WCN6855 needs a different reo configuration, so add separate handling
for this target in ath11k_hw_ops.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NBaochen Qiang <bqiang@codeaurora.org>
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-4-jouni@codeaurora.org

hal rx descriptor is different for WCN6855 and there are such a lot
of handlers processing this descriptor in data path. So add separate
handling for this target.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: NBaochen Qiang <bqiang@codeaurora.org>
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-3-jouni@codeaurora.org

Reg address of WCN6855 is different from other devices,
so add separate reg definition for this target.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NBaochen Qiang <bqiang@codeaurora.org>
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-2-jouni@codeaurora.org

Update the specific hw ring mask for QCN9074. Update the timestamp
information while processing DP and CE interrupts.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-11-git-send-email-akolli@codeaurora.org

hal rx descriptor is different for QCN9074 target type. since
rx_msdu_end, rx_msdu_start, rx_mpdu_start elements are in
different placement/alignment. In order to have generic data path,
introduce platform specific hal rx descriptor access ops in
ath11k_hw_ops.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-9-git-send-email-akolli@codeaurora.org

Define the hal ring address and ring meta descriptor mask for
QCN9074. Move the platform specific address to the ath11k_hw_regs.
Define tx_mesh_enable ops in ath11k_hw_ops since its accessing
platform specific TCL descriptor.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-8-git-send-email-akolli@codeaurora.org

qmi service_ins_id is unique for QCA6390 and QCN9074,
this is needed for adding QCN9074 support. No functional
changes.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-3-git-send-email-akolli@codeaurora.org

Now that all the needed pieces are in place implement suspend support QCA6390
PCI devices. All other devices will return -EOPNOTSUPP during suspend. The
suspend is implemented by switching the firmware to WoW mode during suspend, so
the firmware will be running on low power mode while host is in suspend.

At the moment we are not able to shutdown and fully power off the device due to
bugs in MHI subsystem, so WoW mode is a workaround for the time being.

During suspend we enable WoW mode, disable CE irq and DP irq, then put MHI to
suspend state.  During resume, driver resumes MHI firstly, then enables CE irq
and dp IRQ, and sends WoW wakeup command to firmware.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-11-git-send-email-kvalo@codeaurora.org

It's recommended to use wmi command WMI_PDEV_SET_HW_MODE_CMDID to put hardware
to dbs mode instead of wmi_init command. This fixes a few strange stability
issues.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-3-git-send-email-kvalo@codeaurora.org

cold boot calibration is the process to calibrate all the channels
during the boot-up to avoid the calibration delay during the
channel change.
During the boot-up, firmware started in cold boot calibration mode
Firmware calibrate all channels and generate CalDb(DDR).
Subsequent wifi bringup will reuse the same CalDb.
Firmware is restarted in normal mode to continue the normal operation.

caldb memory address send to firmware through the QMI message.Firmware
use this address to store the caldb data and use it until next reboot.

This will give the improvement during the channel change. But it is
increasing the boot-up time(up to 15sec depend on number of radios).
So if the user want to reduce the boot-up time and accepting for channel
change delay, user can disable this feature using the module param
cold_boot_cal=0.

Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1
Signed-off-by: NGovindaraj Saminathan <gsamin@codeaurora.org>
Co-developed-by: NSowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: NSowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org

Host sends wmi command to allow hardware enter idle power
save mode in ath11k_mac_op_start function.

hw parameter idle_ps indicates whether idle power save is supported.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-8-git-send-email-kvalo@codeaurora.org

To enable shadow register access, host needs to pass shadow
register configuration to firmware via qmi message. Host also
needs to update ring's HP or TP address to shadow register
address. The write operation to shadow register will be
forwarded to target register by hardware automatically, and
the write operation to shadow register is permitted even
when the target is in power save or sleep mode.

Update the shadow config whenever power up happens.

This feature is controlled by hw parameter supports_shadow_regs which is only
enabled for QCA6390.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-3-git-send-email-kvalo@codeaurora.org

QCA6390 does not support monitor mode at the moment so disable it altogether,
using a hack as mac80211 does not support disabling it otherwise. Add a boolean
to hw_params to know if hardware supports monitor mode.

IPQ8074 continues to support monitor mode normally.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-6-git-send-email-kvalo@codeaurora.org

As QCA6390 does not support mesh interfaces, move the interface_modes to
hw_params. Also create interface combinations dynamically so that it's easy to
change the values.

Now QCA6390 does not claim to support mesh interfaces to user space, but
IPQ8074 continues to do that.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-4-git-send-email-kvalo@codeaurora.org

IPQ6018 supported with 4 bytes FFT BIN size. so supported 4 bytes
parsing logic in FFT report process. since spectral_fft_sz is
configured as zero in hw_params, spectral is not supported in
QCA6390 platform.

Tested-on: IPQ6018 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600236776-4042-1-git-send-email-periyasa@codeaurora.org

Move target CE config and target CE service config to hw_params.
No functional changes.

Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746cb685d9-6bedeccb-29a1-4d32-8664-fcfe7d105f4a-000000@us-west-2.amazonses.com

For QCA6390, wbm2sw1 is used for other purpose rather than
tx completion ring. So use TCL_DATA_RING 0 only for QCA6390.

Add MISC_CAPS_TCL_0_ONLY to control it.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-9-git-send-email-kvalo@codeaurora.org

QCA6390 doesn't enable V2 map and ummap event, so the addr search
flags and type is different from IPQ8074. Assign correct search flags
and type for QCA6390.

Without this change, ping sometimes fails. With this change, now ping
is always successful.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-7-git-send-email-kvalo@codeaurora.org

For QCA6390 firmware, bss peer must be created before vdev_start, so delay
vdev_start until bss peer is created.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-6-git-send-email-kvalo@codeaurora.org

For QCA6390, only one pdev is created and this pdev manages both lmacs, thus
both rxdmas. So host needs to initialize all rxdma related rings for one pdev.

Another difference is for QCA6390, host fills rxbuf to firmware and firmware
further fills the rxbuf to rxbuf ring for each rxdma.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-4-git-send-email-kvalo@codeaurora.org

For QCA6390, it has 2 lmacs and thus 2 rxdmas. However, each rxdma has rxdma0
only, and doesn't have rxdma1. So for QCA6390, don't initialize rxdma1 related
rings such as rx_mon_buf_ring, rx_mon_dst_ring and rx_mon_desc_ring.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-3-git-send-email-kvalo@codeaurora.org

QCA6390 uses MSI interrupt, so need to configure msi_add and
msi_data to dp srngs. As there are so many DP srngs, so need
to group them. Each group shares one MSI interrupt.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-2-git-send-email-kvalo@codeaurora.org

For QCA6390, host puts hardware to Dual Band Simultaneous (DBS) mode by default
so both 2G and 5G bands can be used. Otherwise only the 5G band can be used.
QCA6390 doesn't provide band_to_mac configuration and firmware will do the
band_to_mac map.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-12-git-send-email-kvalo@codeaurora.org

QCA6390 has very different wmi config parameters compared to IPQ8074,
so use different function to initialize wmi init config parameters.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-11-git-send-email-kvalo@codeaurora.org

For QCA6390, only one pdev is created and only one HW is registered to
mac80211. This one pdev manages both 2G radio and 5G radio.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-10-git-send-email-kvalo@codeaurora.org

QCA6390 uses only 9 Copy Engines while IPQ8074 may use 12, make it possible to
change CE configuration dynamically via hw_params.

The defines for host_ce_config_wlan and CE_COUNT are temporary solutions, they
will be removed in the following patches to keep things simple.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-4-git-send-email-kvalo@codeaurora.org

QCA6390 has different register offset compared to IPQ8074, so need to
attach the register offset dynamically based on hw_params.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-2-git-send-email-kvalo@codeaurora.org

On x86 and other non-qcom platforms, host needs to explicitly tell the firmware
to use the internal sleep clock. Some QCA6390 modules have OTP burnt with
external sleep clock selected, and these modules can't work expectedly unless
firmware selects internal sleep clock.

Add a field to hw_params to support this difference.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-11-git-send-email-kvalo@codeaurora.org

PCI devices like QCA6390 have a separate firmware image for the m3
micro-controller. Add support to load the firmware using m3.bin file.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-2-git-send-email-kvalo@codeaurora.org

Modem Host Interface (MHI) is a communication protocol to communicate with
external Qualcomm modems and Wi-Fi chipsets over high speed peripheral buses.
Even though MHI doesn’t dictate underlying physical layer, protocol and MHI
stack is structured for PCI based devices.

Register directly with MHI subsystem as a MHI device driver for firmware
download to QCA6390.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-9-git-send-email-kvalo@codeaurora.org

This is needed for splitting ahb and pci modules as they have different ring
mask settings.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-4-git-send-email-kvalo@codeaurora.org

Define own firmware directory and settings for QCA6390.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-3-git-send-email-kvalo@codeaurora.org

These defines are not used anywhere else so to avoid extra indirection add the
values directly to hw_params.

No functional changes. Compile tested only.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-12-git-send-email-kvalo@codeaurora.org

The downside of using defines in struct ath11k_hw_params.fw.dir is that it's
easy to get it wrong as the full path is not visible. So drop the use of
defines and instead create the patch runtime using a static inline function
ath11k_core_create_firmware_path(). Hopefully this reduces the chances of using
incorrect firmware path.

No functional changes. Compile tested only.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-8-git-send-email-kvalo@codeaurora.org

bdf-addr is different for IPQ8074 and IPQ6018 so add it to hw_params.

No functional changes. Compile tested only.
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-6-git-send-email-kvalo@codeaurora.org

pdev_id to hw_mac is different for ipq8074 and ipq6018
Below table has the mapping

pdev_id	ipq8074	ipq6018
-------	------- -------
  0		0	0
  1		2	1
  2		1	Not applicable

No functional changes. Compile tested only.
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-5-git-send-email-kvalo@codeaurora.org

IPQ6018 needs different value for max_radios so make it configurable via hw_params.

No functional changes. Compile tested only.
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-4-git-send-email-kvalo@codeaurora.org

Convert to ath11k_hw_params to an array to make it possible add new hardware in
the future, for example IPQ6018 or QCA6390.

No functional changes. Compile tested only.
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-3-git-send-email-kvalo@codeaurora.org

Rename default BDF to make it consistent with board-2.bin naming.
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591709581-18039-4-git-send-email-akolli@codeaurora.org

We need this so that all hardware versions can coexist and
it's easier to manage everything then all hardware
directories are under ath11k directory.

Copy ath11k firmware files to
/lib/firmware/ath11k/IPQ8074/hw2.0/
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591709581-18039-3-git-send-email-akolli@codeaurora.org