In this case, the metadata needs to not be in the same
sector as the bitmap.
md will not read/write any bitmap metadata.  Config must be
done via sysfs and when a recovery makes the array non-degraded
again, writing 'true' to 'bitmap/can_clear' will allow bits in
the bitmap to be cleared again.
Signed-off-by: NNeilBrown <neilb@suse.de>

A new attribute directory 'bitmap' in 'md' is created which
contains files for configuring the bitmap.
'location' identifies where the bitmap is, either 'none',
or 'file' or 'sector offset from metadata'.
Writing 'location' can create or remove a bitmap.
Adding a 'file' bitmap this way is not yet supported.
'chunksize' and 'time_base' must be set before 'location'
can be set.

'chunksize' can be set before creating a bitmap, but is
currently always over-ridden by the bitmap superblock.

'time_base' and 'backlog' can be updated at any time.
Signed-off-by: NNeilBrown <neilb@suse.de>
Reviewed-by: NAndre Noll <maan@systemlinux.org>

Update md.txt to reflect recent changes in a number of sysfs
attributes.
Signed-off-by: NNeilBrown <neilb@suse.de>

 - used strict_strtoull in place of simple_strtoull
 - use my_mddev in place of rdev->mddev (they have the same value)
and more significantly,
 - don't adjust mddev->size to fit, rather reject changes which make
   rdev->size smaller than mddev->size

Adjusting mddev->size is a hangover from bind_rdev_to_array which
does a similar thing.  But it really is a better design to insist that
mddev->size is set as required, then the rdev->sizes are set to allow
for that.  The previous way invites confusion.
Signed-off-by: NNeilBrown <neilb@suse.de>

The important state change happens during an interrupt
in md_error.  So just set a flag there and call sysfs_notify
later in process context.
Signed-off-by: NNeil Brown <neilb@suse.de>

When a device fails, when a spare is activated, when
an array is reshaped, or when an array is started,
the extent to which the array is degraded can change.
Signed-off-by: NNeil Brown <neilb@suse.de>

When the 'resync' thread starts or stops, when we explicitly
set sync_action, or when we determine that there is definitely nothing
to do, we notify sync_action.

To stop "sync_action" from occasionally showing the wrong value,
we introduce a new flags - MD_RECOVERY_RECOVER - to say that a
recovery is probably needed or happening, and we make sure
that we set MD_RECOVERY_RUNNING before clearing MD_RECOVERY_NEEDED.
Signed-off-by: NNeil Brown <neilb@suse.de>

Changes in md/array_state could be of interest to a monitoring
program.  So make sure all changes trigger a notification.

Exceptions:
   changing active_idle to active is not reported because it
      is frequent and not interesting.
   changing active to active_idle is only reported on arrays
      with externally managed metadata, as it is not interesting
      otherwise.
Signed-off-by: NNeil Brown <neilb@suse.de>

Improve write performance by preventing the delayed_list from dumping all its
stripes onto the handle_list in one shot.  Delayed stripes are now further
delayed by being held on the 'hold_list'.  The 'hold_list' is bypassed when:

  * a STRIPE_IO_STARTED stripe is found at the head of 'handle_list'
  * 'handle_list' is empty and i/o is being done to satisfy full stripe-width
    write requests
  * 'bypass_count' is less than 'bypass_threshold'.  By default the threshold
    is 1, i.e. every other stripe handled is a preread stripe provided the
    top two conditions are false.

Benchmark data:
System: 2x Xeon 5150, 4x SATA, mem=1GB
Baseline: 2.6.24-rc7
Configuration: mdadm --create /dev/md0 /dev/sd[b-e] -n 4 -l 5 --assume-clean
Test1: dd if=/dev/zero of=/dev/md0 bs=1024k count=2048
  * patched:  +33% (stripe_cache_size = 256), +25% (stripe_cache_size = 512)

Test2: tiobench --size 2048 --numruns 5 --block 4096 --block 131072 (XFS)
  * patched: +13%
  * patched + preread_bypass_threshold = 0: +37%

Changes since v1:
* reduce bypass_threshold from (chunk_size / sectors_per_chunk) to (1) and
  make it configurable.  This defaults to fairness and modest performance
  gains out of the box.
Changes since v2:
* [neilb@suse.de]: kill STRIPE_PRIO_HI and preread_needed as they are not
  necessary, the important change was clearing STRIPE_DELAYED in
  add_stripe_bio and this has been moved out to make_request for the hang
  fix.
* [neilb@suse.de]: simplify get_priority_stripe
* [dan.j.williams@intel.com]: reset the bypass_count when ->hold_list is
  sampled empty (+11%)
* [dan.j.williams@intel.com]: decrement the bypass_count at the detection
  of stripes being naturally promoted off of hold_list +2%.  Note, resetting
  bypass_count instead of decrementing on these events yields +4% but that is
  probably too aggressive.
Changes since v3:
* cosmetic fixups
Tested-by: NJames W. Laferriere <babydr@baby-dragons.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This allows userspace to control resync/reshape progress and synchronise it
with other activities, such as shared access in a SAN, or backing up critical
sections during a tricky reshape.

Writing a number of sectors (which must be a multiple of the chunk size if
such is meaningful) causes a resync to pause when it gets to that point.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

"reshape_position" records how much progress has been made on a "reshape"
(adding drives, changing layout or chunksize).

When it is set, the number of drives, layout and chunksize can have
two possible values, an old an a new.

So allow these different values to be visible, and allow both old and new to
be set: Set the old ones first, then the reshape_position, then the new
values.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes typos in various Documentation txts. The patch addresses
some words starting with the letters 'Q'-'R'.
Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This patch fixes typos in various Documentation txts. The patch addresses
some words starting with the letters 'N'-'P'.
Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This patch fixes typos in various Documentation txts. This patch addresses
some words starting with the letters 'D'-'E'.
Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This patch fixes typos in various Documentation txts.
This patch addresses some words starting with the letter 'A'.
Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

md.txt has two sections describing the 'level' sysfs attribute, and some of
the text is out-of-date.  So make just one section, and make it right.

Cc: Christian Kujau <evil@g-house.de>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a new sysfs interface that allows the bitmap of an array to be dirtied.
The interface is write-only, and is used as follows:

echo "1000" > /sys/block/md2/md/bitmap

(dirty the bit for chunk 1000 [offset 0] in the in-memory and on-disk
bitmaps of array md2)

echo "1000-2000" > /sys/block/md1/md/bitmap

(dirty the bits for chunks 1000-2000 in md1's bitmap)

This is useful, for example, in cluster environments where you may need to
combine two disjoint bitmaps into one (following a server failure, after a
secondary server has taken over the array).  By combining the bitmaps on
the two servers, a full resync can be avoided (This was discussed on the
list back on March 18, 2005, "[PATCH 1/2] md bitmap bug fixes" thread).
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It appears in /sys/mdX/md/dev-YYY/state
and can be set or cleared by writing 'writemostly' or '-writemostly'
respectively.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The md/dev-XXX/state file can now be written:

 "faulty" simulates an error on the device
 "remove" removes the device from the array (if it is not busy)
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This allows the state of an md/array to be directly controlled via sysfs and
adds the ability to stop and array without tearing it down.

Array states/settings:

 clear
     No devices, no size, no level
     Equivalent to STOP_ARRAY ioctl
 inactive
     May have some settings, but array is not active
        all IO results in error
     When written, doesn't tear down array, but just stops it
 suspended (not supported yet)
     All IO requests will block. The array can be reconfigured.
     Writing this, if accepted, will block until array is quiescent
 readonly
     no resync can happen.  no superblocks get written.
     write requests fail
 read-auto
     like readonly, but behaves like 'clean' on a write request.

 clean - no pending writes, but otherwise active.
     When written to inactive array, starts without resync
     If a write request arrives then
       if metadata is known, mark 'dirty' and switch to 'active'.
       if not known, block and switch to write-pending
     If written to an active array that has pending writes, then fails.
 active
     fully active: IO and resync can be happening.
     When written to inactive array, starts with resync

 write-pending (not supported yet)
     clean, but writes are blocked waiting for 'active' to be written.

 active-idle
     like active, but no writes have been seen for a while (100msec).
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When a md array has been idle (no writes) for 20msecs it is marked as 'clean'.
 This delay turns out to be too short for some real workloads.  So increase it
to 200msec (the time to update the metadata should be a tiny fraction of that)
and make it sysfs-configurable.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Also export current (average) speed and status in sysfs.
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Writing major:minor to md/new_dev will bind that device to the array.
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This the role that a device has in an array can be viewed and set.
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If array is active, try to reshape, else just set the value.
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Store this total in superblock (As appropriate), and make it available to
userspace via sysfs.
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Allow it to be set to a particular version, or 'none'.
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

... only before array is started of course.
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

See patch to md.txt for more details
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Document in Documentation/md.txt the files that now appear in sysfs, and make
a couple of small refinements to exactly when 'level' and 'raid_disks' are
empty, to make it match the documentation.
Signed-off-by: NNeil Brown <neilb@suse.de>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!