This reverts commit e0c07557.

Jörg Otte reported his 8168evl to fail boot time link detection.

Hayes suggests reverting it for the time being.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jörg Otte <jrg.otte@gmail.com>

Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.

VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Spotted-by: NTimo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was introduced in commit 6dccd16b "r8169: merge with version
6.001.00 of Realtek's r8169 driver". I did not find the version
6.001.00 online, but in 6.002.00 or any later r8169 from Realtek
this hunk is no longer present.

Also commit 05af2142 "r8169: fix Ethernet Hangup for RTL8110SC
rev d" claims to have fixed this issue otherwise.

The magic compare mask of 0xfffe000 is dubious as it masks
parts of the Reserved part, and parts of the VLAN tag. But this
does not make much sense as the VLAN tag parts are perfectly
valid there. In matter of fact this seems to be triggered with
any VLAN tagged packet as RxVlanTag bit is matched. I would
suspect 0xfffe0000 was intended to test reserved part only.

Finally, this hunk is evil as it can cause more packets to be
handled than what was NAPI quota causing net/core/dev.c:
net_rx_action(): WARN_ON_ONCE(work > weight) to trigger, and
mess up the NAPI state causing device to hang.

As result, any system using VLANs and having high receive
traffic (so that NAPI poll budget limits rtl_rx) would result
in device hang.
Signed-off-by: NTimo Teräs <timo.teras@iki.fi>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit:  cb64edb6 upstream

Above commit may introduce a race between cp_interrupt and dev_close
/ change MTU / dev_open up state. Changes cp_interrupt to tolerate
this.  Change spin_locking in cp_interrupt to avoid possible
but unobserved race.
Reported-by: N"Francois Romieu" <romieu@fr.zoreil.com>

Tested on virtual hardware, Tx MTU size up to 4096, max tx payload
    was ping -s 4068 for MTU of 4096. No real hardware, need test
    assist.
Signed-off-by: N"John Greene" <jogreene@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "David Woodhouse" <David.Woodhouse@intel.com>
Tested-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GigaMAC registers have been reported left unitialized in several
situations:
- after cold boot from power-off state
- after S3 resume

Tweaking rtl_hw_phy_config takes care of both.

This patch removes an excess entry (",") at the end of the exgmac_reg
array as well.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NWang YanQing <udknight@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The 8139cp driver has a change_mtu function that has not been
enabled since the dawn of the git repository. However, the
generic eth_change_mtu is not used in its place, so that
invalid MTU values can be set on the interface.

Original patch salvages the broken code for the single case of
setting the MTU while the interface is down, which is safe
and also includes the range check.  Now enhanced to support up
or down interface.

v2: fix case where rxbufsz isn't changed in the up state case

Original patch from
http://lkml.indiana.edu/hypermail/linux/kernel/1202.2/00770.html

Testing: has been test on virtual 8139cp setup without issue,
have no access real hardware 8139cp, need testing help.
Signed-off-by: N"John Greene" <jogreene@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cp_open
[...]
        rc = cp_alloc_rings(cp);
        if (rc)
                return rc;

cp_alloc_rings
[...]
        mem = dma_alloc_coherent(&cp->pdev->dev, CP_RING_BYTES,
                                 &cp->ring_dma, GFP_KERNEL);

- cp_alloc_rings never frees the coherent mapping it allocates
- neither do cp_open when cp_alloc_rings fails
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recovery doesn't work too well if we leave interrupts disabled...
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for byte queue limits on RTL8139C+

Tested on real hardware.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Acked-By: NDave Täht <dave.taht@bufferbloat.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes (for me) a regression introduced by commit b01af457 ("8139cp:
set ring address before enabling receiver"). That commit configured the
descriptor ring addresses earlier in the initialisation sequence, in
order to avoid the possibility of triggering stray DMA before the
correct address had been set up.

Unfortunately, it seems that the hardware will scribble garbage into the
TxRingAddr registers when we enable "plus mode" Tx in the CpCmd
register. Observed on a Traverse Geos router board.

To deal with this, while not reintroducing the problem which led to the
original commit, we augment cp_start_hw() to write to the CpCmd register
*first*, then set the descriptor ring addresses, and then finally to
enable Rx and Tx in the original 8139 Cmd register. The datasheet
actually indicates that we should enable Tx/Rx in the Cmd register
*before* configuring the descriptor addresses, but that would appear to
re-introduce the problem that the offending commit b01af457 was trying
to solve. And this variant appears to work fine on real hardware.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit b26623da.

This reverts the revert, in net-next we'll try another scheme
to fix this bug using patches from David Woodhouse.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reverts b01af457.

The original patch was tested with emulated hardware. Real
hardware chokes.

Fixes https://bugzilla.kernel.org/show_bug.cgi?id=47041Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since eab6d18d (vlan: Don't check for vlan group before
vlan_tx_tag_present.) we don't check tp->vlgrp and thus
tp is not needed in this function.
Signed-off-by: NKirill Smelkov <kirr@mns.spb.ru>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NDayanidhi Sreenivasan <dayanidhi.sreenivasan@gmail.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

The following chips need to enable internal settings to let ASPM
and clock request work.

RTL8111E-VL, RTL8111F, RTL8411, RTL8111G
RTL8105, RTL8402, RTL8106
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Building atp.o triggers this GCC warning:
    drivers/net/ethernet/realtek/atp.c: In function ‘set_rx_mode’:
    drivers/net/ethernet/realtek/atp.c:871:26: warning: ‘mc_filter[0]’ may be used uninitialized in this function [-Wuninitialized]

GCC is correct. In promiscuous mode 'mc_filter' will be used
uninitialized in set_rx_mode_8012(), which is apparently inlined into
set_rx_mode().

But it turns out set_rx_mode_8012() will never be called, since
net_local.chip_type will always be RTL8002. So we can just remove
set_rx_mode_8012() and do some related cleanups.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL_GIGA_MAC_VER_35 includes no multicast hardware filter.
Signed-off-by: NNathan Walp <faceprint@faceprint.com>
Suggested-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This regression was spotted between Debian squeeze and Debian wheezy
kernels (respectively based on 2.6.32 and 3.2). More info about
Wake-on-LAN issues with Realtek's 816x chipsets can be found in the
following thread: http://marc.info/?t=132079219400004

Probable regression from d4ed95d7;
more chipsets are likely affected.

Tested on top of a 3.2.23 kernel.
Reported-by: NFlorent Fourcot <florent.fourcot@enst-bretagne.fr>
Tested-by: NFlorent Fourcot <florent.fourcot@enst-bretagne.fr>
Hinted-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NCyril Brulebois <kibi@debian.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After d58d46b5 (r8169: jumbo fixes.) max frame len is stored in
rtl_chip_infos[].jumbo_max for each chip and SafeMtu should be gone.
Signed-off-by: NKirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use the module_pci_driver macro to make the code simpler
by eliminating the module_init and module_exit calls
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable ALDPS function to save power when link down. Note that the
feature should be set after the other PHY settings. And the firmware
is necessary. Don't enable it without loading the firmware.

None of the firmware-free chipsets support ALDPS. Neither do the
RTL8168d/8111d.

For 8136 series, make sure the ALDPS is disabled before loading the
firmware. For 8168 series, the ALDPS would be disabled automatically
when loading firmware. You must not disable it directly.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current GRO can hold packets in gro_list for almost unlimited
time, in case napi->poll() handler consumes its budget over and over.

In this case, napi_complete()/napi_gro_flush() are not called.

Another problem is that gro_list is flushed in non friendly way :
We scan the list and complete packets in the reverse order.
(youngest packets first, oldest packets last)
This defeats priorities that sender could have cooked.

Since GRO currently only store TCP packets, we dont really notice the
bug because of retransmits, but this behavior can add unexpected
latencies, particularly on mice flows clamped by elephant flows.

This patch makes sure no packet can stay more than 1 ms in queue, and
only in stress situations.

It also complete packets in the right order to minimize latencies.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The r8169 driver currently limits the DMA burst for TX to 1024 bytes. I have
a box where this prevents the interface from using the gigabit line to its full
potential. This patch solves the problem by setting TX_DMA_BURST to unlimited.

The box has an ASRock B75M motherboard with on-board RTL8168evl/8111evl
(XID 0c900880). TSO is enabled.

I used netperf (TCP_STREAM test) to measure the dependency of TX throughput
on MTU. I did it for three different values of TX_DMA_BURST ('5'=512, '6'=1024,
'7'=unlimited). This chart shows the results:
http://michich.fedorapeople.org/r8169/r8169-effects-of-TX_DMA_BURST.png

Interesting points:
 - With the current DMA burst limit (1024):
   - at the default MTU=1500 I get only 842 Mbit/s.
   - when going from small MTU, the performance rises monotonically with
     increasing MTU only up to a peak at MTU=1076 (908 MBit/s). Then there's
     a sudden drop to 762 MBit/s from which the throughput rises monotonically
     again with further MTU increases.
 - With a smaller DMA burst limit (512):
   - there's a similar peak at MTU=1076 and another one at MTU=564.
 - With unlimited DMA burst:
   - at the default MTU=1500 I get nice 940 Mbit/s.
   - the throughput rises monotonically with increasing MTU with no strange
     peaks.

Notice that the peaks occur at MTU sizes that are multiples of the DMA burst
limit plus 52. Why 52? Because:
  20 (IP header) + 20 (TCP header) + 12 (TCP options) = 52

The Realtek-provided r8168 driver (v8.032.00) uses unlimited TX DMA burst too,
except for CFG_METHOD_1 where the TX DMA burst is set to 512 bytes.
CFG_METHOD_1 appears to be the oldest MAC version of "RTL8168B/8111B",
i.e. RTL_GIGA_MAC_VER_11 in r8169. Not sure if this MAC version really needs
the smaller burst limit, or if any other versions have similar requirements.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This one includes a 8168. Not to be confused with the sky2 driven
one whose PCI vendor and device ID are the same.
Reported-by: NNeyuki Inaya <in@joblog.ru>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, when we turned on the "Enable No Snoop Bit," we cleared all
the other Device Control bits, including error reporting enables,
Max_Payload_Size, Max_Read_Request_Size, etc.  This patch preserves
all the other bits.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Use PCI Express Capability access functions to simplify r8169 driver.
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

This reverts commit 036dafa2.

First it appears in bisection, then reverting it solves the usual
netdev watchdog problem for different people. I don't have a proper
fix yet so get rid of it.
Bisected-and-reported-by: NAlex Villacís Lasso <a_villacis@palosanto.com>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>

It is not needed for mac_ocp_{write / read}. Actually bit 31 of OCPDR
does not change and r8168_mac_ocp_read always returns ~0.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Tested-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NHayes Wang <hayeswang@realtek.com>

For RTL8111G, the settings of phy and firmware are replaced with
ocp functions. r8168g_mdio_{write / read} redirects the relative
settings to suitable ocp functions. A per-device variable is needed
to evaluate the real address of ocp functions.
rtl_writephy(tp, 0x1f, xxxx) is dedicated to keeping said variable
up-to-date.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

Twelve functions can fail silently. Now they have a chance to complain.

Macro and pasting abuse has been kept at a level where tags and
friends should not be hurt.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Further changes need more context down in the call stack.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

The 8168evl (RTL_GIGA_MAC_VER_34) based Gigabyte GA-990FXA motherboards
are very prone to NETDEV watchdog problems without this change. See
https://bugzilla.kernel.org/show_bug.cgi?id=42899 for instance.

I don't know why it *works*. It's depressingly effective though.

For the record:
- the problem may go along IOMMU (AMD-Vi) errors but it really looks
  like a red herring.
- the patch sets the RX_MULTI_EN bit. If the 8168c doc is any guide,
  the chipset now fetches several Rx descriptors at a time.
- long ago the driver ignored the RX_MULTI_EN bit.
  e542a226 changed the RxConfig
  settings. Whatever the problem it's now labeled a regression.
- Realtek's own driver can identify two different 8168evl devices
  (CFG_METHOD_16 and CFG_METHOD_17) where the r8169 driver only
  sees one. It sucks.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>