run savedefconfig over the ppc64, ppc64e and pseries config
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Using -mcpu=power7 allows gcc to use a number of new instructions
including 64 bit byte reversed loads.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

commit f13c13a0 (powerpc: Stop using non-architected shared_proc
field in lppaca) fixed a potential issue with shared/dedicated
partition detection. The old method of detection relied on an
unarchitected field (shared_proc), and this patch switched
to using something architected (a non zero yield_count).

Unfortunately the assertion in the Linux header that yield_count
is only non zero on shared processor partitions is not true. It
turns out dedicated processor partitions can increment yield_count
and as such we falsely detect dedicated partitions as shared.

Fix the comment, and switch back to using the old method.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch addresses unaligned single precision floating point loads
and stores in the single-step code.  The old implementation
improperly treated an 8 byte structure as an array of two 4 byte
words, which is a classic little endian bug.
Signed-off-by: NTom Musta <tmusta@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch modifies the unaligned access routines of the sstep.c
module so that it properly reverses the bytes of storage operands
in the little endian kernel kernel.   This is implemented by
breaking an unaligned little endian access into a combination of
single byte accesses plus an overal byte reversal operation.
Signed-off-by: NTom Musta <tmusta@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch enables alignment handling for the load/store floating point
pair instructions (lfdp, lfdpx, stfdp, stfdpx).  The handler routine
is properly coded and only needs to be enabled.
Signed-off-by: NTom Musta <tmusta@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The alignment handler is incorrect for unaligned string instructions
in little endian mode.  These instructions access data as arrays of
bytes and thus are endian neutral.  However, the routine also handles
the load/store multiple instructions, which are NOT endian neutral.

This patch toggles the byte swapping flag for the string instructions
in little endian builds.  This effectively disables the byte swapping
logic.
Signed-off-by: NTom Musta <tmusta@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This issue was causing the QEMU emulated USB device to fail dring
PCI probe.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit e82b89a6 used strcat instead of
strcpy which can result in an overflow of newlines on the buffer.

Signed-off-by: Prarit Bhargava
Cc: benh@kernel.crashing.org
Cc: ben@decadent.org.uk
Cc: stable@vger.kernel.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

PPC44x supports page sizes other than 4K however when 64K page sizes
are selected compilation fails. This is due to a change in the
definition of pgtable_t introduced by the following patch:

commit 5c1f6ee9
Author: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
powerpc: Reduce PTE table memory wastage

The above patch only implements the new layout for PPC64 so it doesn't
compile for PPC32 with a 64K page size. Ideally we should implement
the same layout for PPC32 however for the meantime this patch reverts
the definition of pgtable_t for PPC32.
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If you try and build the FA_DUMP code with CONFIG_KEXEC=n, you see
errors such as the following:

arch/powerpc/kernel/fadump.c
  408:2: error: 'crashing_cpu' undeclared (first use in this function)
  410:2: error: implicit declaration of function 'crash_save_vmcoreinfo'
  513:22: error: storage size of 'prstatus' isn't known
  520:2: error: implicit declaration of function 'elf_core_copy_kernel_regs'
  521:36: error: 'KEXEC_CORE_NOTE_NAME' undeclared (first use in this function)
  624:49: error: 'note_buf_t' undeclared (first use in this function)
  872:2: error: implicit declaration of function 'paddr_vmcoreinfo_note'
  874:18: error: 'vmcoreinfo_max_size' undeclared (first use in this function)

This is because although FA_DUMP doesn't use kexec as the actual reboot
mechanism, it does use parts of the kexec code to assemble/disassemble
the crash image.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This patch fixes typo in comments virtual to physical
address conversion.
Signed-off-by: NVaishnavi Bhat <vaishnavi@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Move the few declarations from arch/powerpc/kernel/setup.h
into arch/powerpc/include/asm/setup.h.  This resolves a
sparse warning for arch/powerpc/mm/numa.c which defines
do_init_bootmem() but can't include the setup.h header
in the prior path.

Resolves:
arch/powerpc/mm/numa.c:998:13:
        warning: symbol 'do_init_bootmem' was not declared.
                 Should it be static?
Signed-off-by: NRobert C Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Simple fixes for sparse warnings in this file.

Resolves:
arch/powerpc/mm/numa.c:198:24:
        warning: Using plain integer as NULL pointer

arch/powerpc/mm/numa.c:1157:5:
       warning: symbol 'hot_add_node_scn_to_nid' was not declared.
                Should it be static?

arch/powerpc/mm/numa.c:1238:28:
       warning: Using plain integer as NULL pointer

arch/powerpc/mm/numa.c:1538:6:
       warning: symbol 'topology_schedule_update' was not declared.
                Should it be static?
Signed-off-by: NRobert C Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit c55aef0e ("powerpc/boot: Change the load address for the
wrapper to fit the kernel") adjusts the wrapper address unnecessarily
for platforms that use arch/powerpc/boot/of.c, since the code there
allocates space for the kernel wherever it can find it and doesn't
necessarily load the kernel at address 0.  Changing the link address
is actually harmful since it can cause the zImage to overlap with
Open Firmware and thus fail to boot.

To fix this, we set make_space to n for all of the platforms that
use of.o.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Caused by commit a4da0d50 ("powerpc: Implement
arch_get_random_long/int() for powernv") from the powerpc tree
interacting with commit b5b4bb3f ("of: only include prom.h on sparc")
from the dt-rh tree.

I added this merge fix patch (which will need to be sent to Linus when
these two trees get merged, or could be applied now to the powerpc tree):

[ Also add linux/smp.h to get cpu_to_chip_id -- BenH ]
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Highlights include corenet board file consolidation, the ability to run
userspaces with lwsync on e500v1/v2, some cleanup patches that other KVM
patches will build on, support for stripped-down e6500 emulation targets,
and some fixes of minor longstanding issues.

Add Paul's fix for 32-bit register corruption in the new FP code

Commit 9863c28a ("powerpc: Emulate sync
instruction variants") introduced a build breakage with
CONFIG_PPC_EMULATED_STATS enabled.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Cc: Kumar Gala <galak@kernel.org>
Cc: James Yang <James.Yang@freescale.com>
---

During "make ppc6xx_defconfig" the following happens:

  HOSTCC  scripts/basic/fixdep
  GEN     /usr/local/src/tmp/lnx/Makefile
  HOSTCC  scripts/kconfig/conf.o
  HOSTCC  scripts/kconfig/zconf.tab.o
  HOSTLD  scripts/kconfig/conf
arch/powerpc/configs/ppc6xx_defconfig:74:warning: symbol value 'm' invalid for MCU_MPC8349EMITX

Setting CONFIG_MCU_MPC8349EMITX=y in ppc6xx_defconfig makes the warning
go away. This too has been reported by Geert Uytterhoeven a long time ago:
https://lkml.org/lkml/2011/11/13/11  - I only came across this because I
needed a "clean" defconfig for this Powerbook G5.
Signed-off-by: NChristian Kujau <lists@nerdbynature.de>
[scottwood@freescale.com: cleaned up commit message slightly]
Signed-off-by: NScott Wood <scottwood@freescale.com>

In case of error, the function platform_device_register_simple() returns
RR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NScott Wood <scottwood@freescale.com>

The P1010RDB-PB is similar to P1010RDB(P1010RDB-PA).
So, P1010RDB-PB use the same platform file as P1010RDB.
Then Add support for P1010RDB-PB platform.
Signed-off-by: NZhao Qiang <B45475@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit or error. This is obsolete meanwhile, the core will do it.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Add the missing iounmap() before return from hlwd_pic_init()
in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Activating CONFIG_PIN_TLB allows access to the 24 first Mbytes of
memory at bootup instead of 8.  It is needed for "big" kernels for
instance when activating CONFIG_LOCKDEP_SUPPORT.  This needs to be
taken into account in init_32 too, otherwise memory allocation soon
fails after startup.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Acked-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Activating CONFIG_PIN_TLB is supposed to pin the IMMR and the first
three 8Mbytes pages.  But the setting of MD_CTR to a pinnable entry was
missing before the pinning of the third 8Mb page.  As the index is
decremented module 28 (MD_RSV4D is set) after every DTLB update, the
third 8Mbytes page was not pinned.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Currently all these boards use the same machine struct and also select
the same kernel options, so it seems a bit of redundant to keep one
separate kernel option for each board. Also update the defconfigs
according to this change.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

This file is also used by some RDB and QDS boards. So the name seems
not so accurate. Rename it to corenet_generic.c. Also update the
function names in this file according to the change.
Signed-off-by: NKevin Hao <haokexin@gmail.com>

In the current kernel, the board files for p2041rdb, p3041ds, p4080ds,
p5020ds, p5040ds, t4240qds and b4qds are almost the same except the
machine name. So this introduces a cornet_generic machine to support
all these boards to avoid the code duplication.

With these changes the file corenet_ds.h becomes useless. Just delete
it.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

C290PCIe has NAND flash present on IFC Chip Select(CS) 1.

So Add "ranges" field for NAND flash on CS1.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

B4860EMU is a emualtor target with minimum peripherals. It is based on
B4860QDS and trimmed down most peripherals due to either not modeled or
lack of board level connections. The main purpose of this minimum dts is
to speed up booting on emulator.
Signed-off-by: NYork Sun <yorksun@freescale.com>
[scottwood@freescale.com: whitespace fix]
Signed-off-by: NScott Wood <scottwood@freescale.com>

T4240EMU is an emulator target with minimum peripherals. It is based on
T4240QDS and trimmed down most peripherals due to either not modeled or
lack of board level connections. The main purpose of this minimum dts is
to speed up booting on emulator.
Signed-off-by: NYork Sun <yorksun@freescale.com>
[scottwood@freescale.com: whitespace fixes]
Signed-off-by: NScott Wood <scottwood@freescale.com>

Commit 9837b43c ("powerpc/85xx: enable
coreint for all the 64bit boards") removed the ifdef that avoided
coreint on 64-bit, but it missed b4_qds.c.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Cc: Kevin Hao <haokexin@gmail.com>
Cc: Shaveta Leekha <shaveta@freescale.com>

The commit e0908085 ("powerpc/8xx: Fix
regression introduced by cache coherency rewrite") is not needed
anymore.  The issue was because dcbst wrongly sets the store bit when
causing a DTLB error, but this is now fixed by commit
0a2ab51f ("powerpc/8xx: Fixup DAR from
buggy dcbX instructions.") which handles the buggy dcbx instructions on
data page faults on the 8xx.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
[scottwood@freescale.com: fix commit message]
Signed-off-by: NScott Wood <scottwood@freescale.com>