o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
  to have a bandwidth of at least this value.
  max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
  of up to this value.

o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
  which takes 4 arguments:
  netdev, VF number, min_tx_rate, max_tx_rate

o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.

o Drivers that currently implement ndo_set_vf_tx_rate should now call
  ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
  greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
  implemented by driver.

o If user enters only one of either min_tx_rate or max_tx_rate, then,
  userland should read back the other value from driver and set both
  for IFLA_VF_RATE.
  Drivers that have not yet implemented IFLA_VF_RATE should always
  return min_tx_rate as 0 when read from ip tool.

o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
  IFLA_VF_RATE should override.

o Idea is to have consistent display of rate values to user.

o Usage example: -

  ./ip link set p4p1 vf 0 rate 900

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 6c167f58 ("i40e: Refactor and cleanup i40e_open(),
adding i40e_vsi_open()") introduced a new function i40e_vsi_open()
with the regression by a typo. Due to the commit, the wrong error
code would be passed to i40e_open(). Fix this error in
i40e_vsi_open() by turning the macro into a negative value so that
i40e_open() could return the pertinent error code correctly.

Fixes: 6c167f58 ("i40e: Refactor and cleanup i40e_open(), adding i40e_vsi_open()")
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.

Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The call to i40e_alloc_vfs needs to be wrapped in CONFIG_PCI_IOV because
the function itself is wrapped in the same conditional compile block.

Change-ID: I663c5f1b85e5cfba0b36da8966f7db1a034f408b
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The previous removal of the PTP Tx work functionality was
incomplete as noted by Jake Keller. This removal allows
us to rely on the Tx timesync interrupt.

CC: Jacob Keller <jacob.e.keller@intel.com>
Change-ID: Id4faaf275a3688053ebbf07bef08072f9fd11aa9
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When VFs are assigned to active VMs and we disable SR-IOV out from under them,
bad things happen. Currently, the VM does not crash, but the VFs lose all
resources and have no way to get them back.

Add an additional check for when the user is disabling through sysfs, and add a
comment to clarify why we check twice.

Change-ID: Icad78eef516e4e1e4a87874d59132bc3baa058d4
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Base the queue stats length on the queue stats struct rather than
assuming it is 2 fields.  This is in prep for adding data fields
which are configuration dependent.

Change-ID: I937f471f389d2e0f8cec733960c5d9a06b14f3ec
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For all of our supported kernels, ethtool allows us to directly control
adaptive ITR instead of just faking it with an ITR value. Support this
capability so that user knows explicitly when ITR is being controlled
dynamically. Suggested by Ben Hutchings.

CC: Ben Hutchings <ben@decadent.org.uk>
Change-ID: Iae6b79c5db767a63d22ecd9a9c24acaff02a096e
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Ethtool consistently reports 0 values for our ITR settings because
we never actually set them. Fix this by setting the default values
to the specified default values.

Change-ID: I2832406a66f7140f2b1230945d6ff6cbf77467c8
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Const-ify the ethtool_ops structure, as it is extremely unlikely to
change at runtime. Suggested by Ben Hutchings.

CC: Ben Hutchings <ben@decadent.org.uk>
Change-ID: I1ccb1b7c3ea801cc934447599a35910e7c93d321
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't tell ethtool that the VF can do 10GbaseT, when it really has no
idea what its link speed is. Set the supported values to 0 instead.
Suggested by Ben Hutchings.

CC: Ben Hutchings <ben@decadent.org.uk>
Change-ID: Iceb0d8af68fe5d8dc13224366979ba701ba89c39
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use a macro parameter for ethtool stats instead of just assuming
that a valid netdev variable exists. Suggested by Ben Hutchings.

CC: Ben Hutchings <ben@decadent.org.uk>
Change-ID: I66681698573c1549f95fdea310149d8a7e96a60f
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On some architectures, this header must be explicitly included.

Change-ID: I4bc2eb0531956a7b676489f79d347d55cfe12421
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adding the appropriate GNU General Public License header and
update copyright year to 2014.

Change-ID: I769dd2d37d70350afd0c8727ae2859c0fd340361
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the defines for PCI bus info that are never used.
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Minor changes to the AdminQ interface to bring it up-to-date.

Change-ID: Ie31a4cc4911b2d9d3b7f9af2e56fb0ae674f6345
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It has been determined that the workaround of putting the PHY into MDIO
slow mode to access the PHY id is not necessary with Lynx Point and newer
parts.  The issue that necessitated the workaround has been fixed on the
newer hardware.

We will maintains, as a last ditch attempt, the conversion to MDIO Slow
Mode in the failure branch when attempting to access the PHY id so as to
cover all contingencies.
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
link partners. Issue has been root caused as interoperability problem
between 82579 and at least some Broadcom PHYs in the Energy Efficient
Ethernet wake mechanism.

To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle.  This solution will cause an increase of power in 100M EEE
link. It will cost additional 28mW in this specific mode.

Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com>
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In commit 772d05c5 "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.

This same behavior is seen on i217 and i218 parts as well.  This patch expands
the original workaround to encompass these parts.
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a workaround for a HW erratum on 82579 devices.
Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset
specification Update June 2013.

Problem: 82579 parts experience packet loss in Gig and 100 speeds
when interconnect between PHY and MAC is exiting K1 power saving state.
This was previously believed to only affect 1Gig speed, but has been observed
at 100Mbs also.

Workaround: Disable K1 for 82579 devices at Gig and 100 speeds.
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 0.3.46 and i40evf to 0.9.23.

Change-ID: Ia604ae6d513d9aaa8bfdac79665d9a3a72507df7
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some information returned via "Get Link Status" command was not
being cached in the struct i40e_link_status.
Add this so the driver can utilize this information as needed.

Change-ID: If084a0ae2a63b16b97572196b993742af2c67772
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change the formal parameters to remove argument which is no longer used.

Change-ID: I493b56eba74a1f396fa1b7d24c0a4acbe536b5bf
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Ethtool -k/-K can handle this so we do not need it in debugfs.

Change-ID: I9df692f10a60b71805f8f48d3b87c7da3820b2aa
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Although NTUPLE feature control is disabled by default, do not
allow user to be able to change it.

Change-ID: I4c3f95fb6dbc56b1b6cc47116ea1f72de02bc99c
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change the variable type to avoid compiler warning about int to u16
possible data truncation.

Change-ID: I5eb3b578c86513c9625ca32d2f0b57cc01d7dc98
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the PF driver fails or is removed from the host, the VF driver will
fill up its log with this message.

Change-ID: I67045f987f7c0d444d21ded403adc509343cdb8f
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a panic that would occur in the VF if the PF driver failed or was
removed from the host kernel. In this case, the VF driver calls
i40evf_close(), but this function does nothing because the driver is in
the resetting state. Because of this, the driver doesn't free its irqs
and causes a kernel panic when it tries to disable MSI-X.

Change-ID: If95644a89e554b4d7be0dca1b6add26f63047129
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In case of any AQ command to query port's DCB configuration fails
during driver's probe time; the probe fails and returns an error.

This patch prevents this issue by continuing the driver probe even
when an error is returned.

Also, added an error message to dump the AQ error status to show what
error caused the failure to get the DCB configuration from firmware.

Change-ID: Ifd5663512588bca684069bb7d4fb586dd72221af
Signed-off-by: NNeerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The queue vectors are originally distributed among the total
number of queues that are configured for a given VSI. The number
of queues that are configured for a VSI depends on the number of
TCs that are enabled for the VSI at VSI setup/creation time.

But, the total number of queues that are configured for a VSI may
change based on change in the total number of TCs enabled as a
result of change in DCB configuration based on DCBX.

Hence, it is required for the queue vectors to be redistributed
when the total queues that are configured for a given VSI changes.

Without redistributing the vectors the queues that are configured
for the newly enabled TCs may not be able to do any Tx/Rx.

Change-ID: I4e780903db019e6199c7ce43627cef22c916acfe
Signed-off-by: NNeerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver version string was added to this struct to be passed
down through the firmware to low-level NC-SI functions. We tell
the firmware about the length of the ASCII string not counting
any terminating null.

Change-ID: I09ac98ff9b869e8661c55fc6a5c98808fc280c91
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NAnjali Singhai <anjali.singhai@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function to set the VF MAC address was not taking the port VLAN
filter into account when setting/clearing/resetting the VF's host
administered MAC address.  Be sure to use the port VLAN for VF MAC
filtering configurations.

Change-ID: I12595331981c79529738f041dcdbdb667ef8f5e6
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for getting and setting RSS hashing options, RSS LUT
entries, and getting the number of device channels from ethtool. Because
the LUT is so small for the VFs, we just read and write the device
registers directly instead of maintaining a shadow copy.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We were already taking care to retain the MAC filter list when deleting a
port VLAN.  Take some additional care to retain the MAC filter list when
changing a port VLAN.

Change-ID: Iacf9599ea24ecb4dca8e419aacaf4b58ca361a9c
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the unnecessary ptp_tx_work item. It conflicts with
the interrupt-based handler, and will cause spurious warning messages to
be displayed in the kernel log. Since the hardware can properly trigger
an interrupt, we do not need to poll for an available timestamp in a
work queue any more.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the PTP Tx timestamp interrupt handler. The original
code misinterpreted the interrupt handler design. We were clearing the
ena_mask bit for the Timesync interrupts. This is done to indicate that
the interrupt will be handled in a scheduled work item (instead of
immediately) and that work item is responsible for re-enabling the
interrupts. However, the Tx timestamp was being handled immediately and
nothing was ever re-enabling it. This resulted in a single interrupt
working for the life of the driver.

This patch fixes the issue by instead clearing the bit from icr0 which
is used to indicate that the interrupt was immediately handled and can
be re-enabled right away. This patch also clears up a related issue due
to writing the PRTTSYN_STAT_0 register, which was unintentionally
clearing the cause bits for Timesync interrupts.

Change-ID: I057bd70d53c302f60fab78246989cbdfa469d83b
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes issue found by updated coccicheck.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes issues found by updated coccicheck.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:AVOID_EXTERNS found by checkpatch file check.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>