The adaptive ITR (interrupt throttle rate) algorithm was adjusting
the hardware's interrupt rate too frequently.  This caused a lot
of variation in the interrupt rate for fairly constant workloads.

Change the code to have a counter and adjust only once every N
number of interrupts.

Change-ID: I0460f1f86571037484eca5aca36ac4d889cb8389
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The dynamic algorithm, while now working, doesn't have good
performance in 40G mode.

One part of this patch addresses the high CPU utilization of some small
streaming workloads that the driver should reduce CPU in.

It also changes the minimum ITR that the dynamic algorithm
will settle on, causing our minimum latency to go from 12us
to about 14us, when using adaptive mode.

It also changes the BULK interrupt rate to allow maximum throughput
on a 40Gb connection with a single thread of transmit, clamping
interrupt rate to 8000 for TX makes single thread traffic go too
slow.

The new ULTRA bulk setting is introduced and is used
when the Rx packet rate on this queue exceeds 40000 packets per
second.  This value of 40000 was chosen because the automatic tuning
of minimum ITR=20us means that a single queue can't quite achieve
that many packets per second from a round-robin test.

Change-ID: Icce8faa128688ca5fd2c4229bdd9726877a92ea2
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was using a value expressed in 2us increments
for the divisor to figure out our bytes/usec values.

Fix the usecs variable to contain a value in microseconds.

Change-ID: I5c20493103c295d6f201947bb908add7040b7c41
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change moves a multi-line register setting into a function
which simplifies reading the flow of the enable function.

This also fixes a bug where the enable function was enabling
the interrupt twice while trying to update the two interrupt
throttle rate thresholds for Rx and Tx.

Change-ID: Ie308f9d0d48540204590cb9d7a5a7b1196f959bb
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e_intr and i40e/i40evf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.

They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Acquire NVM, before issuing an AQ read nvm command for X722.
We need to acquire the NVM before issuing an AQ read to the NVM
otherwise we will get EBUSY from the FW. Also release when done.

This fixes the two X722 issues with respect to eeprom checksum verify
and reading NVM version info.

With this patch in place, i40e driver will provide basic support
for X722 devices.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces a spinlock which is to be used for synchronizing
access to VSI's MAC filter list.

This patch also synchronizes execution of other codepaths which are
accessing VSI's MAC filter list with execution of
service_task:sync_vsi_filters.

In function i40e_add_vsi, copied out LAA MAC address instead of cloning
MAC filter entry because only MAC address is needed to remove MAC VLAN
filter from FW/HW.

Change-ID: I0e10ac7c715d44aa994239642aa4d57c998573a2
Signed-off-by: NKiran Patil <kiran.patil@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump.

Change-ID: I7ec818a507554648675b9b245ced9e6b6bd9ed4e
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With 64 VFs, we can easily overwhelm the AQ on the PF if we have too low
a limit on the number of AQ requests. This leads to ARQ overflow errors,
and occasionally VFs that fail to initialize.

Since we really only hit this condition on initial VF driver load, the
requests that we process are lightweight, so this extra work doesn't
cause problems for the PF driver.

Change-ID: I620221520d8af987df6ace9ba938ffaf22107681
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

1000Base_T_Optical got added to the function that figures out what
is supported when link is down but not when link is up. Add it in there
too so that we display the correct information.

Change-ID: I85ebcdfa7c02d898c44c673b1500552a53c8042e
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the number of invalid messages from a VF is exceeded, the VF
will be disabled, due to the invalid messages.  This happens if
other VF drivers (like DPDK) send a message through the driver's
mailbox (aka virtchannel) interface, but the message is not
supported by the i40e pf driver, such as CONFIG_PROMISCUOUS_MODE.

This patch changes the num_invalid_msgs in struct i40e_vf to record
the continuous invalid msgs, and it will be reset when a valid msg
is received.

Change-ID: Iaec42fd3dcdd281476b3518be23261dd46fc3718
Signed-off-by: NJingjing Wu <jingjing.wu@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver.  This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.

The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.

The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above

Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.

Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adds support for setting a new bit in the Set Local LLDP MIB AQ command
Type field.  When set to 1, the bit indicates to FW that Apps should be
treated as non-willing.  When 0, FW behaves as before.

Change-ID: I0d2101c1606c59c7188d3e6a0c7810e0f205233a
Signed-off-by: NGreg Bowers <gregory.j.bowers@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an ethtool priv flag to enable and disable printing
the VEB statistics.

Change-ID: I7654054a3a73b08aa8310d94ee8fce6219107dd8
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Two defines that are not used are causing customer confusion - remove
them.

Change-ID: Icef0325aca8e0f4fcdfc519e026bdd375e791200
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow the nvmupdate application to decide when a read or write error
should be exposed to the user.  Since the application needs to use
write probes to find the ReadOnly sections on a potentially unknown NVM
version in the HW and read probes to check the status of the last write,
some error messages are expected, but need not be shown to the users.
The driver doesn't know which are ignorable from real errors, so needs
to let the application make the decision.

Change-ID: I78fca8ab672bede11c10c820b83c26adfd536d03
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add const to functions that return strings that aren't going to be
modified. This addresses some reported compile complaints.

Change-ID: Ic56b1e814ab4d23a50480e7fdec652445f776ee8
Signed-off-by: NJingjing Wu <jingjing.wu@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Cut down on the number of startup log entries by putting a couple behind
debug flags and combining a couple others into a single line.

Change-ID: I708089f086308f84d43f8b6f0e8a634a02d058fb
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As per Eric Dumazet's previous patches:
(see commit (24d2e4a5) - tg3: use napi_complete_done())

Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout

GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>

Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
				rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS

igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result:  941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589

Alignment      Offset         Bytes    Bytes       Recvs   Bytes    Sends
Local  Remote  Local  Remote  Xfered   Per                 Per
Recv   Send    Recv   Send             Recv (avg)          Send (avg)
    8       8      0       0 1176930056  1475.36    797726   16384.00  71905

MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result:  941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763

Alignment      Offset         Bytes    Bytes       Recvs   Bytes    Sends
Local  Remote  Local  Remote  Xfered   Per                 Per
Recv   Send    Recv   Send             Recv (avg)          Send (avg)
    8       8      0       0 1175182320  50476.00     23282   16384.00  71816

i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.

Other drivers were only compile tested.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.

In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The polling routine for i40e was rounding up the budget for Rx cleanup to
1.  This is incorrect as the netpoll poll call is expecting no Rx to be
processed as the budget passed was 0.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().

v2: removed unused variable
v3: removed another unused variable
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump.

Change-ID: I8d9a99f320af43960deba8718eee2d6de50eaf46
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Save a little stack space and remove unnecessary strncpy() with a little
string pointer.

Change-ID: Id2719d34710bfc273d3bb445fec085cd04276e88
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X722 will report Gen 1x1 in the PCI config space as it is on
IOSF bus, so skip the PCI bus link/speed check.

Change-ID: Icd5f5751dc7fb00dccf0d5dc5a0a644948e7062e
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Store off reported PHY capabilities in link_info structure.

Change-ID: Ife0f037c26983ca985dbf79abf33f8f8791369e8
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove a variable declaration inside an if block hiding an existing
declaration at the start of the function.

Also remove a forward function declaration that is no longer needed due
to code re-organization.

Change-ID: I12954668b722718074949c93d74cd20eaacd93e4
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since the flow-director-atr priv flag was added to our ethtool interface,
we don't need the on/off control in debugfs.

Change-ID: Ib3b599916434ab30ccd40074e71d7a81609b5bb5
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Even though the device might be in MFP mode, if there's only one partition
enabled, then we still have plenty of interrupts for managing the Flow
Directory Sideband activity.  This patch enables FD SB in this case.
This patch also reverses the sense of the conditional in order to remove
the negative logic.

Change-ID: I9edf211a6219fc8d159b4be9964f9fd7f4e00bc0
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This version check only applies to very, very old firmware,
that only ran on A0 hardware, which we never shipped and don't
support in this driver anyway. Remove it, before somebody
gets hurt.

Change-ID: I3752d090ff488acf98ee76b075af961e9c968ee4
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X722 has a way to work around the descriptor WB issue,
this offload helps turn that feature on.

Change-ID: I7ffa67622426bfca5a651417b63e3afcfeb60412
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Only the X722 device now supports 100M SGMII, and nothing supports
100M on 1000Base_T.

Change-ID: I6f44dcd818944edd40041410e6de380f4a359a0c
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are several error messages that have been printing when there is
no functional issue. These messages should be available at debug message
level only.

Change-ID: Id91e47bf942c483563995f30d8705fa53acd5aa3
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some customers wish to be able to control our hardware specific
feature called flow director, at runtime.  This patch enables
ethtool priv flags to control this driver/hardware specific feature.

ethtool --set-priv-flags ethX flow-director-atr off

NOTE: the ethtool ntuple interface controls the flow-director
      sideband rules.

Change-ID: Iba156350b07fa2ce66f53ded51739f9a3781fe0e
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add nlflags to the function comment for ndo_bridge_setlink.

Change-ID: I34c704f307f2a3f7bac3ca4b44e2a094d3d082d6
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump.

Change-ID: If3cd42f6c1b9546beed60faf9c79faab35216f58
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove unused members in the PHY structure and add a new member to store
all the capabilities the PHY has as reported by the FW. This information
will help us determine what speeds the device is capable of when link is
down.

Also add an enum to decode the PHY types the NVM is capable of.
Use the phy_types variable to determine what phy types are possible
when link is down instead of device id as it will be more accurate.

When on a backplane device, we do not support changing any settings,
however we should display all the phy_types we are capable of so if we
see a backplane dev ID set supported and advertised purely based on
the phy_types variable.

Change-ID: Ia75d560f1fcd30c54cbfb7458690c5867559a930
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a module_types variable to the link_info struct to save the module
information from get_phy_capabilities. This information can be used to
determine which speeds the module supports.

Also add a new function update_link_info which updates the module_types
parameter and then calls get_link_info. This function should be called
in place of get_link_info so that the module_types variable stays
up-to-date with the rest of the link information.

The EAS table does not reflect the values that are actually returned,
so instead, basing these values on the Ethernet compliance codes
specified in table 33 of SFF-8436 as these have been accurate.

Use the new variable in ethtool to differentiate between a 10G/1G dual
speed fiber module and a 10G only module.

Change-ID: Ib7585cce321319c10ce15180054c41a6cbd41389
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to desires to write userland drivers, and other requests, without
needing the rest of the include files, the device ids are pulled out
into a standalone file.

Change-ID: Ic0b047dbf9d4b0891892309c1f2079f56d9b60e8
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch moves the internal fw version and fw api version info to be
output in probe.  The nvm version, etrack and oem version info are now
configured for output via ethtool -i.

Change-ID: I05d490093a7137dbefcdef263d014d1e5c9e83d0
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>