When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The section had two tabs instead of one.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The board uses McASP1 <-> tlv320aic3106 for analog audio and has
Headphone out and Line in connectors.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Analog audio is using this codec on the board.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The same regulator is used by other chips on the board. The power path is:
VBAT -> TPS63031 - Enable signal is V1_8D regulator -> V3_3D.
V3_3D is used by SD slot and tlv320aic3106 codec as well.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO5_8 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use simple card for audio support on ePOS-EVM.
The audio on the board is: McASP1 <-> tlv320aic3111 codec.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Analog audio is using this codec on the board.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The VBAT and DCDC4 regulator is needed for audio support (tlv320aic3111)
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO2_1 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The sound support consist only Headset output on the board and can be
handled by "simple-audio-card".
Also enable the Line-In route as the board has support for it.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. Add gpio hog entry to pcf_gpio_21 in order to
select cpsw slave0.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The interconnects on dm816x are like on omap4, so we should use
l3-noc instead of l3-smx. But as the related SoC specific
l3_target_data is still missing from omap_l3_noc let's just
remove the entry for now.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reported-by: NMatthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Also, reduce the maximum SPI device speed to the max. supported by the
LCD controller used on the LGPhilips LB035Q02 panel for this board.
Signed-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Some Overo COM models include NAND flash in the on-board
package-on-package (PoP) chip.  Add this to the base Overo devicetree.

Most commonly, this is 512MB NAND from the Micron MT29C4G96MAZ family
but, as discussed [1], several different sized are possible. To
support different sizes, the last partition should fill to the end of
the chip (i.e. MTDPART_SIZ_FULL).

With thanks to Florian Vaussard for the original patch [2] and Adam Lee for
updating it here.

[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2013-June/175760.html
[2] http://lists.infradead.org/pipermail/linux-arm-kernel/2013-June/175449.htmlSigned-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Both Gumstix Overo and Overo Storm COMs use TWL4030 audio module
connected to the McBSP2.  As such, enable the McBSP2 module in the
common device tree file, omap3-overo-base.dtsi, rather than in the
processor-specific device tree files, omap3-overo.dtsi and
omap3-overo-storm.dtsi.  This corrects audio on the Storm COMs where
the setting was accidentally missing from the device tree.
Signed-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Gumstix "Tobi-Duo" expansion board [1] can be used with either
OMAP3 Overo or Overo Storm COMs.  It provides two NICs using LAN9221
chips.
It is necessary to duplicate the interface information for the
second SMSC9221 chip as discussed [2].

[1] https://store.gumstix.com/index.php/products/241/
[2] http://www.spinics.net/lists/linux-omap/msg115282.htmlSigned-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use new binding for the external tda19988 HDMI encoder.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The sDMA requests are routed through the DMA crossbar and without the
crossbar only peripherals using DMA request 0-127 can be used.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the Wakeup M3 remote processor device node for
the AM4372 SoC. The WkupM3 remote processor is used
to implement and achieve low-power functionality on
the AM33xx & AM43xx SoCs.

This node is added as a child of the recently added
l4_wkup node to reflect its presence within the SoC.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The WakeupM3 remote processor device node has been moved to
be a child node of the newly created l4_wkup node, to reflect
its presence properly within the SoC. The node was added
previously before any driver support, it is now updated as
per the wkup_m3_rproc bindings added alongside the driver
support.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The CCI device node was added to vexpress CA15_A7(i.e. TC2) much before
the CCI PMU support and binding was added. This patch adds the missing
PMU node so that CCI PMUs can be used on TC2.

Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NPunit Agrawal <punit.agrawal@arm.com>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

The dts for the CoreTile Express A15x2 A7x3 (TC2) only describes the
PMUs of the Cortex-A15 CPUs, and not the Cortex-A7 CPUs.

Now that we have a mechanism for describing disparate PMUs and their
interrupts in device tree, this patch makes use of these to describe the
PMUs for all CPUs in the system. For consistency, the existing A15 PMU
interrupt-affinity property is reflowed across two lines.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NSudeep Holla <sudeep.holla@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

When DSS nodes were added to am4372.dtsi, the rfbi node was not marked
as disabled. This should have been done, as the rule of thumb is to
disable all DSS nodes that are not used, and especially rfbi, as we
don't have a driver for rfbi.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Without this USB2 breaks if USB1 is disabled or USB1
initializes after USB2 e.g. due to deferred probing.

Fixes: 5a0f93c6 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Cc: stable@vger.kernel.org (v3.19+)
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add node for TI AM4372 EMIF. Without this we get a warning with the
recent commit fabbe6df (ARM: OMAP: AM43xx hwmod: Add data for am43xx
emif hwmod).
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This reverts commit 3d76be5b.

The latest revision of Beaglebone Black does not support RTC-only mode.

To avoid potential hardware damage, RTC-only mode was disabled by
default by commit 7a6cb0ab ("ARM: dts: am335x-boneblack: disable
RTC-only sleep to avoid hardware damage").

Unfortunately, an incorrect fix had already been applied, which instead
of just disabling RTC-only mode, prevents the Beaglebone from powering
down at all.

Revert this patch to fix the power-off regression.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

at91sam9g45, at91sam9x5 and sama5 SoCs should not use
"atmel,at91sam9rl-udc" for their USB device compatible property since
this compatible is attached to a specific hardware bug fix.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>  #4.0+
Signed-off-by: NKevin Hilman <khilman@linaro.org>

This patch updates the Ethernet DT nodes for Armada XP SoCs with the
compatible string "marvell,armada-xp-neta".
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Fixes: 77916519 ("arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces")
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This backs out all changes that were added in the hip04-dt
branch after various boot problems were discovered in UEFI booting.
Reported-by: NTyler Baker <tyler.baker@linaro.org>
Cc: Wei Xu <xuwei5@hisilicon.com>
[khilman: minor changelog updates]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

Add support for the Arria10 SDRAM EDAC. Update the bindings document for
the new match string.
Signed-off-by: NThor Thayer <tthayer@opensource.altera.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree@vger.kernel.org
Cc: dinguyen@opensource.altera.com
Cc: galak@codeaurora.org
Cc: grant.likely@linaro.org
Cc: ijc+devicetree@hellion.org.uk
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: m.chehab@samsung.com
Cc: mark.rutland@arm.com
Cc: pawel.moll@arm.com
Cc: robh+dt@kernel.org
Cc: tthayer.linux@gmail.com
Link: http://lkml.kernel.org/r/1433428128-7292-5-git-send-email-tthayer@opensource.altera.comSigned-off-by: NBorislav Petkov <bp@suse.de>

The clock which was named as 'pll_clk' is actually not the clock source
of PLL in MIPI DSI. This patch fixes this disagreement.
Signed-off-by: NHyungwon Hwang <human.hwang@samsung.com>
Acked-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Following the merge of "pinctrl: mvebu: armada-xp: rename spi to spi0"
by Linus Walleij, we need to adjust the Armada XP Device Tree
accordingly, by adjusting the pinctrl configuration for SPI pins.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add initial dts file and document for ZX296702 and board ZX296702-AD1.
More peripherals will be added later.
Signed-off-by: NJun Nie <jun.nie@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

Adjust device tree entry to the proper registered compatible
string for LIS3LV02DL.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

The xdmac channel configuration is done in one cell not two. This error
prevents from probing devices correctly.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Fixes: 83906783 ("ARM: at91/dt: sama5d4: add aes, sha and tdes nodes")
Cc: stable@vger.kernel.org # 4.1
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

The STMicrolectornics's STM32F429 MCU has the following main features:
 - Cortex-M4 core running up to @180MHz
 - 2MB internal flash, 256KBytes internal RAM
 - FMC controller to connect SDRAM, NOR and NAND memories
 - SD/MMC/SDIO support
 - Ethernet controller
 - USB OTFG FS & HS controllers
 - I2C, SPI, CAN busses support
 - Several 16 & 32 bits general purpose timers
 - Serial Audio interface
 - LCD controller
Tested-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMaxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>