removing unused function as part of driver cleanup.`
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to view addresses added by the driver and learnt by the
hardware from ALE table via ethtool register dump interface.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

instead of return error on zero rx_coalesce_usecs, disable coalesce
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 629c9a8f (drivers: net: cpsw: Add
default vlan for dual emac case also), api cpsw_add_default_vlan() also
changes the port vlan which is required to seperate the ports which results
in the following behavior

In Dual EMAC mode, when both the Etnernet connected is connected to same
switch, it creates a loop in the switch and when a broadcast packet is
received it is forwarded to the other port which stalls the whole switch
and needs a reset/power cycle to the switch to recover. So intead of using
the api, add only the default VLAN entry in dual EMAC case.

Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Tested-by: NYegor Yefremov <yegorslists@googlemail.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These should not have trailing semicolons so remove them.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert all pr_*() calls to dev_*() calls.
No functional changes.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing of_node_put to avoid kref leak.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix null-pointer dereference at probe when the mdio platform device is
missing (e.g. when it has been disabled in DT).

Cc: stable <stable@vger.kernel.org>	# v3.8
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit f8d56d8f ("net:
 eth: cpsw: Correctly attach to GPIO bitbang MDIO driver").

Fix potential null-pointer dereference at probe if the mdio-gpio device
has not been successfully probed yet.

The offending commit is plain wrong for a number of reasons. First of
all it accesses internal driver data of an unrelated device. Neither
does it check that the data is non-null (which it is in case the device
has not been probed yet).

Furthermore, the decision on whether to treat any driver data according
to the mdio-gpio driver's internals is made based on the node name. But
the name is not compared against "mdio" which is the normal name for the
node, but rather against "gpio" which the node does not have to be named
(and shouldn't be according to the binding documentation). [ If this
hack is to be kept out-of-tree it should at least be matching against
the compatible property. ]

Cc: Stefan Roese <sr@denx.de>
Cc: stable <stable@vger.kernel.org>	# v3.14
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the Annex F Time Sync explicitly for DRA7x and AM4372.
With this enabled the L2 PTP is working.

while at that rename TS_BIT8 to TS_TTL_NONZERO
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable cpts hardware time stamping for Dra7xx and AM4372.
This enables PTPv2 for DRA7xx and AM4372.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the Ethernet interface is put down and up with heavy Ethernet
traffic, then there is prossibility of an interrupt waiting in irq
controller to be processed, so when the interface is brought up again
just after enable interrupt, it goes to ISR due to the previous
unhandled interrutp and in ISR napi is not scheduled as the napi
is not enabled in ndo_open which results in disabled interrupt for
CPSW and no packets are received in cpsw. So this patch moves enabling
of interupts after napi_enable and clearing CPDMA interrupts.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the Ethernet interface is brought down during high Ethernet traffic,
then cpsw creates the following warn dump. When cpdma has already processed
the packet then the status will be greater than 0, so the cpsw_rx_handler
considers that the interface is up and try to resubmit one more rx buffer
to cpdma which fails as the DMA is in teardown process. This can be avoided
by checking the interface state and then process the received packet, if the
interface is down just discard and free the skb and return.

[ 2823.104591] WARNING: CPU: 0 PID: 1823 at drivers/net/ethernet/ti/cpsw.c:711 cpsw_rx_handler+0x148/0x164()
[ 2823.114654] Modules linked in:
[ 2823.117872] CPU: 0 PID: 1823 Comm: ifconfig Tainted: G        W     3.14.0-11992-gf34c4a35 #11
[ 2823.126860] [<c0014b5c>] (unwind_backtrace) from [<c00117e4>] (show_stack+0x10/0x14)
[ 2823.135030] [<c00117e4>] (show_stack) from [<c0533a9c>] (dump_stack+0x80/0x9c)
[ 2823.142619] [<c0533a9c>] (dump_stack) from [<c003f0e0>] (warn_slowpath_common+0x6c/0x90)
[ 2823.151141] [<c003f0e0>] (warn_slowpath_common) from [<c003f120>] (warn_slowpath_null+0x1c/0x24)
[ 2823.160336] [<c003f120>] (warn_slowpath_null) from [<c03caeb0>] (cpsw_rx_handler+0x148/0x164)
[ 2823.169314] [<c03caeb0>] (cpsw_rx_handler) from [<c03c730c>] (__cpdma_chan_free+0x90/0xa8)
[ 2823.178028] [<c03c730c>] (__cpdma_chan_free) from [<c03c7418>] (__cpdma_chan_process+0xf4/0x134)
[ 2823.187279] [<c03c7418>] (__cpdma_chan_process) from [<c03c7560>] (cpdma_chan_stop+0xb4/0x17c)
[ 2823.196349] [<c03c7560>] (cpdma_chan_stop) from [<c03c766c>] (cpdma_ctlr_stop+0x44/0x9c)
[ 2823.204872] [<c03c766c>] (cpdma_ctlr_stop) from [<c03cb708>] (cpsw_ndo_stop+0x154/0x188)
[ 2823.213321] [<c03cb708>] (cpsw_ndo_stop) from [<c046f0ec>] (__dev_close_many+0x84/0xc8)
[ 2823.221761] [<c046f0ec>] (__dev_close_many) from [<c046f158>] (__dev_close+0x28/0x3c)
[ 2823.230012] [<c046f158>] (__dev_close) from [<c0474ca8>] (__dev_change_flags+0x88/0x160)
[ 2823.238483] [<c0474ca8>] (__dev_change_flags) from [<c0474da0>] (dev_change_flags+0x18/0x48)
[ 2823.247316] [<c0474da0>] (dev_change_flags) from [<c04d12c4>] (devinet_ioctl+0x61c/0x6e0)
[ 2823.255884] [<c04d12c4>] (devinet_ioctl) from [<c045c660>] (sock_ioctl+0x68/0x2a4)
[ 2823.263789] [<c045c660>] (sock_ioctl) from [<c0125fe4>] (do_vfs_ioctl+0x78/0x61c)
[ 2823.271629] [<c0125fe4>] (do_vfs_ioctl) from [<c01265ec>] (SyS_ioctl+0x64/0x74)
[ 2823.279284] [<c01265ec>] (SyS_ioctl) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dual EMAC works with VLAN segregation of the ports, so default vlan needs
to be added in dual EMAC case else default vlan will be tagged for all
egress packets and vlan unaware switches/servers will drop packets
from the EVM.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Tested-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit f280e89a (drivers: net: cpsw: fix for cpsw crash when build as modules)
moved cpts_register()/cpts_unregister() to  ndo_open()/ndo_stop(), but failed
to remove cpts_register in cpsw_probe() which leads to a double registration
and the following debug object splat.

[   18.991902] ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x2c
[   19.082249] [<c0059e80>] (init_timer_key) from [<c04965d4>] (cpts_register+0x1f0/0x2c4)
[   19.090642] [<c04965d4>] (cpts_register) from [<c04931dc>] (cpsw_ndo_open+0x780/0x81c)
[   19.098948] [<c04931dc>] (cpsw_ndo_open) from [<c0599c2c>] (__dev_open+0xb4/0x118)
Signed-off-by: NBenedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using an own copy of struct net_device_stats in struct
cpsw_priv, use stats from struct net_device. Also remove the thus
unnecessary .ndo_get_stats function, as it just returns dev->stats,
which is the default.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a CPDMA RX Descriptor leak that occurs after taking
the interface down when the CPSW is in Dual MAC mode. Previously
the CPSW_ALE port was left open up which causes packets to be received
and processed by the RX interrupt handler and were passed to the
non active network interface where they were ignored.

The fix is for the slave_stop function of the selected interface
to disable the respective CPSW_ALE Port from forwarding packets. This
blocks traffic from being received on the inactive interface.
Signed-off-by: NSchuyler Patton <spatton@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows the use of a generic timestamping phy connected
to the cpsw if CPTS support is not enabled. This also adds support
of the SIOCGMIIREG and SIOCSMIIREG, and moves handling of SIOCGMIIPHY
to the generic driver.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Reviewed-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 0cd8f9cc ("drivers: net: cpsw:
enable promiscuous mode support")

Enable promiscuous mode support for CPSW.

Introduced a crash on an am335x based board (similiar to am335x-evm).
Reason is buggy end condition in for loop in cpsw_set_promiscious()

for (i = 0; i <= priv->data.slaves; i++)

should be

for (i = 0; i < priv->data.slaves; i++)

Fix this ...
Signed-off-by: NHeiko Schocher <hs@denx.de>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's wrong if the device tree doesn't provide a phy-mode property for
the cpsw slaves as it is documented to be required in
Documentation/devicetree/bindings/net/cpsw.txt.

Anyhow it's nice to catch that problem, still more as it used to work
without this property up to commit 388367a5 (drivers: net: cpsw: use
cpsw-phy-sel driver to configure phy mode) which is in v3.13-rc1.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the GPIO bitbang MDIO driver is used instead of the Davinci MDIO driver
we need to configure the phy_id string differently. Otherwise this string
looks like this "gpio.6" instead of "gpio-0" and the PHY is not found when
phy_connect() is called.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable promiscuous mode support for CPSW.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During checking the interrupts with "cat /proc/interrupts", it is showing
device name as (null), this change was done with commit id aa1a15e2 where
request_irq is changed to devm_request_irq also changing the irq name from
platform device name to net device name, but the net device is not
registered at this point with the network frame work, so devm_request_irq
is called with device name as NULL, by which it is showed as "(null)" in
"cat /proc/interrupts". So this patch changes back irq name to platform
device name itself in devm_request_irq so that the device name shows as
below.

Previous to this patch
root@am335x-evm:~# cat /proc/interrupts
           CPU0
 28:       2265      INTC  12  edma
 30:         80      INTC  14  edma_error
 56:          0      INTC  40  (null)
 57:       1794      INTC  41  (null)
 58:          7      INTC  42  (null)
 59:          0      INTC  43  (null)

With this patch
root@am335x-evm:~# cat /proc/interrupts
           CPU0
 28:        213      INTC  12  edma
 30:          9      INTC  14  edma_error
 56:          0      INTC  40  4a100000.ethernet
 57:      16097      INTC  41  4a100000.ethernet
 58:      11964      INTC  42  4a100000.ethernet
 59:          0      INTC  43  4a100000.ethernet
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for enabling In Band mode in 10 mbps speed.
RGMII supports 1 Gig and 100 mbps mode for Forced mode of operation.
For 10mbps mode it should be configured to in band mode so that link
status, duplexity and speed are determined from the RGMII input data
stream
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CPSW and Davinci MDIO are build as modules, CPSW crashes when
accessing CPSW registers in CPSW probe. The same is working in built-in
as the CPSW clocks are enabled in Davindi MDIO probe, SO Enabling the
clocks before accessing the version register and moving out the other
register access to cpsw device open.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minor fix for printk format of a phys_addr_t, and the switch of two local
functions to static since they're not used outside of the file.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When only one port of the two port is pinned out, then dt probe is failing
because second port phy is not found. fixing this by checking the number of
slaves and breaking the loop.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is untested.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

During resume, use for_each_slave to walk the slaves of the cpsw, and
soft-reset each of them. This prevents oopses if there is only one
slave configured.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NMugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cpsw_hwtstamp_ioctl() should validate all fields of hwtstamp_config,
and the hardware version, before making any changes.  Currently it
sets the TX configuration before validating the rx_filter field
or that the hardware supports timestamping.

Also correct the error code for hardware versions that don't
support timestamping.  ENOTSUPP is used by the NFS implementation
and is not part of userland API; we want EOPNOTSUPP (which glibc
also calls ENOTSUP, with one 'P').

Untested as I don't have a cross-compiler to hand.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NMugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When interrupt pacing is enabled, receive/transmit statistics are not
updated properly by hardware which leads to ISR return with IRQ_NONE
and inturn kernel disables the interrupt. This patch removed the checking
of receive/transmit statistics from ISR.

This patch is verified with AM335x Beagle Bone Black and below is the
kernel warn when interrupt pacing is enabled.

[  104.298254] irq 58: nobody cared (try booting with the "irqpoll" option)
[  104.305356] CPU: 0 PID: 1073 Comm: iperf Not tainted 3.12.0-rc3-00342-g77d4015b #3
[  104.313284] [<c001bb84>] (unwind_backtrace+0x0/0xf0) from [<c0017db0>] (show_stack+0x10/0x14)
[  104.322282] [<c0017db0>] (show_stack+0x10/0x14) from [<c0507920>] (dump_stack+0x78/0x94)
[  104.330816] [<c0507920>] (dump_stack+0x78/0x94) from [<c0088c1c>] (__report_bad_irq+0x20/0xc0)
[  104.339889] [<c0088c1c>] (__report_bad_irq+0x20/0xc0) from [<c008912c>] (note_interrupt+0x1dc/0x23c)
[  104.349505] [<c008912c>] (note_interrupt+0x1dc/0x23c) from [<c0086d74>] (handle_irq_event_percpu+0xc4/0x238)
[  104.359851] [<c0086d74>] (handle_irq_event_percpu+0xc4/0x238) from [<c0086f24>] (handle_irq_event+0x3c/0x5c)
[  104.370198] [<c0086f24>] (handle_irq_event+0x3c/0x5c) from [<c008991c>] (handle_level_irq+0xac/0x10c)
[  104.379907] [<c008991c>] (handle_level_irq+0xac/0x10c) from [<c00866d8>] (generic_handle_irq+0x20/0x30)
[  104.389812] [<c00866d8>] (generic_handle_irq+0x20/0x30) from [<c0014ce8>] (handle_IRQ+0x4c/0xb0)
[  104.399066] [<c0014ce8>] (handle_IRQ+0x4c/0xb0) from [<c000856c>] (omap3_intc_handle_irq+0x60/0x74)
[  104.408598] [<c000856c>] (omap3_intc_handle_irq+0x60/0x74) from [<c050d8e4>] (__irq_svc+0x44/0x5c)
[  104.418021] Exception stack(0xde4f7c00 to 0xde4f7c48)
[  104.423345] 7c00: 00000001 00000000 00000000 dd002140 60000013 de006e54 00000002 00000000
[  104.431952] 7c20: de345748 00000040 c11c8588 00018ee0 00000000 de4f7c48 c009dfc8 c050d300
[  104.440553] 7c40: 60000013 ffffffff
[  104.444237] [<c050d8e4>] (__irq_svc+0x44/0x5c) from [<c050d300>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[  104.454220] [<c050d300>] (_raw_spin_unlock_irqrestore+0x34/0x44) from [<c00868c0>] (__irq_put_desc_unlock+0x14/0x38)
[  104.465295] [<c00868c0>] (__irq_put_desc_unlock+0x14/0x38) from [<c0088068>] (enable_irq+0x4c/0x74)
[  104.474829] [<c0088068>] (enable_irq+0x4c/0x74) from [<c03abd24>] (cpsw_poll+0xb8/0xdc)
[  104.483276] [<c03abd24>] (cpsw_poll+0xb8/0xdc) from [<c044ef68>] (net_rx_action+0xc0/0x1e8)
[  104.492085] [<c044ef68>] (net_rx_action+0xc0/0x1e8) from [<c0048a90>] (__do_softirq+0x100/0x27c)
[  104.501338] [<c0048a90>] (__do_softirq+0x100/0x27c) from [<c0048cd0>] (do_softirq+0x68/0x70)
[  104.510224] [<c0048cd0>] (do_softirq+0x68/0x70) from [<c0048e8c>] (local_bh_enable+0xd0/0xe4)
[  104.519211] [<c0048e8c>] (local_bh_enable+0xd0/0xe4) from [<c048c774>] (tcp_rcv_established+0x450/0x648)
[  104.529201] [<c048c774>] (tcp_rcv_established+0x450/0x648) from [<c0494904>] (tcp_v4_do_rcv+0x154/0x474)
[  104.539195] [<c0494904>] (tcp_v4_do_rcv+0x154/0x474) from [<c043d750>] (release_sock+0xac/0x1ac)
[  104.548448] [<c043d750>] (release_sock+0xac/0x1ac) from [<c04844e8>] (tcp_recvmsg+0x4d0/0xa8c)
[  104.557528] [<c04844e8>] (tcp_recvmsg+0x4d0/0xa8c) from [<c04a8720>] (inet_recvmsg+0xcc/0xf0)
[  104.566507] [<c04a8720>] (inet_recvmsg+0xcc/0xf0) from [<c0439744>] (sock_recvmsg+0x90/0xb0)
[  104.575394] [<c0439744>] (sock_recvmsg+0x90/0xb0) from [<c043b778>] (SyS_recvfrom+0x88/0xd8)
[  104.584280] [<c043b778>] (SyS_recvfrom+0x88/0xd8) from [<c043b7e0>] (sys_recv+0x18/0x20)
[  104.592805] [<c043b7e0>] (sys_recv+0x18/0x20) from [<c0013da0>] (ret_fast_syscall+0x0/0x48)
[  104.601587] handlers:
[  104.603992] [<c03acd94>] cpsw_interrupt
[  104.608040] Disabling IRQ #58

Cc: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If interrupts happen before napi_enable was called, the driver will not
work as expected. Network transmissions are impossible in this state.
This bug can be reproduced easily by restarting the network interface in
a loop. After some time any network transmissions on the network
interface will fail.

This patch fixes the bug by enabling napi before enabling the network
interface interrupts.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation searches the whole DT for nodes named
"slave".

This patch changes it to search only child nodes for slaves.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Phy mode can be configured via the cpsw-phy-sel driver, this patch enabled the
cpsw driver to utilise the api provided by the cpsw-phy-sel driver to configure
the phy mode.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans up the allocation and error unwind paths, which
allows us to carry less information in struct cpsw_priv and reduce the
amount of jump labels in the probe functions.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some phy's can be configured to enable wake on lan (e.g. at803x or marvell 88E1318S).
There is no way how to enable wol on CPSW with such connected phys. This patch
adds this support. It is provided by calling the phy's related code.

Tested on board with at8030x connected phy. Wol interrupt line is
connected to GPIO0 on am335x.
Signed-off-by: NMatus Ujhelyi <ujhelyi.m@gmail.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPSW driver no longer supports platform register as all the SoCs which has CPSW
are supporting DT only booting, so moving cpsw.h header file from platform
include to drivers/net/ethernet/ti
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>