Otherwise we print out spurious processes on unused rings in the error
state.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

For reasons I can't claim to fully understand gen4 seems to require
backlight duty cycle setting after the backlight has been enabled, or
else black screen follows. I don't have documentation for the correct
sequence on gen4 either. Confirmed on Dell Latitude D630 and MacBook4,1.

This fixes a regression introduced by
commit b35684b8
Author: Jani Nikula <jani.nikula@intel.com>
Date:   Thu Nov 14 12:13:41 2013 +0200

    drm/i915: do full backlight setup at enable time

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75791
Reported-and-tested-by: mcy@lm7.fr
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79423Reported-and-tested-by: NMarc Milgram <mmilgram@redhat.com>
Cc: Stable <stable@vger.kernel.org> # 3.14+
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

On certain platforms pixel_multiplier is read out in
.get_pipe_config(), but it also gets used to calculate the
pixel clock in intel_sdvo_get_config(). If the pipe is disable
but some SDVO outputs are active, we may end up dividing by zero
in intel_sdvo_get_config().

To avoid the problem simply check for zero pixel_multiplier and skip
the division. Another attempt at fixing this involved populating
pixel_multiplier to 1 even for disabled pipes, but that triggered a
WARN because SDVO_CMD_GET_CLOCK_RATE_MULT command failed and thus
encoder_pixel_multiplier was left at zero and didn't match
pipe_config->pixel_multiplier.

The "divide by pixel_multiplier" operation got introduced here:
 commit 18442d08
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Fri Sep 13 16:00:08 2013 +0300

    drm/i915: Fix port_clock and adjusted_mode.clock readout all over

and it has caused a regression on certain machines since they would
hit the div-by-zero during resume.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76520
Cc: <stable@vger.kernel.org> # 3.13+
Tested-by: NTim Richardson <tim@tim-richardson.net>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

It causes black screen on bootup and is approximately 100x slower than
running with FBC disabled, so the GPU runs at a high frequency for much
longer - completely contrary to the power saving claims. It also still
has mutex deadlocks in multi-head scenarios, which can lead to a
system/X lockup. These bugs were known before FBC was enabled by default
on Haswell and still have not been fixed.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79716Reported-and-tested-by: NJon Kristensen <info@jonkri.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
[Jani: update subject to reflect the actual change]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Merge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-next

display rework fixes lots of displayport issues.

* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (43 commits)
  drm/nouveau/disp/dp: fix tmds passthrough on dp connector
  drm/nouveau/dp: probe dpcd to determine connectedness
  drm/nv50-: trigger update after all connectors disabled
  drm/nv50-: prepare for attaching a SOR to multiple heads
  drm/gf119-/disp: fix debug output on update failure
  drm/nouveau/disp/dp: make use of postcursor when its available
  drm/g94-/disp/dp: take max pullup value across all lanes
  drm/nouveau/bios/dp: parse lane postcursor data
  drm/nouveau/dp: fix support for dpms
  drm/nouveau: register a drm_dp_aux channel for each dp connector
  drm/g94-/disp: add method to power-off dp lanes
  drm/nouveau/disp/dp: maintain link in response to hpd signal
  drm/g94-/disp: bash and wait for something after changing lane power regs
  drm/nouveau/disp/dp: split link config/power into two steps
  drm/nv50/disp: train PIOR-attached DP from second supervisor
  drm/nouveau/disp/dp: make use of existing output data for link training
  drm/gf119/disp: start removing direct vbios parsing from supervisor
  drm/nv50/disp: start removing direct vbios parsing from supervisor
  drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
  drm/nouveau/disp/dp: create subclass for dp outputs
  ...

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We were sending the necessary state changes to unset the mode, but
never actually hit the big GO button unless another modeset happens
afterwards.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

And at the same time, obey the spec better wrt out-of-range requests.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

SOR_PWR has no effect to power-off DP links, unlike other SOR protocols.

Instead, on the source side, we cut power to the lanes after having put
the sink into D3.  Link training takes care of everything required to
bring it back again.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This previously worked for the most part due to userspace doing a
modeset in response to HPD interrupts.  This will allow us to
properly handle cases where sync is lost for other reasons, or if
userspace isn't caring.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Some kind of update?  Needed to make the power-down take effect at least.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We want to be able to power down the lanes for DPMS off.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Same place as for SOR, between detach and attach phases.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This will, at some point, be used to replace various bits and pieces of
code doing direct bios parsing.  For now, it'll just be used for some
DP improvements.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

There's also provisions to allow a pad to be locked with a specific
routing, for an indefinite period of time.  This will be used in
future patches.

The G94+ pad driver will now also power-down pads when not required.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This was a half-finished hack before, just enough to handle the shared
aux/i2c pad thing on G94 and up.

We got lucky with locking etc up until now, as this was (generally) all
protected by the DRM mode_config lock.  It's about to become a lot more
likely to hit the races.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>