When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.

Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.

v2:
- add small helper and init the number of actual ports only

Fixes: 364e9d77 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ip rules, we need to use 'ipproto ipv6-icmp' to match ICMPv6 headers.
But for ip -6 route, currently we only support tcp, udp and icmp.

Add ICMPv6 support so we can match ipv6-icmp rules for route lookup.

v2: As David Ahern and Sabrina Dubroca suggested, Add an argument to
rtm_getroute_parse_ip_proto() to handle ICMP/ICMPv6 with different family.
Reported-by: NJianlin Shi <jishi@redhat.com>
Fixes: eacb9384 ("ipv6: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It has been observed that tx queue stalls while downloading
from certain web sites (example www.speedtest.net)

The cause has been tracked down to a corner case where
dma descriptors where not setup properly. And there for a tx
completion interrupt was not signaled.

This fix corrects the problem by properly marking the end of
a multi descriptor transmission.

Fixes: 23f0703c ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: NBryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.

v2:
- use right function name in subject
v3:
- initialize additional fields

Fixes: 9525ae83 ("phylink: add phylink infrastructure")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently the maximum number of queues was increased up to 8, but
NIC was not fully configured for 8 queues. In setups with more than 4 CPU
cores parts of TX traffic gets lost if the kernel routes it to queues 4th-8th.

This patch sets a tx hw traffic mode with 8 queues.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202651

Fixes: 71a963cf ("net: aquantia: increase max number of hw queues")
Reported-by: NNicholas Johnson <nicholas.johnson@outlook.com.au>
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation for UDP GRO tests is racy: the receiver
may flush the RX queue while the sending is still transmitting and
incorrectly report RX errors, with a wrong number of packet received.

Add explicit timeouts to the receiver for both connection activation
(first packet received for UDP) and reception completion, so that
in the above critical scenario the receiver will wait for the
transfer completion.

Fixes: 3327a9c4 ("selftests: add functionals test for UDP GRO")
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Acked-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.

Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.

This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.

Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.

This was tested on 6390X using RXAUI mode.

Fixes: 364e9d77 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined.  Fix
the combing, which wrongly worked on u16's.

Fixes: 80c4627b ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: NChris Healy <Chris.Healy@zii.aero>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Occasionally, during the disconnection procedure on XenBus which
includes hash cache deinitialization there might be some packets
still in-flight on other processors. Handling of these packets includes
hashing and hash cache population that finally results in hash cache
data structure corruption.

In order to avoid this we prevent hashing of those packets if there
are no queues initialized. In that case RCU protection of queues guards
the hash cache as well.
Signed-off-by: NIgor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: NPaul Durrant <paul.durrant@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Zero-copy callback flag is not yet set on frag list skb at the moment
xenvif_handle_frag_list() returns -ENOMEM. This eventually results in
leaking grant ref mappings since xenvif_zerocopy_callback() is never
called for these fragments. Those eventually build up and cause Xen
to kill Dom0 as the slots get reused for new mappings:

"d0v0 Attempt to implicitly unmap a granted PTE c010000329fce005"

That behavior is observed under certain workloads where sudden spikes
of page cache writes coexist with active atomic skb allocations from
network traffic. Additionally, rework the logic to deal with frag_list
deallocation in a single place.
Signed-off-by: NPaul Durrant <paul.durrant@citrix.com>
Signed-off-by: NIgor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to Documentation/core-api/printk-formats.rst, size_t should be
printed with %zu, rather than %Zu.

In addition, using %Zu triggers a warning on clang (-Wformat-extra-args):

net/sctp/chunk.c:196:25: warning: data argument not used by format string [-Wformat-extra-args]
                                    __func__, asoc, max_data);
                                    ~~~~~~~~~~~~~~~~^~~~~~~~~
./include/linux/printk.h:440:49: note: expanded from macro 'pr_warn_ratelimited'
        printk_ratelimited(KERN_WARNING pr_fmt(fmt), ##__VA_ARGS__)
        ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~
./include/linux/printk.h:424:17: note: expanded from macro 'printk_ratelimited'
                printk(fmt, ##__VA_ARGS__);                             \
                       ~~~    ^

Fixes: 5b5e0928 ("lib/vsprintf.c: remove %Z support")
Link: https://github.com/ClangBuiltLinux/linux/issues/378Signed-off-by: NMatthias Maennich <maennich@google.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It can be reproduced by following steps:
1. virtio_net NIC is configured with gso/tso on
2. configure nginx as http server with an index file bigger than 1M bytes
3. use tc netem to produce duplicate packets and delay:
   tc qdisc add dev eth0 root netem delay 100ms 10ms 30% duplicate 90%
4. continually curl the nginx http server to get index file on client
5. BUG_ON is seen quickly

[10258690.371129] kernel BUG at net/core/skbuff.c:4028!
[10258690.371748] invalid opcode: 0000 [#1] SMP PTI
[10258690.372094] CPU: 5 PID: 0 Comm: swapper/5 Tainted: G        W         5.0.0-rc6 #2
[10258690.372094] RSP: 0018:ffffa05797b43da0 EFLAGS: 00010202
[10258690.372094] RBP: 00000000000005ea R08: 0000000000000000 R09: 00000000000005ea
[10258690.372094] R10: ffffa0579334d800 R11: 00000000000002c0 R12: 0000000000000002
[10258690.372094] R13: 0000000000000000 R14: ffffa05793122900 R15: ffffa0578f7cb028
[10258690.372094] FS:  0000000000000000(0000) GS:ffffa05797b40000(0000) knlGS:0000000000000000
[10258690.372094] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10258690.372094] CR2: 00007f1a6dc00868 CR3: 000000001000e000 CR4: 00000000000006e0
[10258690.372094] Call Trace:
[10258690.372094]  <IRQ>
[10258690.372094]  skb_to_sgvec+0x11/0x40
[10258690.372094]  start_xmit+0x38c/0x520 [virtio_net]
[10258690.372094]  dev_hard_start_xmit+0x9b/0x200
[10258690.372094]  sch_direct_xmit+0xff/0x260
[10258690.372094]  __qdisc_run+0x15e/0x4e0
[10258690.372094]  net_tx_action+0x137/0x210
[10258690.372094]  __do_softirq+0xd6/0x2a9
[10258690.372094]  irq_exit+0xde/0xf0
[10258690.372094]  smp_apic_timer_interrupt+0x74/0x140
[10258690.372094]  apic_timer_interrupt+0xf/0x20
[10258690.372094]  </IRQ>

In __skb_to_sgvec(), the skb->len is not equal to the sum of the skb's
linear data size and nonlinear data size, thus BUG_ON triggered.
Because the skb is cloned and a part of nonlinear data is split off.

Duplicate packet is cloned in netem_enqueue() and may be delayed
some time in qdisc. When qdisc len reached the limit and returns
NET_XMIT_DROP, the skb will be retransmit later in write queue.
the skb will be fragmented by tso_fragment(), the limit size
that depends on cwnd and mss decrease, the skb's nonlinear
data will be split off. The length of the skb cloned by netem
will not be updated. When we use virtio_net NIC and invoke skb_to_sgvec(),
the BUG_ON trigger.

To fix it, netem returns NET_XMIT_SUCCESS to upper stack
when it clones a duplicate packet.

Fixes: 35d889d1 ("sch_netem: fix skb leak in netem_enqueue()")
Signed-off-by: NSheng Lan <lansheng@huawei.com>
Reported-by: NQin Ji <jiqin.ji@huawei.com>
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two array out-of-bounds memory accesses, one in
cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk().  Both
errors are embarassingly simple, and the fixes are straightforward.

As a FYI for anyone backporting this patch to kernels prior to v4.8,
you'll want to apply the netlbl_bitmap_walk() patch to
cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before
Linux v4.8.
Reported-by: NJann Horn <jannh@google.com>
Fixes: 446fda4f ("[NetLabel]: CIPSOv4 engine")
Fixes: 3faa8f98 ("netlabel: Move bitmap manipulation functions to the NetLabel core.")
Signed-off-by: NPaul Moore <paul@paul-moore.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip_route_input_rcu expects the original ingress device (e.g., for
proper multicast handling). The skb->dev can be changed by l3mdev_ip_rcv,
so dev needs to be saved prior to calling it. This was the behavior prior
to the listify changes.

Fixes: 5fa12739 ("net: ipv4: listify ip_rcv_finish")
Cc: Edward Cree <ecree@solarflare.com>
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
selftests: pmtu: fix and increase coverage

This series includes a fixup for the pmtu.sh test script, related to IPv6
address management, and adds coverage for the recently reported and fixed
PMTU exception issue

v2 -> v3:
 - more cleanups

v1 -> v2:
 - several script cleanups
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a couple of new tests, explicitly checking that the kernel
timely releases PMTU exceptions on related device removal.
This is mostly a regression test vs the issue fixed by
commit f5b51fe8 ("ipv6: route: purge exception on removal")

Only 2 new test cases have been added, instead of extending all
the existing ones, because the reproducer requires executing
several commands and would slow down too much the tests otherwise.

v2 -> v3:
 - more cleanup, still from Stefano

v1 -> v2:
 - several script cleanups, as suggested by Stefano
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise, the configured IPv6 address could be still "tentative"
at test time, possibly causing tests failures.
We can also drop some sleep along the code and decrease the
timeout for most commands so that the test runtime decreases.

v1 -> v2:
 - fix comment (Stefano)

Fixes: d1f1b9cb ("selftests: net: Introduce first PMTU test")
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to dp83640 delay after soft reset
is needed to set up registers correctly.
Signed-off-by: NMax Uvarov <muvarov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

KASAN report this:

BUG: KASAN: null-ptr-deref in nfc_llcp_build_gb+0x37f/0x540 [nfc]
Read of size 3 at addr 0000000000000000 by task syz-executor.0/5401

CPU: 0 PID: 5401 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xfa/0x1ce lib/dump_stack.c:113
 kasan_report+0x171/0x18d mm/kasan/report.c:321
 memcpy+0x1f/0x50 mm/kasan/common.c:130
 nfc_llcp_build_gb+0x37f/0x540 [nfc]
 nfc_llcp_register_device+0x6eb/0xb50 [nfc]
 nfc_register_device+0x50/0x1d0 [nfc]
 nfcsim_device_new+0x394/0x67d [nfcsim]
 ? 0xffffffffc1080000
 nfcsim_init+0x6b/0x1000 [nfcsim]
 do_one_initcall+0xfa/0x5ca init/main.c:887
 do_init_module+0x204/0x5f6 kernel/module.c:3460
 load_module+0x66b2/0x8570 kernel/module.c:3808
 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f9cb79dcc58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000280 RDI: 0000000000000003
RBP: 00007f9cb79dcc70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9cb79dd6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004

nfc_llcp_build_tlv will return NULL on fails, caller should check it,
otherwise will trigger a NULL dereference.
Reported-by: NHulk Robot <hulkci@huawei.com>
Fixes: eda21f16 ("NFC: Set MIU and RW values from CONNECT and CC LLCP frames")
Fixes: d646960f ("NFC: Initial LLCP support")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.

DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).

END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.

WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
   register 2, prior to connecting the cable or prior to setting the
   Restart Auto-negotiation bit in register 0h. The MMD registers are
   accessed via the indirect access registers Dh and Eh, or via the Micrel
   EthUtil utility as shown here:
   . if using the EthUtil utility (usually with a Micrel KSZ8061
     Evaluation Board), type the following commands:
     > address 1
     > mmd 1
     > iw 2 b61a
   . Alternatively, write the following registers to write to the
     indirect MMD register:
     Write register Dh, data 0001h
     Write register Eh, data 0002h
     Write register Dh, data 4001h
     Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
   either by the strapping option, or by clearing bit 12 in register 0h.
   Care must be taken to ensure that the KSZ8061 and the link partner
   will link with the same speed and duplex. Note that the KSZ8061
   defaults to full-duplex when auto-negotiation is off, but other
   devices may default to half-duplex in the event of failed
   auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
   or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
   be recovered by setting the Restart Auto-Negotiation bit in
   register 0h, or by resetting or power cycling the device. Reset may
   be either hardware reset or software reset (register 0h, bit 15).

PLAN
This errata will not be corrected in the future revision.

Fixes: 7ab59dc1 ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: NAlexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: NRajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netif_msg_init() API takes on input the amount of bits to be set. The
description of debug parameter in the enc28j60 module is misleading in this
sense and passing 0xffff does not give an expected behaviour.

Fix the description of debug module parameter to show what exactly is expected.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1 << 31 is Undefined Behaviour according to the C standard.
Use U type modifier to avoid theoretical overflow.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions.  The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU.  Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.

In the meantime, add a quick length check in the driver to prevent
the error.  The driver uses the TX packet size as index to look up an
array to setup the TX BD.  The array is large enough to support all MTU
sizes supported by the driver.  The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD.  Add a simple check to prevent this.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.

CPU-0                                | CPU-1
tipc_wait_for_cond()                 |
{                                    |
 // condition_ = !tsk->cong_link_cnt |
 while ((rc_ = !(condition_))) {     |
  ...                                |
  release_sock(sk_);                 |
  wait_woken();                      |
                                     | if (!sock_owned_by_user(sk))
                                     |  tipc_sk_filter_rcv()
                                     |  {
                                     |   ...
                                     |   tipc_sk_proto_rcv()
                                     |   {
                                     |    ...
                                     |    tsk->cong_link_cnt--;
                                     |    ...
                                     |    sk->sk_write_space(sk);
                                     |    ...
                                     |   }
                                     |   ...
                                     |  }
  sched_annotate_sleep();            |
  lock_sock(sk_);                    |
  remove_wait_queue();               |
 }                                   |
}                                    |

This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NTung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: Fail route add with unsupported nexthop attribute

RTA_VIA was added for MPLS as a way of specifying a gateway from a
different address family. IPv4 and IPv6 do not currently support RTA_VIA
so using it leads to routes that are not what the user intended. Catch
and fail - returning a proper error message.

MPLS on the other hand does not support RTA_GATEWAY since it does not
make sense to have a nexthop from the MPLS address family. Similarly,
catch and fail - returning a proper error message.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.

Fixes: 03c05665 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:

  $ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
  $ ip ro ls
  ...
  2001:db8:2::/64 dev eth0 metric 1024 pref medium

Catch this and fail the route add:
  $ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
  Error: IPv6 does not support RTA_VIA attribute.

Fixes: 03c05665 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:

  $ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
  $ ip ro ls
  ...
  172.16.1.0/24 dev eth0

Catch this and fail the route add:
  $ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
  Error: IPv4 does not support RTA_VIA attribute.

Fixes: 03c05665 ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract IP options in cipso_v4_error and use __icmp_send.
Signed-off-by: NSergey Nazarov <s-nazarov@yandex.ru>
Acked-by: NPaul Moore <paul@paul-moore.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add __icmp_send function having ip_options struct parameter
Signed-off-by: NSergey Nazarov <s-nazarov@yandex.ru>
Reviewed-by: NPaul Moore <paul@paul-moore.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace set_current_state with __set_current_state since no memory
barrier is needed at this point.
Signed-off-by: NTimur Celik <mail@timurcelik.de>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 9060cb71 ("net: crypto set sk to NULL when af_alg_release.")
fixed a use-after-free in sockfs_setattr() when an AF_ALG socket is
closed concurrently with fchownat().  However, it ignored that many
other proto_ops::release() methods don't set sock->sk to NULL and
therefore allow the same use-after-free:

    - base_sock_release
    - bnep_sock_release
    - cmtp_sock_release
    - data_sock_release
    - dn_release
    - hci_sock_release
    - hidp_sock_release
    - iucv_sock_release
    - l2cap_sock_release
    - llcp_sock_release
    - llc_ui_release
    - rawsock_release
    - rfcomm_sock_release
    - sco_sock_release
    - svc_release
    - vcc_release
    - x25_release

Rather than fixing all these and relying on every socket type to get
this right forever, just make __sock_release() set sock->sk to NULL
itself after calling proto_ops::release().

Reproducer that produces the KASAN splat when any of these socket types
are configured into the kernel:

    #include <pthread.h>
    #include <stdlib.h>
    #include <sys/socket.h>
    #include <unistd.h>

    pthread_t t;
    volatile int fd;

    void *close_thread(void *arg)
    {
        for (;;) {
            usleep(rand() % 100);
            close(fd);
        }
    }

    int main()
    {
        pthread_create(&t, NULL, close_thread, NULL);
        for (;;) {
            fd = socket(rand() % 50, rand() % 11, 0);
            fchownat(fd, "", 1000, 1000, 0x1000);
            close(fd);
        }
    }

Fixes: 86741ec2 ("net: core: Add a UID field to struct sock.")
Signed-off-by: NEric Biggers <ebiggers@google.com>
Acked-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Metadata pointer is only initialized for action TCA_TUNNEL_KEY_ACT_SET, but
it is unconditionally dereferenced in tunnel_key_init() error handler.
Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.

Fixes: ee28bb56 ("net/sched: fix memory leak in act_tunnel_key_init()")
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Reviewed-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
Signed-off-by: NWen Yang <wen.yang99@zte.com.cn>
Reviewed-by: NVivien Didelot <vivien.didelot@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.
Signed-off-by: NTimur Celik <mail@timurcelik.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the file names of the FW files which this driver handles into
the module description.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when act_skbedit was converted to use RCU in the data plane, we added an
error path, but we forgot to drop the action refcount in case of failure
during a 'replace' operation:

 # tc actions add action skbedit ptype otherhost pass index 100
 # tc action show action skbedit
 total acts 1

         action order 0: skbedit  ptype otherhost pass
          index 100 ref 1 bind 0
 # tc actions replace action skbedit ptype otherhost drop index 100
 RTNETLINK answers: Cannot allocate memory
 We have an error talking to the kernel
 # tc action show action skbedit
 total acts 1

         action order 0: skbedit  ptype otherhost pass
          index 100 ref 2 bind 0

Ensure we call tcf_idr_release(), in case 'params_new' allocation failed,
also when the action is being replaced.

Fixes: c749cdda ("net/sched: act_skbedit: don't use spinlock in the data path")
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 4e8ddd7f ("net: sched: don't release reference on action
overwrite"), the error path of all actions was converted to drop refcount
also when the action was being overwritten. But we forgot act_ipt_init(),
in case allocation of 'tname' was not successful:

 # tc action add action xt -j LOG --log-prefix hello index 100
 tablename: mangle hook: NF_IP_POST_ROUTING
         target:  LOG level warning prefix "hello" index 100
 # tc action show action xt
 total acts 1

         action order 0: tablename: mangle  hook: NF_IP_POST_ROUTING
         target  LOG level warning prefix "hello"
         index 100 ref 1 bind 0
 # tc action replace action xt -j LOG --log-prefix world index 100
 tablename: mangle hook: NF_IP_POST_ROUTING
         target:  LOG level warning prefix "world" index 100
 RTNETLINK answers: Cannot allocate memory
 We have an error talking to the kernel
 # tc action show action xt
 total acts 1

         action order 0: tablename: mangle  hook: NF_IP_POST_ROUTING
         target  LOG level warning prefix "hello"
         index 100 ref 2 bind 0

Ensure we call tcf_idr_release(), in case 'tname' allocation failed, also
when the action is being replaced.

Fixes: 4e8ddd7f ("net: sched: don't release reference on action overwrite")
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull KVM fixes from Paolo Bonzini:
 "Bug fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
  kvm: x86: Return LA57 feature based on hardware capability
  x86/kvm/mmu: fix switch between root and guest MMUs
  s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity