Remove extra return statement in omapdss_default_get_recommended_bpp
from overlay.c
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

An overlay in YUV mode has to have an even input width, because data for
each pixel is divided between two adjacent pixels.

The algorithm handling manual update overlay adjusting may adjust the
overlay width to be odd.

This patch adds a check for that situation, and makes the width even.
The width is increased by one if it is possible (the unadjusted input
width is larger than the width), and decreased by one if increasing is
not possible.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Using bool silently converted input to 0 or 1, making the range check
useless. Use unsigned long instead, and convert to bool later. Found by
Coverity.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Unsigned regno can never be less than zero. Found by Coverity.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Unsigned rotate can never be less than zero. Found by Coverity.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Make sure NULL return value of fb2display() is not referenced. Found by
Coverity.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Skip any further processing of taal_enable_te(), taal_rotate(), and
taal_mirror() if value remains unchanged.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

OMAP DSS HW cannot send updates with odd widths. Normally the widths are
made even while preparing the update.

This patch adds a BUG_ON() to check if the update width is even. This is
to detect broken updates cleanly, as otherwise the OMAP DSS HW will just
halt, leading to obscure error situations.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The current FIFO low threshold was too low, and caused the FIFO to run
empty when core domain went to INA state between FIFO fills. This patch
increases the low threshold to keep that from happening.

The threshold values depend quite much on the HW and the use cases, so
this should actually be somehow configurable from board files, perhaps.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The code presumed that all ComplexIO interrupts are errors. This is not
the case. This patch adds proper error mask for CIO interrupt handling.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

SMRPS function always sent BTA after sending the SMRPS packet. This is
not needed, and also caused some (buggy) panels to bug. This patch
removes the BTA.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Currently the update area on manual update displays is automatically
enlargened to fully cover scaled overlays. This patch makes that
optional, allowing the panel driver to choose if it's used or not.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Previously a work was started on FRAMEDONE interrupt, and this work
either sent a BTA synchronously or looped until TE_SIZE was zero, to
wait for the end of the transfer.

This patch changes a BTA to be sent asynchronously from FRAMEDONE
interrupt, and when a BTA interrupt is received, the transfer is
finished. This way we do the whole process asynchronously, and also
inside interrupt context.

This will give us much better latency to handle the end of the frame
than with the previous work based solution.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Change dsi_vc_config_l4/vp() to loop for the VC_BUSY flag to change, and
return an error if it fails.

Busy looping is bad, but there's no interrupt that can be used for all the
cases where VC can be busy. So the caller should first try to make sure
that the VC is not busy, if possible, and then call dsi_vc_config_l4/vp().

Most notable case when the caller cannot be sure if the VC is busy is
after frame has been sent. Usually DSI buffers have been emptied until we
need to reconfig the VC, but in some rare cases the VC can still be busy,
and this patch will handle that case.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Once the DSI PLL is separated from the DSI display a full DSI reset will
not be performed every time the display is enabled so the interface and
VCs must be disabled when disabling the display. If the VCs are not
disabled some register accesses will abort.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The TRM tells us to wait for the DSI PLL derived clocks to become
active before selecting them for use. I didn't actually have any issues
which this would fix but according to the TRM it seems to be the right
thing to do.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Print an error message if dsi_calc_clock_rates() fails just like it's
done when dispc_calc_clock_rates() fails.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Do not leave the free running pixel clock enabled if the DSI PLL reset
times out.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Prepare for supporting panels other than Taal in this driver.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add support for configuring regulators in the panel specific
configuration data.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The driver will support other panels in addition to Taal, print also the
name.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add a structure for panel specific configration to be able to support
more than one panel in the future.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Make ESD check usage configurable in DSI panel data, as opposed to a
define.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Get board specific information from the Nokia DSI panel data structure
instead of the DSS.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Introduce a configuration struct for platform/board specific information
of Nokia DSI command mode panels, to be used in addition to struct
omap_dss_device (passed via the 'void *data' member).
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add gpio irq based external TE support with timeout.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Switch from numbered to named labels to make it easier to add new
labels for error handling.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move ESD work queuing and cancelling out of taal_power_on/off() to avoid
problems related to taal_esd_work() calling the power on/off functions.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Change state only if power on was succesful.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move dsi_bus_lock/unlock() out of taal_power_on/off() to avoid deadlock
in taal_esd_work().
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Bail out from taal_enable_te() and taal_run_test() if panel is not
enabled.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Check return values and bail out on errors.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

ESD work is never queued in probe, no need to cancel it on probe error.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Separate gpio_request() and request_irq() error handling.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

After the addition of proper hardware reset, taal_hw_reset(), there's no
need for an additional platform enable/disable. Remove them.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Avoid potential race conditions in sysfs access to taal data.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Issue a proper reset pulse on the reset line instead of just doing power
on/off.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

taal_bl_update_status was missing locks to protect taal_data. This caused
a kernel crash randomly, as the code attempted to set the brightness while
the OMAP's DSI block was actually disabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Using nanoseconds as arguments to functions that set the DSI timeouts was
perhaps not so good idea. The timeouts are based on different DSI clocks,
so the possible range for the timeouts vary greatly depending on the
clocks. Also, the multipliers used with the timeouts cause big gaps in the
timeout range, meaning that the nanosecond based functions could cause the
timeout to be quite far from the intended value.

This patch changes the functions to take the plain tick values with the
multiplier enable/disable bits, and sets the TA/LP_RX/HS_TX timeouts to
maximum. While the timeouts could be much lower, the fact is that when
TA/LP_RX/HS_TX timeout happens, we are in an error situation and not in a
hurry anyway.

STOP_STATE_COUNTER is a different matter, but it is only used at
initialization time, and won't normally affect the performance.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Check if the peripheral answered something, and if so, dump the data
and return an error.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>